TRIPP-LITE N785-P01-LC-MM1 Gigabit Fiber to Ethernet Media Converters with PoE Owner’s Manual
- June 6, 2024
- Tripp Lite
Table of Contents
Owner’s Manual
Gigabit Fiber to Ethernet
Media Converters with PoE
Models (North America): N785-P01-LC-MM1,
N785-P01-SC-MM1, N785-P01-SC-MM2,
N785-P01-SC-SM1, N785-P01-SFP
Models (International): N785-INT-PLCMM1,
N785-INT-PSCMM2, N785-INT-PSFP
1111 W. 35th Street, Chicago, IL 60609 USA •
tripplite.com/support
Copyright © 2021 Tripp Lite. All rights reserved.
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—
a $100 value!
tripplite.com/warranty
http://www.tripplite.com/warranty
Package Includes
- N785-P01-Series or N785-INT-Series Media Converter
- External Power Supply with NEMA 1-15P Power Cord (100-240V), (N785-P01-Series only)
- External Power Supply with AU, EU, UK and US Power Cables (N785-INT-Series Only)
Product Features
All Models:
- Convert your fiber network to a copper network with the addition of power
- Supports 10/100/1000 Mbps speeds
- Supports up to 100 m (328 ft.) over Cat5e/Cat6 cable to your PoEcompliant device
- IEEE 802.3af Power over Ethernet (PoE) and IEEE 802.3at compliant
- Auto identification of MDI/MDI-X
- Supports full-duplex and half-duplex modes.
- LED indicators to monitor Ethernet and Fiber link status
- Link Fault Pass-Through (LFP) allows network personnel to quickly identify faults
Model| Optical Fiber
Connector| Wavelength| Mode| Max Distance
from Source
---|---|---|---|---
N785-P01-LC-MM1| LC| 850 nm| Multimode| 550 m (1804 ft.)
N785-P01-SC-MM1| SC| 850 nm| Multimode| 550 m (1804 ft.)
N785-P01-SC-MM2| SC| 1310 nm| Multimode| 2000 m (6561 ft.)
N785-P01-SC-SM1| SC| 1310 nm| Singlemode| 20 km (12.4 mi.)
N785-P01-SFP| User-Definable| Dependent on
transceivers
used| Dependent on
transceivers
used| Dependent on
transceivers used
N785-INT-PLCMM1| LC| 850 nm| Multimode| 550 m (1804 ft.)
N785-INT-PSCMM2| SC| 1310 nm| Multimode| 2000 m (6561 ft.)
N785-INT-PSFP| User-Definable| Dependent on
transceivers
used| Dependent on
transceivers
used| Dependent on
transceivers used
Accessories
All Models:
- N001-Series Cat5e Snagless Patch Cables
- N201-Series Cat6 Snagless Patch Cables
N785-P01-SFP and N785-INT-PSFP Models Only:
- N286-01GSX-MDLC SFP to LC Multimode Transceiver (850 nm / 550 m)
- N286-01GLX-SLX SFP to LC Singlemode Transceiver (1310 nm / 10 km)
Installation
Notes:
- To avoid Electrostatic Discharge (ESD) damage, it is recommended you handle the product while wearing an ESD wrist grounding strap, or touch a conductive surface (such as metal) to discharge any potential ESD prior to handling the product.
- Before installation, verify your fiber equipment’s wavelength (850 nm or 1310 nm) and model type (Single or Multi) matches that of the N785-P01-Series or N785-INT-Series Media Converter.
-
Ensure all equipment in the installation is powered off.
-
(N785-P01-SFP and N785-INT-PSFP Models Only): Install a user-supplied SFP transceiver that matches your fiber equipment’s credentials.
Note: Your fiber equipment’s wavelength and mode type must match that of the N785-P01-Series or N785-INT-Series Media Converter. -
Using existing fiber cable from your network infrastructure, connect the media converter to your fiber network.
-
With a user-supplied Cat5e/Cat6 cable (up to 100 m / 328 ft.), connect your IEEE 802.3 af/at PoE-compliant device to the media converter’s 10/100/1000Base-T UTP port.
