LaserPecker2 Handheld Laser Engraver and Cutter Instruction Manual

LaserPecker 2
Operation Instruction Manual

Important note
The distance between the laser emission plate and the target surface should be 110mm. For your convenience, rotate the L-shaped ranging rod to down position, adjust the height of the lifting bracket so that the bottom of the ranging rod should be just touching the target surface (or on the same level if the shape of the target object limits their contact).

Product accessories list

|
---|---

Button/Indicator description

• Main unit/electric lifting bracket indicator

  ---

1. Preview button
2. Pa use (tap)/End (hold) button
3. Main unit indicator light **1**
4. Main unit indicator light **2**| 5. Hold to continuously rise/Tap to rise 0.3mm
6. Electric bracket power indicator
7. Hold to continuously descend/Tap to descend 0.3 mm
---|---

• Power interface

**** 1. Power outlet for electric brackets
2. Power outlet for laser protection shield ventilation fan
3. Main unit DC power interface ( 5.5mm/2.1mm jack)| 4. Power input interface of electric brackets
5. Ventilation fan
---|---

• The third axis indicator and power interface
  **** 1. The third axis power interface
  2. The third axis connection indicator| 3. The third axis power input interface
  4. The third axis auxi liary sliding module
  ---|---

Quick setup instructions

Method 1: Engrave on the electric lifting bracket

1. Secure the main unit on the electric lifting bracket and connect the power.| 2. Place the target object and adjust the height of the lifting brackets.
---|---
3. Mount the laser protection shield at the bottom of the main unit and connect to power outlet.| 4. Setup is completed. Follow APP instructions to engrave.

Method 2: Handheld engraving

| |
---|---|---
1. Mount the laser protection shield at the bottom of the main unit and connect the power.| 2. Hold the handle of the main unit and push against the target surface.| 3. Setup completed. Follow APP instructions to engrave.

Method 3: Sliding engraving

| |
---|---|---
1. Face the third-axis rollers down on the ta rget surface , use the third axis bracket to mount the main unit onto the third axis, and finally connect the power.| 1.1. Alternatively, place the third-axi s on the base of the electric lifting brackets, with rollers facing up, place a cylindrical or flat object on the rollers, and fi nally connect the power.| 2. Setup completed. Follow APP instructions to engrave.

Supplementary Installation Instructions:

• Dust filter on the back of host can be removed for cleaning

• Installation method three: sliding engraving, the third axis, electric lifting bracket, laser protective cover, Description of the power supply connections between the three accessories and the main unit

APP download and operation

1. Download APP
   • Method 1: Search for [LaserPecker] in APP markets such as Huawei App Gallery, Google Play Store, and Apple App Store to download.
   • Method 2: Scan the QR code on the right accordingly to download the APP.
   • Method 3: Download the APP from our official website www.laserpecker.net.
   http://app.appurl.me/79813076213
   Note: After installi ng the APP, pl eas e read the warnings and instructions in the APP carefully to ensure that the product is us ed correctly.

2. Power up the main unit and the electric brackets.
   

3. Connect Bluetooth
   Launch LaserPecker APP, search for your device:
   • Flashing blue light on the main unit indicates the device is standing by for Bluetooth connection;
   • Solid blue light on the main unit indicates device is connected.

4. Place the object to be engraved and adjust the height.
   Lay down the L-shaped ranging rod, and adjust the height of the bracket so that the bottom of the ranging rod just touches the engraving surface. After adjusting, the ranging rod should be retracted.

5. Follow APP instructions to engrave.
   Select desired content to be engraved on the APP’s homepage and start engraving

Technical Support

We offer global technical support. If you encounter any problems, please email support@laserpecker.com. We will get back to you as soon as possible.
Manufacturer: Shenzhen Hingin Technology Co., Ltd.
Phone: +86 0755-28913864

Product specifications

Size| Main unit: 162560122mm
Bradcet:1941535236nrrn
Range of Ming height: 0-120mm
---|---
Weight| 1748g
Laser source| 5000mW NCHIA
Laser wavelength| 450nm
Casing| Anodized aluminum alloy
Data transmission| Bluetooth 5.0
out format| G-code, common image formats Incbding, PG, PNG and more
Device Canadian method| Bluetooth, USB
Operating system| Support iOS 9.0+. Android 6.0+. Mac 10+. Windows 104
Input power| AC(100-240V, 50-60H4, DC(12V54)
°pealing temperature range| 0ºC-65ºC
Operating humidity range| 5%-80% (Non-condensing)
Safety certifications| IEC 60825-1(Laser Level-1 Safety Specllcatbn), CE, ROHS, FCC, FDA CCRH registration IEC 60825-1(Laser Level-4) KC NCC TELEC
Patents application| 7 patents

