FIRST DEGREE FITNESS NEON Rowing Machine User Guide

FIRST DEGREE FITNESS NEON Rowing Machine

Introduction

Congratulations on your purchase of the NEON Rower. FIRST DEGREE FITNESS is proud to present the Rower as a home use product featuring patented Adjustable Fluid Resistance. Follow all instructions carefully for correct assembly, tank filling, water treatment, service and safety. Access to our world-wide distributor and service network is available at www.firstdegreefitness.com Check contents of Box 1 and 2 to assure all parts are present and correct prior to assembly.

Training with The NEON Rower

1. As with any piece of fitness equipment, consult a physician before beginning your Rower exercise program.
2. Follow instructions provided in this manual for correct foot position and basic rowing techniques.
3. For more detailed rowing techniques, please refer to our international website at www.firstdegreefitness.com

CAUTION

1. Keep hands and fingers away from moving parts, as indicated in this manual.
2. The Rower can stand vertically for storage. Make sure a secure location is chosen, such as the corner of a room or against a wall on an even, secure surface.
   Note: If the storage area is not level, an additional fixture is required (sold separately)
   to keep the Rower stable with vertical storage position

Safety

Safety Information

• Before using this product, it is essential to read this ENTIRE operation manual and ALL instructions. The Rower is intended for use solely in the manner described in this manual.
• UNDERSTANDING EACH AND EVERY WARNING TO THE FULLEST IS IMPORTANT
• As with any piece of fitness equipment, consult a physician before beginning your Rower exercise program.
• Please be aware that any fitness regiment, before being undertaken, is best preceded by a physical checkup from a certified physician.
• Injuries to health may result from incorrect or excessive training.
• WARNING Heart rate monitoring systems may be inaccurate. Over exercise may result in serious injury or death. If you feel faint, stop exercising immediately.
• Stop the machine immediately if any signs of excessive wearing is present on the belts, pulleys and bungee cords. Do not use unit until said parts are repaired or replaced.
• Do not allow children unattended access to the machine.
• The Rower can stand vertically for storage. When doing so, please follow the instructions given in the manual.
• Please keep hands away from moving parts, as indicated by the warning label on the mainframe of your machine.
• If any of the adjustment devices are left projecting, they could interfere with the user’s movement.
• Do not store in freezing conditions with water in the tank as it can expand and crack the components.

Installation

• Place on a stable, flat surface in a horizontal position during use for maximum stability.
• Check all belts, pulleys and bungee cords regularly for signs of wear, and replace if needed.
• Check regularly and follow all instructions for maintenance as specified in this manual.
• Replace immediately any defective parts and do not operate unit until all repairs are complete.

Proper Usage

• Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that FIRST DEGREE FITNESS equipment is used properly to avoid injury.
• Injuries may result if exercising improperly or excessively. It is recommended that all individuals consult a physician prior to commencing an exercise program. If at any time during exercise you feel faint, dizzy or experience pain, STOP EXERCISING and consult your physician.
• Keep body parts (hands, feet, hair, etc.), clothing and jewelry away from moving parts to avoid injury.
• Follow instructions provided in this manual for correct foot position and basic rowing techniques.
• For more detailed rowing techniques, please refer to our International website www.firstdegreefitness.com

Inspection

• DO NOT use or permit use of any equipment that is damaged and/or has worn or broken parts. For all FIRST DEGREE FITNESS equipment use only replacement parts supplied by FIRST DEGREE FITNESS.
• Cables and belts pose an extreme liability if used when frayed. Always replace any cable or belt at first sign of wear (consult FIRST DEGREE FITNESS if uncertain).
• EQUIPMENT MAINTENANCE – Preventative maintenance is the key to smooth operating equipment as well as to keep your liability to a minimum. Equipment needs to be inspected at regular intervals.
• Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
• DO NOT ATTEMPT TO USE OR REPAIR ANY ACCESSORY APPROVED FOR USE WITH THE FIRST DEGREE FITNESS EQUIPMENT WHICH APPEARS TO BE DAMAGED OR WORN.
• Check all belts, pulleys and bungee cords regularly for signs of wear, and replace if needed.
• Check regularly and follow all instructions for maintenance as specified in this manual.
• Replace immediately any defective parts and do not operate unit until all repairs are complete.

