Kiddieware UFR201 Infrared Thermometer User Manual

Kiddieware UFR201 Infrared Thermometer

Product Information

• Product Dimensions: 350*300mm
• Weight: 80g
• Manufacturer: Shenzhen Urion Technology Co., Ltd.
• Manufacturer Address: Floor 4-6th of Building D, Jiale Science&Technology Industrial Zone, No.3, ChuangWei Road, Heshuikou Community, Marian Street, Guangming New District, 518106 Shenzhen, PEOPLE’S REPUBLIC OF CHINA
• Manufacturer Contact Information:
  • Tel: 86-755-29231308
  • E-mail: urion@urion.com.cn
• European Representative: Shanghai International Holding Corp. GmbH (Europe)
• European Representative Address: Eiffestrasse 80, 20537 Hamburg, Germany
• European Representative Contact Information:
  • Tel: +49-40-2513175
• Manufactured in: China
• Revision: 1.1

Product Usage Instructions

• Warning:
  The device is not intended for use in the emergency medical services environment.

• Setting Button:
  To switch between settings, use the setting button.

• Relative Humidity Range:
  The device can operate within a relative humidity range of up to 85%RH.

• Atmospheric Pressure Range:
  The device can operate within an atmospheric pressure range of 70kPa to 106kPa.

• Manufacturer Contact Information:
  If you have any questions or need assistance, you can contact the manufacturer:

  • Tel: 86-755-29231308
  • E-mail: urion@urion.com.cn

European Representative Contact Information:
If you are located in Europe and have any questions or need assistance, you can contact the European representative:

• Tel: +49-40-2513175

Please read the manual carefully before you use the unit, and keep it for future reference.

Introduction

• Your new Infrared thermometer uses advanced infrared (IR) technology to measure temperature instantly and accurately on the body or object.

• Easy to use and less measurement time
  This thermometer does not need to contact the body or object to ensure safety and hygiene. Its ergonomic design makes this thermometer be simple and very easy to check the temperature. It only takes 1 second to take measurement and reading.

• Body, ear, and object temperature modes
  This thermometer supports measuring the temperature of the body surface, ear canal, and object. The measuring range of object temperature mode is 0.0°C to 100.0°C(32.0°F~199.9°F). This means except for body surface, and ear canal temperature, it also supports taking the surface temperature of the object temperature as below,

  • Surface temperature of milk in the bottle
  • Surface temperature of baby bath
  • Environment temperature

• Warning sounds
  When body temperature is over 99.5°F (37.5°C ), a warning sounds 10 times

• Memory function
  It stores up to 20 sets of recent measurement data.

• Auto power off
  Automatically power off if left idle for 60‡5seconds.

• Measurement
  Measurement time is 1 second and the measurement distance is within 1 cm.

• Contraindication(s):None

• The patient is an intended operator.

• AIntended use
  The Infrared Thermometer is continuous for the continuous measurement and monitoring of human body temperature from the body surface, ear canal, or ambient. The device is indicated for use by people of all ages at home care and in hospital.

The device is not intended for use in the emergency medical services environment.

Safety Information

To assure the correct use of the product, basic safety measures should always be followed including the warning and the caution listed in the instruction manual

Symbol descriptions
The following symbols may appear in this manual, on the label, on the device, or on it’s accessories. Some of the symbols represent standards and compliances associated with the device and its use.

• This thermometer is not intended to substitute for a consultation with your physician. The body surface or ear canal scan temperature serves as a reference only. It cannot be a judgment on fever.
• Basic safety precautions should always be observed, especially when the thermometer is used on or near children and disabled persons.
• Please place the device unreachable by children or pets.
• Avoid direct sunlight
• Do not touch the lens.
• No modification of this device is allowed
• The swallowing of small parts like packing bags, batteries, battery covers and so on may cause suffocation.
• Please do not use a dilution agent, alcohol, or petrol to clean the unit. Please treat it gently and prevent it the falling from a high place.
• Please do not immerse it in liquid.
• Never leave the battery in the battery compartment for a long time without use, as it may leak and cause damage to the unit.
• Please take off the battery if you do not intend to use it within 3 months. Replace with new batteries if the unit displays a low battery symbol.
• Do not mix the old and new batteries together.
• Do not use it during transportation.

WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

Classification

1. Internally powered equipment;
2. Type BF applied part;
3. Protection against ingress of water or Particulate matter: IP21;
4. Not category AP/APG equipment;
5. Mode of operation: Intermittent operation.

The user must check that the equipment functions safely and see that it is in proper working condition before being used.

Product Structure

Display

1. Object mode symbol
2. Body mode symbol
3. Ear mode symbol
4. Temperature unit
5. Temperature reading
6. Memory mode symbol
7. Low battery indicator

Main components

1. LED screen
2. START/STOP and Measuring button
3. Mode button
4. °C/°F button
5. Auto-sense head/Probe
6. Protective cover
7. Battery cover
8. Ear Mode trigger switch

Pull off the head cover
If you want to use the ear temperature mode for measurement, please press both sides of the head cover and pull the opening cap up.

Battery Installation

Replace the batteries to ensure power supply if there is a low voltage icon for the thermometer.

• Remove the battery cover from the battery compartment as the arrow direction accordingly.
• Insert 2pcs 1.5V AAA size alkaline batteries, and ensure each battery is in the proper direction.
• Close the battery cover.

Low battery and replacement
During power on, if the low battery – symbol showing on the LED, you should replace it with new batteries, otherwise, the unit can not work.

Note:

• Please use 2 pcs of AAA alkaline batteries.
• Do not use the batteries beyond their expiry date.
• Please remove the batteries if you do not need to use them for a long time.

WARNING
Dispose of the battery in accordance with all federal, state, and local laws. To avoid fire and explosion hazards, do not burn or incinerate the battery.

Mode Setting

Body Mode

The default setting is the Body mode, and the LED screen displays the icon.

Ear Mode

Remove the front cover of the thermometer for the ear temperature measurement mode, the LED screen displays the icon, and the cover is restored to the frontal temperature mode after the measurement is completed.

Note: After removing the head cover, the device can only switch ear temperature mode.

Object Mode

• In the power-on state, short press the setting button to switch the object mode, and the LED screen displays the icon.
• Note: The Body Mode is mainly used to measure the forehead temperature, and the Ear Mode is used to measure the ear temperature, then the Object Mode is used to measure the object temperature.

Unit Switching

Press the °C/°F button when powering on after you hear 1 beep, the screen will display or the mode will change between and . When the °C/°F button is pressed. It will confirm the Celsius Unit automatically when you switch to , and confirm the Fahrenheit Unit automatically when you switch to . Then press the START/STOP button to make the confirmation selection.

Sound Switch Setting

In the power-on state, press and hold the setting button for 3 seconds to enter the sound switch setting. press the START/STOP button to confirm the selection, and after the setting, it will automatically return to the mode to be tested and wait for the measurement.

Proper use of the unit

Pre-measurement

• About Normal Body Temperature &Fever
• The temperature in the forehead and temple area differs from the internal temperature, which is taken orally or rectally.
• Vasoconstriction, an effect that constricts the blood vessels and cools the skin, can occur during the early stages of a fever.
• In this case, the temperature measured by the Infrared thermometer may be unusually low. If the measurement therefore does not match the patient’s own perception or is unusually low, repeat the measurement every 15 minutes. As a reference, you can also measure the internal body temperature using a conventional oral or rectal thermometer.
• Body temperature can vary from one individual/person to the next.
• It also varies by location on the body and time of day. Below are the statistical normal ranges from different sites.
• Please keep in mind that temperatures measured from different sites, even at the same time, should not be directly compared. Fever indicates that the body temperature is higher than normal. This symptom may be caused by infection, overdressing, or immunization. Some people may not experience fever even when they are ill.
• These include but are not limited to, infants younger than 3 months old, persons with compromised immune systems, persons taking anti- biotics, steroids, or antipyretics(aspirin, ibuprofen, acetaminophen), or persons with certain chronic illnesses. Please consult your physician when you feel ill even if you do not have a fever.