Safety guidelines

• Before setting up LaserPecker2, please first check that the equipment is in good condition and the mirror of the laser is clean.
• Installation regulation: Before operating LaserPecker2, please refer to the instruction manual to securely mount the main unit with supplied accessories (shield, electric lifting bracket or third axis) or other stable support such as tripods for DSLR cameras (not mini tripods) to avoid damage due to unstable placement.
• Please make sure a correct power supply (DC 12V5A) is used to power the main unit.
• Before engraving, please make sure to take sufficient protective measures. For example, install a protective shield, wear laser protection goggles to prevent the laser from accidentally injuring your eyes or skin. Remove irrelevant nearby objects items to prevent unnecessary damage due to laser reflections, especially flammable and explosive materials to prevent fire.
• During an ongoing engraving job, do not move device to prevent triggering an emergency stop for safety concerns.
• If you need to move the device or the target object, please do so before or after an engraving job. You must move neither the engraver nor the object when the device is engraving.
• Laser is dangerous, please do not let minors, children or anyone without sufficient self-protection awareness approach the device during an ongoing engraving job.
• Before engraving anything, please check that the target objects will not release toxic and harmful gas during the process, to avoid poisoning accidents or damages to the device itself.
• If you find excessive odor and/or smoke during engraving, please use a fan to blow it away or stop engraving and move your setup to a well-ventilated place.
• Before engraving, check whether the target surface has total reflection or diffuse reflection characteristics. Pay additional attention to safety protection for such objects. It is recommended to use a black whiteboard marker to darken the target surface before engraving.
• Do not expose skin or eyes of humans or animals directly to laser to avoid permanent damage.
• Due to the limited power of LaserPecker2, it is not yet possible to directly engrave very hard materials such as metal and glass. However, some materials can be engraved after coating with a common black whiteboard marker or thermal transfer paper.

Matters needing attention

• Please read [Safety guidelines] carefully, and familiarize yourself with the correct operating procedures.
• This product does not contain any user-replaceable components. Never attempt to disassemble LaserPecker or troubleshoot the problem by yourself.
• An operating LaserPecker emits strong laser beam which will burn skins, especially eyes of human and animals, causing serious damage. In addition, it will also damage screens of mobile phones, tablets, and any other electronic devices. Correct use and maintenance of this product is extremely important to ensure safe operations. Please strictly follow the instructions in this manual.
  When using LaserPecker, you must wear laser protection goggles at all times.

Disclaimer

Thank you for purchasing LaserPecker 2. The contents mentioned in this article is related to your safety, legal rights, and responsibilities. Before using this product, please read this article carefully to ensure that you have the correct setup for the product. Failure to follow the instructions and warnings in this document may cause injury to you and surrounding personnel, or cause damage to LaserPecker2 or other surrounding items. Once you use this product, you are deemed to have carefully read the disclaimer and warning information, understood, recognized, and accepted all terms and contents of this statement. You promise to take full responsibility for the use of this product and the possible consequences. You promise to use this product only for its designed purposes, and agree to these terms, any relevant regulations, policies, and guidelines formulated by Hingin. LaserPecker 2 is not responsible for any damage, injury, or any legal liability caused by the direct or indirect use of this product. Users should follow all safety guidelines including but not limited to the safety guidelines mentioned in this article.