Operating Warnings

• Keep children away from the equipment. Parents or others supervising children must provide close supervision of children if the equipment is used in the presence of children.
• Do not allow users to wear loose fitting clothing or jewelry while using equipment. It is also recommended to have users secure long hair back and up to avoid contact with moving parts.
• All bystanders must stay clear of all users, moving parts and attached accessories and components while machine is in operation.
• WARNING Do not insert fingers into tank!
• CAUTION After rowing exercise, please allow the unit to sit for 5 minutes before standing it up for storage.
• CAUTION Do not fill past the calibration mark as indicated on the tank level sticker or water spillage can occur.
• WARNING Never operate this Rower without feet properly secured in Footstraps, or without the sliding portion of the Slider Footplate locked into position

Assembly

Specifications

• Product Class: HC
• Braking System: Speed Independent
• Product Net Weight: 32.7kg(72.09lb)
• Product Gross Weight: 39.5kg(87.08lb)
• Minimum Safe Operating Surface Area: 333cm (131.09”) x 172cm (67.71”)
• Dimensions: 2160mm(85.04”) Length x 520mm (20.47”) Width x 570mm(22.44”) Height
• Maximum User Weight: 150kg (330lb)
• Compact Footprint : 2,135mm x 550mm or upright 550mm x 540mm

Product Highlights
The live area shall be not less than 60cm (23.62”) greater than the training area in the directions from which the equipment is accessed. The live area must also include the area for emergency dismount

Live area and Training area

Note : Rower is not suitable for therapeutic purposes

Rower Box 1 & 2 Contents

Assembly Instructions

• STEP 1 Installing the Rear Brace to Seat Rail

1. Connect the Side Rail Left and Side Rail Right[2] using 4x M8x40mm Bolt[10], 8x M8 Washer, 4x M8 Nyloc Nut and Lower Rear Brace[4].
   Tip : Bumpstops facing inside of rail for correct assembly orientation.

2. Connect the Upper Rear Brace[3] using 6x M6x15mm Bolt[12], 5x M6 Washer[10] and Bungee Hook Munt[7].
   Note : Bungee Hook Mount Do Not need M6 Washe
   REQUIRED
   Side Rail Left / Right [2] Upper Rear Brace [3] Lower Rear Brace [4] Bungee Hook Mount [7] 8x M8 Washer [9] 5x M6 Washer [10] 4x M8 Nyloc Nut [11] 6x M6x15mm Bolt [12] 4x M8x40mm Bolt [14]

• STEP2 Mounting Rower Seat and Upper Mainframe
  To Install the Rower seat, spread the Left/Right Side Rail[2] slightly and drop the Rower Seat[6] into the track.
  Note: Seat indentation must face rearward.
  REQUIRED
  Left / Right Side Rail [2] Rower Seat [6]
  

• STEP3 Mounting Rower Seat and Upper MainframeInstall the Mainframe[1] onto the Side Rail Assembly[2] as shown.
  You will need 8x M8x45mm Bolt[11], 16x M8 Washer[7], and 8x M8 Nyloc Nut[9]. Secure the Front Lower Bracket first, then the Footboard. DO NOT TIGHTEN. You may find that the Lower Bracket Bolts can be difficult to access. You can tighten these bolts completely once the Rower is standing in the vertical position so for the moment, simply align and loosely thread lower bolts/nuts.
  Note : Clean wheels and tracks weekly with a soft dry cloth in order to decrease the rate of wear on both wheels and track.
  REQUIRED
  Mainframe [1] Side Rails Assembly [2] 16x M8 Washer [9] 8x Nyloc Nut [11] 8x M8x45mm Bolt [13]

