SRP Formula R Formula Simulator Racing Pedals User Manual

SRP Formula R Formula Simulator Racing Pedals

Product Information

The product in question is a set of pedals designed for driving simulation when playing PC car racing games. The pedals are manufactured by Sim Racing Pro 2018 S.L. and are equipped with three pistons and a set of three pedals: accelerator, brake, and clutch. The electrical power supply of the machine is 5 volts USB-C, with a total power of 225mW and a total consumption of 45mAh. Please note that these consumptions are approximate and may vary depending on the performance of each element.

Product Usage Instructions

Before starting to use the pedals, please review the following instructions:

Preliminary Warnings:

• Make sure to read and understand all the warnings and safety instructions provided in section 3.

Storage and Transport:

• The weight and dimensions of the pedals should be taken into consideration during storage and transport. Refer to section 4.2 for details.
• Ensure proper storage conditions to avoid damage to the pedals.
• Section 4.3 provides guidance on storage.
• Handle the pedals with care during transport to prevent any potential damage. Section 4.4 provides further instructions.

Reviews Before Starting:

• Ensure that the pedals are properly fastened before use. Refer to section 6.1 for instructions.
• Review the connection of the pedals, especially the pedals connected to the base. Section 6.2 provides detailed guidance.

Maintenance:

• Regularly clean the pedals to keep them in optimal condition. Section 8.1 provides instructions for general cleaning.
• If necessary, refer to section 8.2 for guidance on the replacement of elements.

Attachments:

• Refer to section 9 for any additional attachments or accessories related to the pedals.

Please note that the intended use of the pedals is strictly for driving simulation when playing PC car racing games. Do not attempt to use the pedals for any other activities or with elements other than those indicated in this manual.

If you have any further questions or require technical assistance, please contact Sim Racing Pro’s technical service using the provided contact information in sections 1.3 and 2.1.

GENERAL INFORMATION

Preliminary warnings

• Be sure to observe the safety and warning notes in this manual when using the pedals.
• It is essential that you follow these instructions for the pedals for issue-free operation and to be able to file a claim under the warranty.
• The pedals must be used for the purpose for which they were built. Any other use is considered dangerous. Any liability of the manufacturer for damage that may be caused by non-compliance with the instructions in the manual is excluded.
• This manual contains important information about the operation of the pedals. For this reason, it should always be kept within reach of the user.

Manufacturer’s address:

• Sim Racing Pro 2018 S.L Carretera de Tordera, 89 17300 Blanes (Girona) Spain
• Tel + 34 627 639 716 [email protected]

Technical Service Address

• Sim Racing Pro 2018 S.L Carretera de Tordera, 89 17300 Blanes (Girona) Spain
• Tel + 34 627 639 716 [email protected]

DESCRIPTION OF THE PEDALS.

General description

• This technical manual contains all the necessary instructions for the installation, commissioning, maintenance and use of the pedals.

Parts of the pedals:

• One Base, 3 pistons, set of three pedals, accelerator, brake and clutch.

The electrical power supply of the machine:

• Power and electricity consumption: 5 volts USB-C
• Model: Sim Racing Pro
• Total Power: 225mW
• Total consumption: 45mAh
• NOTE: These consumptions are always approximate since they depend on the performance of each element.

List of parts supplied

1. set of pedals
2. Optional 9 kg spring for initial braking.
3. 1 pc Allen key nº3
4. 1 pc Allen key nº4
5. 1 pc Allen key nº5
6. 1 pc. 10 mm open-end wrench
7. 1 pc open-end wrench 13 mm
8. 1 x 2m USB cable / USB-C to USB-A
9. 1 user manual / CE certificate
10. 1 Warranty form

Working principle

• The SRP GT 3p/2p pedals
• They have the following functions: Driving Simulation

Intended use

• Driving simulation when playing PC car racing games.
• Do not carry out activities other than those for which the pedals are designed with elements other than those indicated here.
• The manufacturer of the pedals declines all responsibility for failure to comply with this warning.
• Do not exceed the working capacity of the pedals.

Predictable working conditions

• People over 6 years old may use the pedals.
• The fastening of the pedals is essential for their proper functioning.
• The correct use of the pedals and their maintenance implies their longevity.

Control panel

See point 7.3

Identification and signalling

• Signal symbols that can be found on the pedals:

DANGER! Electrical risk

• Electrical risk in the electrical panel and indicated areas.
• Note: The user must ensure that all the identification signs and warning plates on the pedals are maintained and preserved
• Under no circumstances should they be dismantled or altered.

WARNINGS AND SAFETY INSTRUCTIONS

Protection and safeguards

• The materials used in the manufacture of the pedals do not give rise to any hygienic risks, although in the event of fire, the plastic components and lubricants may give rise to toxic fumes.
• Do not carry out any maintenance or cleaning operations on the pedals or the pavement in the vicinity without first disconnecting the USB from the P

STORAGE AND TRANSPORT

Reception of the pedals.

Check whether the pedals have been damaged during transport.

Weight and dimensions

Model| Length, mm.| Width, mm.| Height, mm.| Weight, Kg.
---|---|---|---|---
SRP FORMULA-R| 441| 347| 245| 7,4 KG

See the general dimensional drawing

Storage

• No particular measures are recommended with regard to storage. If the user leaves it unused for a long time, it is recommended to protect it from dust by covering it properly and disconnecting it from any power source beforehand.

