GEORGE KOVACS P1555-66A-L Trizay 4 Light Black LED Pendant Light Instruction Manual
- June 13, 2024
- GEORGE KOVACS
Table of Contents
GEORGE KOVACS P1555-66A-L Trizay 4 Light Black LED Pendant Light
Product Information
The product is an indoor lighting fixture with the item number P1555-66A-L or
P1556-66A-L. It is designed to be mounted on an outlet box. The fixture
includes a mounting plate, rods, canopy, glass shade, decorative nuts, metal
caps, and screws. The fixture
also comes with a support cable for wiring and a LED module for illumination.
Product Usage Instructions
-
Carefully remove the fixture from the carton and check that all parts are included.
-
Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.
-
Attach the mounting plate (A) to the outlet box using the provided mounting screws (B). Ensure that the side of the mounting plate marked GND faces out.
-
Determine the desired hanging height and thread rods (F1, F2) to the coupling (E) on the top of the fixture body. Secure the canopy (C) onto rod (F1). Pass the wires carefully through each rod and canopy. Then tighten the rods and the canopy assembly until
secured. -
Adjust the arms to the proper position.
-
Align the bottom frame to the bottom of the fixture body and secure it with screws (G). Snap the four decorative nuts (H) to the bottom frame.
-
Place the glass (K) onto the fixture body and secure it with metal caps (I) and screws (J).
-
Use the support cable (P) to support the weight of the fixture while wiring. Align the fixture to the mounting plate (A) and attach the hook (T) on the end of the support cable into a slot located on the mounting plate (A). Carefully allow the support cable (P) to support the weight of the fixture while wiring.
-
Connect the electrical wires according to the provided diagram (Fig. 2). Ensure that all wire connectors are secured. If your outlet box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
mounting plate (A) using the provided green screw. After connecting the wires, tuck them carefully inside the outlet box. -
Align the canopy (C) over the mounting plate (A) and secure it with screws (D).
-
To replace the LED module, follow the steps below:
-
Shut off the power.
-
Remove screws (D) and disconnect wire connectors. Place the fixture body on a clean surface.
-
Remove screws (J) and metal caps (I) from the fixture body and remove the glass (K).
-
Press the button with printed ”L” quick connector on the LED module (L) with a screwdriver to disconnect the black wire and then disconnect the white wire from the printed ”N” quick connector on the LED module (L). Carefully remove the LED module (L) from the base.
-
Reverse steps a-d for installing the new LED module.
INSTALLATION INSTRUCTIONS
Item#P1555-66A-L P1556-66A-L (Rev. 05/09/2023) READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSEORCIRCUIT BREAKER.
PREPARATION
- Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.
- Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.
MOUNTING THE FIXYURE (Fig. 1)
- Attach mounting plate (A) to the outlet box (not included) using mounting screws (B) (Size: #8-32N*L1”L) as shown in Fig.1. Note: The side of mounting plate (A) marked “GND” must face out.
- Determine the desired hanging height and thread rods (F1, F2) to coupling (E) on the top of the fixture body. Secure canopy (C) onto rod (F1). Pass the wires carefully through each rod and canopy. Then tighten the rods and the canopy assembly until secured.
- Adjust the arms to proper position as shown in Fig.3.
- Align the bottom frame to the bottom of fixture body and secure with screws (G) using screwdriver (not included). Snap the four decorative nuts (H) to the bottom frame.
- Place glass (K) onto fixture body and secure with metal caps (I) and screws (J).
- The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (T) on the end of support cable (P) into a slot located on mounting plate (A). Carefully allow support cable (P) to support the weight of the fixture while wiring (Fig.1).
CONNECTION THE WIRES (Fig. 2)
- Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After wires are connected, tuck them carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig. 3)
- Align canopy (C) over mounting plate (A). S ecure with screws (D).
Replacing LED module (Fig.4)
The LED module can be replaced by a qualified electrician without cutting of
wire and without damage to any decorative element to which the fixture is
attached. See installation steps for more details (Fig 3.)
- a. Shut off the power.
- b. Remove screws (D) and disconnect wire connectors and place fixture body on a clean surface. (Fig1)
- c. Remove screws (J) and metal caps (I) from the fixture body and remove glass (K).
- d. Press the button with printed ”L” quick connector on LED module (L) with screwdriver (not included) to disconnect the black wire and then disconnect the white wire from the printed ”N” quick connector on LED module (L). Carefully remove LED module (L) from the base.
- e. Reverse steps a-d for installing the new LED module.
Your installation is now complete. Return power to the outlet box and test the fixture.
Note: The illustration in figure 1 on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer switches.
P1555-66A-L P1556-66A-L
Documents / Resources
|
GEORGE KOVACS P1555-66A-L Trizay 4 Light Black LED Pendant
Light
[pdf] Instruction Manual
P1555-66A-L, P1556-66A-L, P1555-66A-L Trizay 4 Light Black LED Pendant Light,
4 Light Black LED Pendant Light, LED Pendant Light, Pendant Light
---|---
|
GEORGE KOVACS P1555-66A-L Trizay 4 Light Black LED Pendant
Light
[pdf] Instruction Manual
P1555-66A-L, P1556-66A-L, P1555-66A-L Trizay 4 Light Black LED Pendant Light,
4 Light Black LED Pendant Light, LED Pendant Light, Pendant Light
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>