• STEP4 Installing STEP 4 the Rear Brace to Seat Rail
  Mount the Transport Wheel Assembly[20] onto the Side Rail Assembly[2].
  Note : One washer on outside and one washer on the inside of the side rail
  REQUIRED
  Transport Wheel Assembly [8] WARNING
  Note : Transport wheels must be mounted on the outside of Side Rails As shown. Do not over tighten the Transport Wheel Axle as it may inhibit Transport Wheel rotation
  

STEP 5 Place VR Decal on the Footplate

VR Decal [5] arrow align with the positioning decal. Once done, remove the positioning decal
REQUIRED
VR Decal [5]

• STEP 6 Completing the Rower Assembly
  Once the Bungee Cord is attached to the Rear Brace, tighten the bolts holding the Footboard, the Mainframe to Side Rail Bolts as they are easier to access from the vertical position. Lower the Rower back to the Horizontal position and test for proper bungee recoil. Check Seat Rollers/Runners for dirt or debris before sitting on the Rower seat. Small objects captured between the seat rollers and runners can damage the wheels or running surface. Check runners for debris prior to each use and clean regularly.
  Note : The Rower Frame Bolts require periodic checking for tightness. Do this at the end of the first month of use and again after every 12 months Choose a suitable location when standing the product for storage. Install supplied 2x AA Duracell battery and check computer function. Details regarding can be found in the Computer section of this manual. Choose a flat, level surface on which to use your Rower, to avoid rocking and potential prematurewear.

Operation Instructions

• Adjustable Resistance (AR) Tank
  The Adjustable Resistance (AR) Tank, developed and patented by FIRST DEGREE FITNESS. offers a true
  multi-level experience. Water is moved between the “storage” and “active” chambers of the AR Tank. Your
  new Rowing Ergometer can adapt – at the turn of a dial – to the resistance preferred by each user in the
  home environment.

• Getting Started
  To achieve minimum resistance, select “MIN” on the tank adjuster. It takes 10 strokes to fill the central (storage) tank, leaving a minimal amount of water in the outer (active) tank. This process is always required if minimum resistance is desired. Row hard at a steady pace (20 to 25 strokes per minute [SPM]) and put some effort into the stroke, ensuring that good form is maintained. You can make adjustments to the resistance level while you row. Your Rowing Ergometer will adapt almost instantly to increases in resistance but will take up to 10 strokes to reduce the effort required, as the central (storage) tank fills up.

• Developing Your Routine
  Once you have found a level that gives you the exercise required, changes can be made to SPM and to stroke intensity to further vary your energy input. Interval training is used by most Rowers, where a period of low intensity is combined with short intervals of high intensity. Your FDF Rowing Ergometer allows for changes ‘on the fly’, to achieve multi-level resistance profiles during a single workout. For more information on exercise routines, please visit our website at www.firstdegreefitness.com

Tank Filling and Water Treatment Procedures.

1. Remove rubber fill plug from the top of the tank.

2. Place a large bucket of water next to the Rower. Position the Siphon[17] with rigid hose in the bucket, and flexible hose in the tank.
   Note : Make sure small breather valve on siphon is closed before filling.

3. Squeeze siphon to begin filling. Important: Do not overfill tank

4. When full, open the valve on the top of the siphon to allow excess water to escape.

5. Once filling is completed follow the water treatment schedule below, then replace the tank plug.

REQUIRED
Siphon [20]

CAUTION Resistance adjuster must be set to ’Max’ to allow for accurate filling capacity.
WARNING Do not overfill the tank beyond the maximum indicated level of 17 liters. Refer to the tank level decal on the lower side of the tank