*Table1 Body Site Normal Temperature Range**

• Note: Body Temperature at WebMD;
• Website: http://firstaid.webmd.com/body-temperature;retrieved at 2010 Jan7.

As a Body Thermometer

1. Press the START/STOP button, all symbols appear on the LED, you can hear 1 short beep, then a unit or display on the screen.
2. Move the probe close to the forehead make sure the probe is flat and take measurements with a distance of 1cm. Press the START/STOP button, The meter will take measurements.
3. The measurement will be finished in 1 second, when it has been completed you can hear 1 long beep, in the meantime, the reading will appear on the LED.

As an Ear Thermometer

1. Press the START/STOP button, all symbols appear on the LED, you can hear 1 short beep, then a unit or display on the screen.
2. Pull out the protective cover of the infrared thermometer, pull the ear back, and put the detection head of the infrared thermometer into the ear canal. Press the START/STOP button, The meter will take measurements.
3. The measurement will be finished in 1 second, when it has been completed you can hear 1 long beep, in the meantime, the reading will appear on the LED.

Note:
The ear measurement mode is contact measurement. The interval between each measurement is 3~5 seconds. The buzzer emits a short beep before measuring again.

As an Object Thermometer

1. Press the START/STOP button, all symbols appear on the LED, you can hear 1 short beep, then unit or * display on the screen.
2. Press the setting button to select Object Mode.
3. Move the probe close to the object, make sure the probe is flat, and take measurements at a distance within 1cm. Press the START/STOP button, The meter will take measurements.
4. The measurement will be finished in 1 second, when it has been completed you can hear 1 long beep, in the meantime, the reading will appear on the LED.

Note:

• As the object scan temperature is likely to be affected by the surroundings, the reading shall be taken as a reference only.
• If the probe is placed at an angle close to the object scan, the reading will be affected by the surrounding temperature.

Note:

• If the reading is <37.5°C(99.5°F), the display will show together with 1 short beep.
• If the reading is≥37.5°C(99.5°F)and<43°C(109.4°F), the display will show together with 10 short beeps.
• As the forehead measurement temperature is likely to be affected by sweat, oil, and the surroundings, the reading shall be taken as a reference only.
• If the probe is placed at an angle close to the forehead measurement, the reading will be affected by the surrounding temperature.
• Babies’ skin reacts very quickly to the ambient temperature. There- fore, do not take their temperature with the non-contact thermometer during/after breastfeeding, because the skin temperature maybe lower than the internal body temperature.

Memory-recall of measurements
This thermometer automatically stores 20 sets measurements value, the oldest record will be replaced by the latest measurement value when more than 20 sets.

Read memory record

• Press the °C/°F button to enter the memory mode when power off.
• Each time you press the °C/°F button, a number (from 1 to 20) will be displayed along with the symbol , 1 second later, the measurement will be shown, as well as subsequent measurements can be display one after the other by pressing the °C/°F button each time.

Note:
The reading number “1” is the latest measurement, “20” is the oldest measurement. When the oldest measurement is read, pressing the°C/°F button again will read the reading “1” again.

Memory-clear of Measurements

• If you are sure that you want to remove all stored memories permanently.
• Longly press the C/°F button for 3 seconds until LED screen displays CLr and , after 3 short beeps, all memories will be cleared.

Specifications

Exceptional Situation

Please contact the distributor if you can not solve the problem, do not disassemble the unit by yourself!

Care and Maintenance

Care for the main unit

• Keep the unit in the storage case when not in use.
• Use an alcohol swab or cotton swab moistened with 70% alcohol to clean the thermometer casing and the measuring probe. After the alcohol has completely dried out, you can take a new measurement.
• Do not use any abrasive or volatile cleaners.
• Never immerse the unit or any of its’ component in water.