Note: If your PoE-compliant device is farther than 100 m (328 ft.) away, moving DIP switch 3 (10M) to the ON position allows you to run an additional 230 m (750 ft.) of Cat5e/6 cable (up to 330 m / 1082 ft. away in total) at 10 Mbps speeds only. -
Connect the included power supply to the media converter.
-
Turn on power to all equipment in the installation.
DIP Switch Settings
Note: DIP switches 2 and 4 have no function.
DIP Switch 1 – Link Fault Pass-Through (LFP)
To enable the LFP function, move DIP switch 1 to the ON position.
Link Fault Pass-Through (LFP)
LFP provides constant monitoring of the links connected to the media
converter. If either the copper or fiber link fails, the media converter will
pass the fail state through both links (copper and fiber), preventing the
connected equipment from transmitting packets that would otherwise end up
lost.
The LFP function includes both the LLCF (Link Loss Carry Forward) and LLF
(Link Loss Return) functions. LLCF and LLR functions can immediately alarm
network administrators to the problem of the link media and provide an
efficient solution to monitor the network.
Link Loss Carry Forward (LLCF)
LLC occurs when a device is connected to the converter and the TP (copper)
line of the media converter loses the link, resulting in the media converter’s
fiber disconnecting from the transmission link.
Link Loss Return (LLR)
LLR occurs when a device is connected to the converter and the FP (fiber) line
loses the link, resulting in the media converter’s fiber disconnecting from
the transmission link.
DIP Switch 3 – 10M
With DIP switch 3 In the ON position, the supported transfer distance of the
RJ45 port changes to 330 m (1082 ft.), and the data transfer rate changes to
10 Mbps. This allows you to extend beyond the 100 m (328 ft.) limit while
running at lower speeds. When in this mode, speeds of 100 and 1000 Mbps are
not supported.
LED Functions
LED | Color | Status | Function |
---|---|---|---|
PWR | Green | ON | The device is powered on |
PoE | Green | ON | RJ45 port is providing DC 48V to the remote PoE device |
OFF | RJ45 port is not providing DC 48V to the remote PoE device | ||
SD | Green | ON | The fiber port is receiving an optical signal |
OFF | The fiber port is not receiving an optical signal | ||
1000M | Green | ON | 1000 Mbps speed |
OFF | 10/100 Mbps speed |
L/A – TP
(Link/Act)
(RJ45 Port)| Green| ON| Indicates the RJ45 port link is operating at
10/100/1000 Mbps
Blinking| This indicates the PoE media converter is actively sending or
receiving data over the RJ45 port
OFF| This indicates the RJ45 port link is not operating
L/A – FP
(Link/Act)
(Fiber Port)| Green| ON| Indicates the fiber port link is operating
Blinking| Indicates the PoE media converter is actively sending or receiving
data over the fiber port
OFF| This indicates the fiber port link is not operating
Warranty and Product Registration
2-YEAR LIMITED WARRANTY
TRIPP LITE warrants its products to be free from defects in materials and
workmanship for a period of two (2) years from the date of initial purchase.
TRIPP LITE’s obligation under this warranty is limited to repairing or
replacing (at its sole option) any such defective products. To obtain service
under this warranty, you must obtain a Returned Material Authorization (RMA)
number from
TRIPP LITE or an authorized TRIPP LITE service center. Products must be
returned to TRIPP LITE or an authorized TRIPP LITE service center with
transportation charges prepaid and must be accompanied by a brief description
of the problem encountered and proof of date and place of purchase. This
warranty does not apply to equipment, which has been damaged by accident,
negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties;
therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the
purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically,
TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss
of equipment, loss of use of equipment, loss of software, loss of data, costs
of substitutes, claims by third parties, or otherwise.
Product Registration
Visit www.tripplite.com/warranty today to
register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*
- No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Use of this equipment in life support applications where the failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products.
1111 W. 35th Street, Chicago, IL 60609 USA •
www.tripplite.com/support
21-09-274 93395E_RevC
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>