INITIAL WATER TREATMENT
Add 1 x Water Treatment Tablet per full tank. DO NOT, UNDER ANY CIRCUMSTANCE, USE A WATER TREATMENT TABLET OTHER THAN THOSE SUPPLIED WITH YOUR UNIT. Your unit purchase includes 4 x Water Treatment Tablets, which is sufficient for several years of use. To purchase additional chlorine tabs, please consult your nearest regional dealer/distributor or check our website at www.firstdegreefitness.com Add 1 x Water Treatment Tablet per full tank. DO NOT, UNDER ANY CIRCUMSTANCE, USE A WATER TREATMENT TABLET OTHER THAN THOSE SUPPLIED WITH YOUR UNIT. Your unit purchase includes 4 x Water Treatment Tablets, which is sufficient for several years of use. To purchase additional chlorine tabs, please consult your nearest regional dealer/distributor or check our website at www.firstdegreefitness.com

Operation Instructions

Removing/Changing Tank Water

Row a minimum of ten complete strokes before commencing tank draining. Remove tank plug, insert rigid end of siphon into tank and begin draining.

1. Set Adjuster handle to “MIN”
2. Row at least ten strokes to fill the storage reservoir as completely as possible.
3. Remove Tank Plug.
4. Insert rigid end of siphon into the tank, and flexible hose into a large bucket.
5. Drain tank (approx. 40% of water will remain) and then refill following directions for Tank filling as described in the Tank Filling section of this manual.
   Note:

• The valve on top of the siphon must be closed to allow proper drainage.
• Water treatment will preclude the need to change tank water if the treatment schedule is maintained. Additional Water Treatment Tablet is required only when discoloration appears in the water.
• Exposure to full sunlight reduces the life of the Water Treatment Tablets. Storing the Rower away from direct sunlight will extend the time between water treatments.
• Approximately 40% of tank water will remain. It is not possible to completely drain the A/R tank without disassembly.

Long Term Water Treatment and Basic Operation

Do not use any Water Treatment Tablets other than the tablets supplied with this unit. For replacement tablets, contact your local First Degree Fitness distributor. Water treatment schedules for the FLUID ROWER will vary according to the fluid tanks exposure to sunlight, but expect 8-12 months near a bright, sunlit window and 2 years or more for a darker location. At the point of finding the water slightly cloudy, add a Water Treatment Tablet.

CAUTION
It is strongly recommended that a drop cloth be used under the fluid tank whenever the tank plug is opened for water treatment.

Operation Instructions

Start Rowing
There are six phases to completing a rowing stroke

Operation Instructions

Adjust Footplates
The Slider Footplate accommodates most foot sizes, and is designed to keep your feet securely in place as you row.
TO ADJUST :
Lift the top of the footplate from the mounting peg and slide vertically between 1-6 to suit your foot length. Secure by hooking the footplate back onto the mounting peg and pushing down firmly to
lock it into position. Place feet on the foot plates and tighten the foot straps to ensure your feet sit firmly against the heel captures.
Note : The heel capture should bend to
allow your foot to pivot naturally as you row.
WARNING : Never operate this Rower without feet properly secured in Footstraps, or without the sliding portion of the Slider Footplate locked into position

Using the FIRST DEGREE FITNESS USB Interface

Description :
The USB connectivity now built in to all new models of FDF Console and IPM allow you to enhance your exercise experience by connecting to your home PC or Laptop. Using FDF’s own sample applications you can exercise while enjoying your favorite movies. NetAthlon 2 XF for Rowers lets you race with other Internet connected Rowers in a Virtual Reality 3D environment or train solo.
Setting Up USB connectivity
1.Download and Install the USB Device Driver (CDM2xxxx_Setup.exe for 32 and 64 bit Windows 7/Vista/XP) from the FDF Website.
2.Download and Install the Sample USB Applications from the FDF Website (www.firstdegreefitness.com). Download and Install NetAthlon 2 XF for Rowers from. http://www.webracing.org/downloads.htm

Connecting Your Console

• The USB Connector is located on a flying lead at the rear of the IPM, along with the Sensor and Heart Rate Monitor Connectors.
• Connect to a Laptop or PC using a standard USB cable, you may need to wait while Windows starts the USB Device Driver.

