TELTONIKA TCR100 4G WiFi Router User Guide

: June 6, 2024
: teltonika

Table of Contents

FRONT VIEW
TECHNICAL INFORMATION
SAFETY INFORMATION
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

TELTONIKA TCR100 4G WiFi Router

TELTONIKA-TCR100-4G-WiFi-Router

FRONT VIEW

BACK VIEW

POWER SOCKET PINOUT

HARDWARE INSTALLATION

Pull out the SIM needle from SIM holder kit.
Push the SIM holder kit button with the SIM needle.
Pull out the SIM holder.
Insert your SIM card into the SIM holder.
Slide the SIM holder back into the router.
You may store the SIM needle in the designated holder for future use
Attach all antennas.
Connect the power adapter to the 4 pin socket and then plug the other end of the power adapter into a power outlet
Connect to the device’s WiFi interface by using SSID and password or scaning QR code provided on the device information label or use an Ethernet cable connected to LAN port.

NETWORK STATUS ICONS

WiFi button – Enables/Disables WiFi radio.
WPS button – Activates WPS authentication for 120 seconds

| WiFi indication LED. When LED is lit – WiFi is enabled.
---|---
| Internet connection LED. When LED is lit – the router has an internet connection, when LED is blinking – internet connection has been lost.
| Mobile signal strength LEDs. Signal strength indicated by number of lit bars.

To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser*.
To access router’s WebUI use admin as username and password given in the information label on the bottom side of the router (image A), when prompted for authentication.
After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with the router’s WebUI before you change the password.
When you change the router’s password, the Setup wizard will start. The Setup wizard is a tool used to set up some of the router’s main operating parameters.
Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.
A.

B.

TECHNICAL INFORMATION

Radio specifications

RF technologies| 3G, 4G (LTE) Cat6, IEEE 802.11 b/g/n 2.4 GHz, IEEE 802.11 a/n/ac 5 GHz
Max RF power| 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi 2.4G, 23 dBm@WiFi 5G
Integrated antennas specifications
WiFi antennas|

2.4 GHz antenna: 2.4-2.5 GHz, VSWR<2, peak gain 1.62 dB, omnidirectional
2.4 GHz antenna: 2.4-2.5 GHz, VSWR<2, peak gain 3.97 dB, omnidirectiona
5 GHz antenna: 5.1-5.85 GHz, VSWR<2, peak gain 5.02 dB, omnidirectional

Bundled accessories specifications**
Power adapter| Input: 0.6 A@100-240 VAC, Output: 12 VDC, 1.5 A, 4-pin plug
Mobile antenna| 698~960/1710~2690 MHz, 50 Ω, VSWR

SAFETY INFORMATION

Hereby, TELTONIKA NETWORKS declares that this TCR100 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to configure it. More information on https://wiki.teltonika-networks.com/

This sign means that all used electronic and electric equipment should not be mixed with general household waste.

This sign means that product meets therequirements of the applicable EU directives.

www.teltonika-networks.com
2022 Teltonika Networks