SONOFF B02-F Smart WiFi LED Filament Bulb User Manual

: June 6, 2024
: SonOFF

Table of Contents

SONOFF LBS B02-F WiFi Smart LED Filament Bulb User Manual
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SONOFF LBS B02-F WiFi Smart LED Filament Bulb User Manual

LBS B02-F

Operating Instruction

Install the device

To avoid electric shock, please turn off the power before installing the device.

Download APP
Power on

After powering on, the device will enter the quick pairing mode (Touch) during the first use. The device enters the “breathing mode”.
The device will exit the quick pairing mode (Touch) if not paired within 3mins. If you want to enter this mode, please press the manual switch three times repeatedly at an interval of every 1s (Off-ON-Off-ON-Off-ON). The “breathing mode” indicates the light enters quick pairing mode.
Operating Instruction Figure 4

Add the device

Tap “+” and select “ Quick Pairing ”, then operate following the prompt on the app.

Compatible Pairing Mode

If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode ” to pair.

Press the light switch 5 times repeatedly at an interval of every 1s (Off-ON-Off-ON- Off-ON-Off-ON-Off-ON) when the light is on. The “quick flash” indicates the device enters the compatible pairing mode.
Tap “+” and select “ Compatible Pairing Mode ” on APP.
Select Wi-Fi SSID with ITEAD-** and enter the password 12345678, and then go back to eWeLink APP and tap “Next”. Be patient until pairing completes.

Usage of being an ordinary bulb

Power on the bulb, it will enter quick pairing mode (The bulb change from bright to dim and cycle the mode), after 10s, if power off, it will go solid and keep warm light at the highest brightness.

Specifications

Product Introduction

Features

SONOFF LED is a LED smart bulb that allows users to adjust the brightness and color, and remotely turn on/off the connected devices via your smartphone, schedule it on/off and share it to your family to control together.

Features

Factory Reset

Press the light switch 3 times repeatedly at an interval of every 1s (Off-ON- Off-ONOff-ON) when the light is on. The “breathing mode” indicates the device enters the quick pairing mode (Touch).

Factory Reset

Please reset the device to factory defaults if you want to use other Wi-Fi networks, then reconnect the network.

Common Problems

Why my device stays “Offline”?

Maybe you have entered a wrong Wi-Fi password.
Maybe there’s too much distance between the switch your router or the environment causes interference, consider getting close to the router. If failed, please add it again.
The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless network.
Maybe the MAC address filtering is open. Please turn it off.

If none of the above methods solved the problem, you can open the mobile datanetwork on your phone to create a Wi-Fi hotspot, then add the device again.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type B02-F-A19, B02-F-A60, B02-F-ST64 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

https://sonoff.tech/usermanuals