Note : Please refer to computer manual where applicable or for further information refer to our website at www.firstdegreefitness.com

Computer Operation

Functions
Auto Start: Commence rowing to activate.
Reset all values : Press and hold RESET button for 3 seconds.
Distance : Each single press of RESET adds 100m distance, up to 1000m then adds 500m. Auto-Pause: A temporary halt in exercise will result in the following: For over 5 seconds and under 5 minutes:

1. SPM/500METER/WATT to zero.
2. Distance/TIME values are saved.
3. CAL per hour defaults to Total CAL.
4. A Resumption in exercise in less than 5 minutes will resume Distance/TIME from saved values automatically.

Auto Power Down: Over 5 minutes. All values revert to zero after restart.

Computer Instructions

NOTE : Heart Rate Kit and Chest Strap is sold separately.

WARNING Heart rate monitoring systems may be inaccurate, Over exercising may result in serious injury or death. If you feel faint stop exercising immediately!

Detaching the Rower Belt

1. To detach belt, simply pull beyond the range of the normal rowing stroke until the belt detaches from the belt bungee pulley.
   Tip: You’ll hear the Velcro separating just before the belt detaches.

2. Unhook the Bungee Shock Cord from the Rear Brace.Then, push out the Inner Clip from the Bungee Hook. Pull the Bungee through the Inner Clip until free. This will allow for the Bungee Shock Cord to be threaded completely out of the Main Frame and up to the Belt Bungee Pulley where it will be re-attached once the Rower Belt is in the proper position.

Reattaching the Rower Belt

STEP 1 :Begin reattaching the Rower Belt by threading around the Rower Belt Pulley with the Velcro side facing upward as illustrated.
STEP 2 :Next, thread the Belt around the Idle Wheel as shown. Once around the Idle Wheel, attach the Rower Belt to the Belt/Bungee Pulley. There is an obvious “lip” at the attachment point.
STEP 3 :Wind the Rower Belt onto the Belt/Bungee Pulley until the Rower Handle is as it’s furthest forward position.
STEP 4 :Rethread the Bungee Shock Cord (on opposite side of the Idle Wheel) back through the Bungee Pulleys and tie off at the Attachment Point.
STEP 5 :Recoil tension will decrease over time as the Bungee Shock Cord stretches. To increase recoil tension, simply push the Inner Clip out of the Bungee Hook from behind, pull the required amount of bungee through the Inner Clip and replace the Inner Clip into the Bungee Hook as shown below.

Hint: Before reattaching the Inner Clip/Bungee Hook, tie a slip knot under slight tension at the lower bungee pulley. This will keep the bungee under tension while reassembling the Bungee Hook.

Maintenance

All preventive maintenance activities must be performed on a regular basis. Performing routine preventive maintenance actions can aid in providing safe, trouble-free operation of all FIRST DEGREE FITNESS equipment. FIRST DEGREE FITNESS is not responsible for performing regular inspection and maintenance actions for your machines. Instruct all personnel in equipment inspection and maintenance actions and also in accident reporting and recording.

Bungee Cord

| Check every hundred hours for correct tension and for signs of wear.| The Bungee Cord should last for many years. If a Bungee Cord change is required, please contact your local service representative or go online at www.firstdegreefitness.com

for further details.

|

Rowing Belt

| Check every hundred hours for correct tension and for signs of wear.| The Rowing Belt should provide many years of trouble free use.

If a Rowing Belt change is required, please contact your local service representative or go online at www.firstdegreefitness.com for

further details.

|

Troubleshooting

had water treatment.

Local tap water is of poor quality.

| Change Rower location to reduce direct exposure to sunlight. Add water treatment or change tank water as directed in the water treatment section of this manual. Consider using distilled water to refill tank.
Rower Belt slipping off belt/ bungee pulley.| Bungee not under enough tension.

Recoil not strong enough

| Tighten Bungee Cord following the instructions in “reattaching the Rower Belt” section of this manual.
Inconsistent readings on the Rower Computer for 500meter split time and SPM (strokes per minute).| Sensor gap Faulty Sensor

Sensor has moved out of position

Wiring harness

| Use the back cover of the computer as a “Gap tool” to check the gap between sensor head and Magnetic ring, or see if the Sensor head has moved out of position.