Maintenance
Do not clean the unit with naphtha, thinner or gasoline etc.

Store the unit in a clean and dry location. Do not subject the unit to extreme hot or cold temperature, humidity and direct sunlight.

Remove the batteries if the unit will not be used in 3 months or longer.

Do not use the unit under the influence of electromagnetic interference (nearby cellphones, microwave etc.)

Clinical Measurement Accuracy And Safety Verification

The product has passed clinical trials. The measured results of the infrared thermometer was compared with the measured results of mercury thermometers, the deviation average tb = 0.011°C not exceeding 0.3°C; the clinical repeatability of the infrared thermometer SR =0.100°C, not exceeding 0.3°C. The measured results up to the laboratory standard and the clinical standard. Therefore, the deviation average and the clinical repeatability of the infrared thermometer are complied with the regulatory requirement ISO 80601-2-56. The conclusions are drawn from the clinical trials, the accuracy and safety are compliedwith the regulatory requirement.

Warranty Information

• The unit is guaranteed to be free of defects in workmanship and materials under normal use for a period of 1 Year from the date of purchase.
• For repair under this warranty. Our authorized service agent must be advised of the fault within the period of the warranty. This warranty only covers parts and labor service under normal operations. Any defect resulting from natural causes, eg. flood, hurricane etc, is not covered in this guarantee. This guarantee also does not cover damage incurred by use of the unit notin accordance with the instructions, accidental damage, or being tampered or serviced by unauthorized service agents.
• The following will be excluded from this warranty-if the thermome- ter has been misused, abused, or neglect in following the manual’s instructions on purpose and unauthorized repair or modifications.
• The device requires no calibration.
• The device is not repairable and contains no user serviceable parts.

EMC

IC 60601-1-2: 2014 ME EQUIPMENT and ME SYSTEMS identifica- tion, marking and documents for Class B product

Instructions for use
The ME EQUIPMENT or ME SYSTEM is suitable for home healthcare environments and so on.

• Warning: Don’t near active HF surgical equipment and the RF shielded room of an ME system for magnetic resonance imaging, where the intensity of EM disturbances is high.
• Warning: Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
• Warning: Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improper operation.
• Warning: Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the infrared thermometer, including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.
• If any: A list of all cables and maximum lengths of cables (if applicable), transducers and other ACCESSORIES that are replaceable by the RESPONSIBLE ORGANIZATION and that are likely to affect compliance of the ME EQUIPMENT or ME SYSTEM with the requirements of Clause 7 (EMISSIONS) and Clause 8 (IMMUNITY). ACCESSORIES may be specified either generically (e.g. shielded cable, load impedance) or specifically (e.g. by MANUFACTURER and EQUIPMENT OR TYPE REFERENCE).
• If any: The performance of the ME EQUIPMENT or ME SYSTEM that was determined to be ESSENTIAL PERFORMANCE and a description of what the OPERATOR can expect if the ESSENTIAL PERFORMANCE is lost or degraded due to EM DISTURBANCES (the defined term “ESSENTIAL PERFORMANCE” need not be used).

Technical description

1. All necessary instructions for maintaining BASIC SAFETY and ESSENTIAL PERFORMANCE with regard to electromagnetic disturbances for the excepted service life.
2. Guidance and manufacturer’s declaration -electromagnetic emissions and Immunity.

Table 1

Table 2

Table 3

Manufacturer
Shenzhen Urion Technology Co.,Ltd.

• Floor 4-6th of Building D, Jiale Science&Technology Industrial Zone, No.3 , ChuangWei Road , Heshuikou Community, MaTian Street, GuangMing New District, 518106 Shenzhen, PEOPLE’S REPUBLIC OF CHINA.
• Tel: (86 ) – 755-29231308
• E-mail: urion@urion.com.cn

MADE IN CHINA.

Eu representative

• Shanghai International Holding Corp. GmbH (Europe) Eiffestrasse 80, 20537 Hamburg, Germany.
• Tel: +49-40-2513175

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>