Transport and handling

• If the pedals have to be transported to another location, make sure that the instruction and maintenance manual is with the pedals so that it can be consulted at the new location.
• The total weight of it must be taken into account.

LOCATION

The pedals have been designed and are built expecting their assembly.

STANDARD FASTENING SRP

EQUIVALENT FASTENING TO G25 / G27 / G29

Unpacking

• After transport and unloading, with the pedals in the vicinity of the intended assembly site, unpacking should be carried out with the utmost care and attention.
• The pedals should not be installed if any damage is observed during unpacking. In case of questions, do not use the product and ask the supplier for information.

Site preparation

• The surface on which the machine is to be installed must take account of the weight of the pedals, as indicated in section 4.1 above.
• It is recommended that it be placed on a metal frame where it can be fixed correctly. It can also be placed directly on the floor on a carpet or rubber surface.

Assembly

• Once the machine is located and level in the place where you will work on it, it can be installed and connected.

Electrical connection

• The electrical connection of the pedals is 5V via USB. As indicated in the data sheet, or in the general dimensional and connection drawing.
• The pedals require a stable, standardised supply voltage that is between the operating ranges of the pedals for proper operation. Faulty power supply to the pedals can lead to malfunction and even serious damage or deterioration of installed electrical components.
• Make sure that the electric cables connecting the pedals are not left in areas where they can hinder other users and that they are properly protected.

REVIEWS BEFORE STARTING

Fastening
Check that the pedals have been levelled out correctly, as described in section 5.3.

Review with the pedals connected

• POWER: Red LED indicating that the plate is powered by USB.
• WARNING: Orange LED failure indicator.
• INI-OK: Green LED, indicating that there is data communication with the PC.
• THROTTLE: Blue Led, throttle piston status ok.
• BRAKE: Blue Led, brake piston status ok.
• CLUTCH: Blue Led, throttle-piston status ok.
• BRAKE REGULATOR: Led Blue, Brake adjustment activated.

INSTRUCTIONS FOR USE

Pre-inspection and adjustments

• Before starting the machine, check that the pedals are connected correctly.
• Check the status of the LED indicators to determine that everything is correct. See point 6.2

Uses of the controls

• The pedals have two/three pedals, depending on the model. An accelerator
• A Brake
• A Clutch

CONTROL STINGS

Key adjustment.

• There are 9 positions for the keys. Unscrew the two Allen screws to move them (see attached drawing).

CAM ANGLE ADJUSTMENT:

• By unscrewing the two screws A (see enclosed drawing) the cams can be adjusted in the range of 70° to 90° Recommendations:
• 70º seat position in GT
  • 90º seat position at Formula (lying down)
• Applicable to the three cams accelerator, brake and clutch.

FIRMNESS ADJUSTMENT:

• Loosen screw B (see drawing below) to raise the piston for more firmness and to lower it for less firmness.
• Applicable to all three pistons equally: accelerator, brake and clutch.

BRAKE TRAVEL ADJUSTMEN

See the following video:

• SRP-GT/F1 PEDALS – ADJUSTING THE BRAKE TRAVEL On the YouTube channel: SRP SimRacing-Pro Direct link: https://youtu.be/vQphgbAFBlA.

THROTTLE TRAVEL ADJUSTMENT.

• By loosening the hexagon socket screw C (see enclosed drawing), unscrewing part D shortens the route. Unscrew a max. of 15 mm
• The pedal is supplied at a maximum route.

Download and use of the application.

• Download the application in the download area of the website sim.racing-pro.com
• Execute and follow the steps of the application for a good configuration.

MAINTENANCE

General cleaning Introduction

• It is advisable that you dust the machine periodically.
• DO NOT use cleaning fluids in the area of the plate, as this could cause damage to the machine.
• Remember that by keeping the machine in an optimum state of cleanliness and maintenance, its performance will be better and it will last longer.

Replacement of elements

• The replacement of any element must be done by the technical service or by remote connection with the technical service
• Any maintenance or cleaning operations to be carried out on or near the machine must be carried out after disconnecting the power supply.

ATTACHMENTS

Plan of general measures:

DECLARATION OF CONFORMITY

CE” BRANDING

• The plate is stamped with the manufacturer’s brand, the CE conformity brand and the manufacturer’s social information.
• On the top of the plate, the specific data of the pedals is specified: brand, model, serial number and year of manufacture.
• The last box contains the essential technical data of the pedals: the voltage,

WARRANTY

• The company SIM RACING PRO 2018, SL, is committed to ensuring the proper functioning of the pedals and the replacement of the elements that compose it due to a manufacturing defect.
• This warranty will be effective as long as the normal operation of the pedals has not been distorted or varied and the faulty element has NOT BEEN MISHANDLED OR MANIPULATED.
• Warranty: 2 years from the date of billing, except for electrical components and parts subject to normal wear and tear.

RECEIPT OF TECHNICAL DOCUMENTATION

List of documentation delivered:

• Paper support
• Instruction Manual
• CE Declaration of Conformity (included in the manual)
• Warranty sheet (included in the manual)

References

• Pro.com | Benchmark Quote | Construction Pricing Made Easy
• SRP® Simulator Racing Pro | Engineered for Victory
• SRP® Simulator Racing Pro | Engineered for Victory

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>