saco ZWD12270W Washer Dryer Zanussi Instruction Manual
- June 5, 2024
- saco
Table of Contents
- Detergent dispenser drawer
- Control panel
- Drying programs
- Program table
- Operating sequence
- How to change an option or program during the cycle
- How to cancel a program during the cycle
- How to open the door during the cycle of a program
- End of program
- Drying
- Auto drying 2kg of synthetics (NON-STOP program)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZWD12270W Washer Dryer Zanussi
Instruction Manual
Detergent dispenser drawer
Control panel
-
PROGRAMME SELECTOR DIAL & ON/OFF SWITCH
Allows you to select a program and/or switch the machine on/off. It can be turned either clockwise or anticlockwise. -
SPIN REDUCTION BUTTON
-
Press the spin button repeatedly to change the spin speed to a speed different from the one suggested by the washer/dryer or to select the ‘NO SPIN’ or the ‘RINSE HOLD’ option. The relevant light will light up
-
OPTIONS BUTTON
-
By pressing this button you can select one of the following options: Pre-wash, Intensive, Super Quick. The relevant light will light up.
-
EXTRA RINSE BUTTON
-
By pressing this button the machine will perform additional rinses
-
DISPLAY
-
The display shows information about the program: duration of the selected program selected drying time, incorrect option selection, alarm codes, heating phase, child safety lock, and end of program
-
START/PAUSE BUTTON
-
This will start the selected program and you can also PAUSE a program by pressing this button
-
DRYING TIME BUTTON
-
By pressing this button you can select a timed program for cotton or synthetics, and the relevant light will illuminate
-
PROGRAMME PROGRESS DISPLAY
-
The different pilot lights illuminate during the washing phase, the drying phase, and at the end of the cycle
Drying programs
Program table
Operating sequence
-
Load the laundry
-
Measure out detergent – Pour the required amount of detergent into the main wash compartment
. If you wish to carry out a prewash, pour detergent into the prewash compartment . -
Measure out fabric softener – If required pour fabric softener into the compartment marked without exceeding MAX level.
-
Switch the machine on – the display will show a blinking zero or three blinking dashes.
-
Select desired program/fabric – Once a program is selected, the relevant phase indicator lights will come on and the duration of the program will appear on the display.
-
Select temperature – The appliance will suggest a temperature for the program, if you wish to change it press the temperature button.
-
Select Spin Speed or Rinse Hold
-
Select the desired Options
-
Set the delay – Pressing the delay button repeatedly will increase the delay time, which will appear on the display for 3 seconds.
-
Start the program – press the Start/Pause button.
How to change an option or program during the cycle
First press the Start/Pause button. If the program is running, you will have to cancel the program and select a new one. The cycle will resume from the beginning and the water in the tub will not be emptied. If it is necessary to drain the water, press the Skip/Reset button repeatedly until only the Drain light is on, then restart the machine.
How to cancel a program during the cycle
Pause the machine with the Start/Pause button. Press the Skip/Reset button repeatedly until the display shows three blinking dashes.
How to open the door during the cycle of a program
It is possible to open the door of the machine while it is paused providing;
- The machine is not in the heating phase beyond 55º C
- The water level is not too high
- The drum is not turning
Otherwise, if it is absolutely necessary to open the door, switch the machine off and wait 3 seconds. Be careful of the level and the temperature of the water in the machine! Upon restarting, the cycle will resume where it was interrupted.
End of program
The machine stops automatically and the Start/Pause light goes off. If the Rinse Hold option was selected, the Rinse Hold light remains lit to indicate the water must be drained.
Drying
Drying 3kg of Cotton (which have just been washed)
- Load the laundry
- Turn the selector dial to the ‘Cotton’ program in the ‘DRYING’ sector
- Depress the ‘DRYING TIME’ button until the time you want appears on the display
- Press the START/PAUSE button to start the program
- At the end of the program, the buzzer sounds. Three flashing zeros ‘0:00’ will appear on the display. At this point, an ‘ANTI CREASE’ phase, which lasts for about 10 minutes, will start. The door can be opened only at the end of this phase.
- Turn the selector dial to the OFF position to switch the machine off. Remove the laundry
NOTE: To open the door before the anti-crease phase or to interrupt it, press any key or turn the program selector dial to any program position (except OFF) and the door can then be opened immediately
Auto drying 2kg of synthetics (NON-STOP program)
For non-stop programs DO NOT exceed the maximum load sizes of 3kg for cotton and 2kg for synthetics
- Load the laundry
- Add detergent and fabric softener
- Switch the machine on by turning the selector dial to the selected wash program/fabric
- Select the drying times
- Select the required options by using the relevant buttons. If possible do not select a spin speed lower than that suggested by the machine, to avoid too long a drying time.
- Start the program by pressing the START/PAUSE button
At the end of the programme, turn the selector dial to the OFF position to switch the machine off. Remove the laundry.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>