Please contact your nearest FDF customer service center for details

The Rower Computer does not illuminate after battery installation.| Batteries installed incorrectly or need replacing.| Replace/reinstall batteries in correct position and try again. If the LCD screen fails to illuminate, try rotating the

batteries slightly in the computer. If this fails, contact your local service center.

The Rower Computer screen illuminates, but does not register when rowing.| Loose or failed connection.

Sensor gap too wide

| Check that the computer lead is connected properly. If it is connected then contact your local service center. Check Sensor gap.

Optional Fixture Kit Instructions

A fixture kit for upright storage can be purchased separately.

STEP 1 : Install the Z bracket onto the Storage Base. Note: Do not tighten the Knob and the Bolt.
STEP 2 : Install the bracket onto the Rower as shown.

International Warranty

• HOME USE
  FIRST DEGREE FITNESS Limited warrants that the NEON (model NEON), purchased from an authorized agent and in its undamaged original packaging, is free from defects in materials and workmanship. FIRST DEGREE FITNESS Limited or its agent will, at their discretion, repair or replace parts that become defective within the warranty period, subject to the specific inclusions and exclusions below.

• Main Frame – 5 Year Limited Warranty
  FIRST DEGREE FITNESS will repair or replace the Metal Frame of the Rower should it fail due to any defect in materials or workmanship within 5 years of the original purchase. Warranty does not apply to frame coating.

• Polycarbonate Tank & Seals – 3 Year Limited Warranty
  FIRST DEGREE FITNESS will repair or replace the polycarbonate tank or seals should they fail due to any defect in materials or workmanship within 3 years of the original purchase.

• Mechanical Components (of a non-wearing nature) – 2 Year Limited Warranty
  FIRST DEGREE FITNESS will repair or replace any mechanical component should it fail due to any defect in materials or workmanship within 2 years of the original purchase.

• Specific Inclusions
  Seat Frames Stainless Steel Impeller Assembly

• All Other Components (of a wearing nature) – 1 Year Limited Warranty
  FIRST DEGREE FITNESS will repair or replace any component should it fail due to any defect in materials or workmanship within 1 year of the original purchase.

• Specific Inclusions
  Bungee Recoil Cord Hand Grips & Foot Straps Polyester Rowing Belt Seat and Seat Runners All pulleys, rollers & bearings All rubber components Computer & speed sensor (excluding replaceable batteries) Footplates (pivoting & sliding)

• General Exclusions
  Damage to the finish of any part of the machine Damage due to neglect, abuse, incorrect assembly or use of the machine Any charges for freight or customs clearance associated with the return or dispatch of parts Any damage to or loss of goods during transport of any kind Any labour cost associated with a warranty claim

• General Conditions
  

  • The serial number of the machine must be correctly registered with FIRST DEGREE FITNESS Limited or one of its appointed distributors
  • FIRST DEGREE FITNESS Limited reserve the right to examine any part where replacement  is claimed under warranty
  • Warranty period applies only to the original purchaser from the date of purchase and is not transferable
  • The product must be returned to your place of purchase in original packaging with transportation, insurance and associated charges paid for by you and risk of loss or damage assumed by you
  • FIRST DEGREE FITNESS makes no other warranties except as stated here and expressly disclaims all warranties not stated in this warranty. Neither FIRST DEGREE FITNESS nor its associates shall be responsible for incidental or consequential damages
  • Manufacturer’s warranty automatically commences upon sale of the product to end user or upon the expiration of one (1) year from month of manufacture, whichever occurs first

CONTACT US
For customer support please visit firstdegreefitness.com/support
TAIWAN
T: +886 3 478 3306
764 Chung Shan South Rd Yangmei Taoyuan
Taiwan R.O.C.

Documents / Resources

| FIRST DEGREE FITNESS NEON Rowing Machine [pdf] User Guide
NEON, Rowing Machine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>