Warning

• Before operating LaserPecker2, please read the contents of this manual carefully and strictly abide by the operating procedures.
• This device uses Type-4 lasers (strong laser radiation). The laser radiation may cause the following accidents: 1) Ignite the surrounding flammable materials; 2) Different materials may produce byproducts such as various radiation, harmful and toxic gases when heated by laser.3) Direct exposure of to laser radiation can cause injury to human and animals. Therefore, the operator must keep a distance from the laser source and wear protective equipment (such as laser protection goggles, protective covers, protective clothing, or firefighting equipment, etc.). It is strictly forbidden to place flammable and explosive materials near an operating laser engraver. The operator must maintain good ventilation of the working environment.
• There may be risks in the laser engraving process. The user should carefully consider whether the target material is suitable for laser engraving.
• LaserPecker 2’s designed power input is DC 12V5A. It should only be powered by a power supply of correct specifications. It is strictly forbidden to over-or under-load the engraver with an unsuitable power supply. You must ensure the AC power socket is properly earthed to prevent risk of electric shock.
• This product is equipped with very sophisticated components and dangerous laser source. It is strictly forbidden to place the equipment near electrical appliances with strong electromagnetic interference. The user must avoid direct exposure to either high or low power laser beam emitted from this device.
• It is strictly forbidden to place any irrelevant total reflection or diffuse reflection objects in the device to prevent the laser from being reflected to undesired places.
• Before using this product to engrave anything, please make sure that the emissions produced by laser irradiation of the engraved objects comply with local laws and regulations.

Copyright statement

• The copyright of this manual is the ownership rights of the software and hardware involved in the product, which belongs to Shenzhen Hingin Technology Co., Ltd. (hereinafter referred to as [Hingin Technology]). LaserPecker is a registered trademark of Hingin Technology.
• The information in this manual is subject to change without notice; and the information in this manual does not constitute a commitment of the company. Please refer to our webpage (https://www.laserpecker.net) for the most up-to-date updates.
• Except for the person who purchased this product, if without the written permission of the company, the contents of this manual shall not be rewritten and forwarded in any form or for any purpose.

Warranty terms

• To the extent permitted by law, the warranty terms are exclusive and replace all other express or implied or statutory warranty conditions, including in a special purpose, statutory or any other circumstances, including but not limited to the suitability of the product for a particular purpose Any responsibilities derived from it. In addition, Hingin Technology will not be responsible for any accidental, special, indirect or derivative damage (which may originate from use, misuse, non-use, or product defects).
• When consumers apply for warranty service, they are obliged to back up all important information and data in advance. During the maintenance process, such as replacing parts or updating the product software, the data will disappear. Hingin Technology does not provide data backup or the integrity of related data and settings.
• The product enjoys free shipping and free repair warranty service within 15 days of the shipment date, and the express delivery fee is required to pay 15 days after the shipment to the warranty period.
• Any product after replacement or repair will have the remaining warranty period of the original product or a 30-day warranty after the replacement. Hingin Technology will give the longer warranty of the two.
• Any product after replacement or repair will have the remaining warranty period of the original product or a 30-day warranty after the replacement. Hingin Technology will give the longer warranty of the two.
• For products sold in non-Mainland China regions, when consumers apply for warranty service from Hingin Technology, if the products cannot be sent back to Hingin Technology for warranty service due to the laws and regulations, safety regulations, tariffs, maintenance technology, and parts inventory of various countries and regions, sales in some countries and regions, Hixing Technology can only provide limited warranty service. Therefore, consumers in non-Mainland China regions, regardless of whether they are covered by the warranty, need to seek warranty service at the store authorized by the original country of purchase, and will be charged for inspection and manual processing. If the recipient’s country has additional tariffs, it will be borne by consumers; consumers who directly apply for warranty service from Hingin Technology will be handled in a similar manner.
• Dealers may sell Hingin Technology products they distribute to consumers in non-Mainland China areas. If they provide value-added services that are different from this warranty, the service is only valid for the area sold by the distributor. It is irrelevant to this warranty service.
• Processing quality is highly related to user operation, processing material and processing environment, and is not covered by the warranty.

FCC WARNING
This device complies with part 13 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could wid the user’s authority to operate the equipment.

NOTE: The equipment has been tested and found to comply with the Initfora Class B digital device, pursuant to Part is of the FCC Rules. These fimits are designed to provide reasonable protection against harmful interference in a reside nial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

This equipment does cause harmful interference to radio or television reception, which can be determined by fuming the equipment off and on, the users are encouraged to try to correct the interference by one or more of the following measures:

• Reonent or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure quid lines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Lee only the supplied antenna.

FCC ID: ZATNE-L2
Warning: Changes or modifications to this unit no te expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

© 2020-2030 Shenzhen Hingin Technology Co., Ltd. All rights reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>