NUX MIGHTY BASS 50BT Digital Modeling Bass Amplifier with Bluetooth Owner’s Manual

NUX MIGHTY BASS 50BT Digital Modeling Bass Amplifier with Bluetooth Owner’s Manual

WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. This equipment. should be installed and operated with minimum distance between 2ocm the radiator your body: Use only the supplied antenna.

 The lightning symbol within a triangle means, “Electrical caution!” It indicates the presence of information about operating voltage and potential risks of electrical shock.

 The exclamation point within a triangle means, “Caution!” Please read the information next to all caution signs.

Introduction

NUX Mighty Bass 50BT is a versatile practice bass amp powerhouse. It equips a premium 6.5″ loud speaker and is driven by a 50 watt classic D power amp. Compact and portable. Practice in your bedroom at low volumes, or perform at a small club using DI out. NUX’s iconic TSAC modeling technology brings you various great sounding amp models and all of the essential effects—with excellent playability & response. Impulse Response technology offers you more Cab sound choices. That’s really a Mighty Bass Amp !

Bass lovers, we know you cherish Drum & Bass practice ! So you can engage the drum function by Application, and even record the phrase loop with original NMP-2 foot switch.

Features

• 50 watt compact modeling bass amp with 6.5″ loud speaker.
• Gate , EFX , Amp Model, IR, Modulation, Reverb.
• Drum & Loop (60s phrase loop).
• Bluetooth Audio Stream.
• Free APP controller.
• USB recording interface , firmware update, edit software.

Control Panel

POWER SWITCH
Toggle it to turn On/Off the amplifier.
POWER INDICATOR
When you turn ON the amplifier, the INDICATOR LIGHT will be OM.
INPUT JACK
Connect your bass with cable to the 1/4″ jack.
PHONE OUT
Connect your headphone to the 1/8″ jack for silent practice. The signal is the same as AMP OUT. (If you toggle IR switch, it’s related to AMP IR.)
AUX IN
If you want to use MP3 player for playback, you can connect to the 1/8″ AUX jack.
CHANNEL SWITCH & INDICATOR
You can press the INDICATOR to switch to 3 different channels. CH1 is Green, CH2 is Orange, CH3 is Red. Each channel can store all the parameters and signal block status (Engaged/Disengaged) as a preset.
GAIN
Controls the Gain of amp models.
BASS
Controls the Bass frequency level of amp models.
MIDDLE
Controls the MIDDLE frequency level of amp models.
MIDDLE FREQUENCY
Controls the Middle frequency range.
TREBLE
Controls the TREBLE frequency level of amp models.
MIDDLE FREQUENCY
Controls the Middle frequency range.
EFX INDICATOR
Press the indicator to engage EFX block, the INDICATOR LIGHT will turn on while the block is engaged.
PARAMETER 1
Controls the related EFX model parameter.

PARAMETER 2
Controls the related EFX model parameter.
Note: According to the last firmware version, there may be different EFX models. You can check PAR1 & PARA2 interactive with related parameters.

TScream
Muff| Drive
Volume|  Level

Sustain

DECAY
Controls the length of reverb.
LEVEL
Controls the mix level of reverb.

MASTER
Controls the overall volume into power amp.
LOOP INDICATOR
RED — Record , GREEN — Play , ORANGE — Dub.
BLUETOOTH INDICATOR
While the amp connects with mobile device (Bluetooth Audio Stream), the INDICATOR LIGHT will turn on, and you can hear “bi—” from the amp. If there is no connection, the INDICATOR LIGHT will flash.

For APP connection, please open the MIGHTY AMP APP, and go to “Settings” to choose “Current Amp” as “Mighty Bass”. Then click to scan devices, and you will find MIGHTY BASS 5OBT. Click it, it will connect automatically. Since connected, you can tweak all the parameters from mobile phone.

Rear Panel

DC POWER JACK
Connect with the original power adaptor to power the amp.
USB PORT
Connects the USB port with computer, you can use the related edit software. Also you can do firmware updates through USB port. Please visit the product page to check firmware update instruction, and download the newest firmware.
DI OUT
You can use DI OUT for balanced signal to interface or PA system.
GROUND LIFT TOGGLE SWITCH
If you experience ground noise issues while connecting to a PA system, you can toggle the switch up to lift the ground. It may solve the noise issue.
IR TOGGLE SWITCH
You can engage Cabinet Impulse Response signal by the independent toggle switches. DI toggle switch is related to DI OUT. AMP toggle switch is related to AMP.
FOOT SWITCH JACK
Connects with NUX NMP-2, allowing you to trigger the TIP (B foot switch) for LOOP function and trigger the RING (A foot switch) for DRUM function.

Specification

• INPUT Impedance: NPUT 1M ohms Aux-in 100K ohms
• Rated Power: 50W
• Speaker: 6.5″, 4ohm , 60W, 40Hz — 16kHz
• Power Supply: DC28V 4A (center negative)
• Dimensions: 300mm x 225mm x 326mm
• Weight: 7.2 Kg

Specifications and appearance subject to change without notice.

CE mark for European Harmonized Standards
CE Mark which is attached to our company’s products of Battery mains the product is in fully conformity with the harmonized standard(s) EN 61000-6-3:2007+A1:2011 & EN 61000-6-1:2007 Under the Council Directive 2004/108/EC on Electromagnetic Compatibility.
©2020 Cherub Technology-All rights reserved. No part of this publication may be reproduced in any form without prior written permission of Cherub Technology.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>