BLAUPUNKT PP7BT Portable Bluetooth Radio with USB and Alarm Owner’s Manual

BLAUPUNKT PP7BT Portable Bluetooth Radio with USB and Alarm Owner’s Manual

Important Notes

• safety and operating instruction should be retained for future reference.
• The apparatus should not be exposed to dripping or splashing or placed in a humid atmosphere such as a bathroom.
• Do not install the product in the following areas:
• Places exposed to direct sunlight or close to radiators.
• On top of other stereo equipment that radiate too much heat.
• Blocking ventilation or in a dusty area.
• Areas where there is constant vibration.
• Humid or moist places.
• Do not place near candles or other naked flames.
• Operate the product only as instructed in this manual.
• Before turning on the power for the first time, make sure the power adaptor is properly connected.

For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts inside. Refer all servicing to qualified service personnel.

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions must be read before the product is operated.

2. Retain Instructions – The safety and operating instructions should be kept with the product for future reference.

3. Heed warnings – All warnings on the product and in the operating instructions should be adhered to.

4. Follow instructions – All operating and users’ instructions should be followed.

5. Installation – Install in accordance with the manufacturer’s instructions.

6. Power sources – This product should be operated only from the type of power source indicated by the marking adjacent to the power cord entry. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

7. Water and moisture – To reduce the risk of fire or electric shock, do not expose the product to train, dripping, splashing or excessive moisture such as in a sauna or bathroom. Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool (or similar).

8. Object and Liquid Entry – Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Do not place any object containing liquid on top of the product.

9. Servicing – Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

10. Replacement parts – When replacement parts are required, ensure that the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

11. The highest environmental temperature suitable for this product is 35°C.

12. ESD hints – If the product maybe reset or not reset to operation of control due to electrostatic discharge, just switch off and reconnect again, or move the product to another location.

13. Battery
    a. The batteries must not be exposed to excessive heat such as sunshine, fire or the like.
    b. The batteries should be drawn to the environmental aspects of battery disposal.
    c. Battery usage CAUTION-to prevent battery leakage which may result in body injuries,
    property damage, or damage to the apparatus:

    • Install all batteries correctly, + and – as marked on the apparatus.
    • Do not mix batteries (old and new or carbon and alkaline, etc.)
    • Remove batteries when the unit is not used for a long time.

ERP2 (Energy Related Products) note

This product with ecodesign complies with the stage 2 requirements of Commission Regulation (EC) NO. 1275/2008 implementing Directive 2009/125/EC regard to standby and off mode electric power consumption of electronic household and office equipment.

WARNING

This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

1. Never use the device unsupervised! Switch off the device whenever you are not using it, even if this only for a short while.
2. The appliance is not intended to be operated by means of an external timer or separate remote control system.
3. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
4. Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local power supply.
5. To prevent fire or shock hazard, do not expose this equipment to hot places, rain, moisture or dust.
6. Do not place this unit close to a strong magnetic field.
7. Do not place the unit on a amplifier or receiver.
8. Do not place this unit in a damp area as the moisture will affect the life of electric components.
9. If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the player. If this occurs, the system will not operate properly. Please leave the system turned on for about an hour until the moisture evaporates.
10. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Wipe with a clean, dry or slightly damp cloth.

NOTICE

 Conformity
Hereby, Blaupunkt Competence Center 2N-Everpol Sp. z o.o., declares that this equipment is in compliance with the essential requirement and other relevant provisions of Directive 2014/53/EU. Declaration of conformity can be obtained from the product page at www.blaupunkt.com
Responsible party: 2N-Everpol Sp. z o.o, Puławska 403A, 02-801 Warsaw, Poland, Phone: +48 22 331 99 59, E-mail: info@everpol.pl

Your products is designed a manufactured with high quality materials and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Please cat according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.

Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be dispose with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box),polystyrene foam(buffer) and poly ethylene (bags, protective foam sheet). Your system consists of material which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Recording and playback of material might require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

The Bluetooth® wordmark and logos are registered trademarks owned by Bluetooth SIG, lnc. and any use of such marks by us is under license. Other trademarks and trade names are those of their respective owners.

Many thanks to select our model, please read and reference this manual carefully before operation. Please keep the manual for future operation reference.

Control locations

1. Speaker;
2. Previous button;
3. Mode button;
4. Play/pause button;
5. Preset button;
6. Alarm button;
7. Display;
8. Next button;
9. Standby button;
10. Volume knob;
11. Repeat button(repeat one/repeat folder/random/repeat all)
12. Tune knob for FM frequency;
13. Power on/off switch;
14. DC 5V power input jack;
15. Headphone jack;
16. AUX IN jack;
17. USB playback port;
18. Power and charging LED indicator;

Power setting and battery charging

There have built in rechargeable battery inside of this unit. Before play the speaker, please follow up below step to charge the unit first.

1. Using the supplied USB cable to connect the DC 5V jack on the rear panel, and another terminal connect with supplied USB DC power adaptor. Then plug on the DC power adaptor to AC power source.
2. During the charging, the rear panel red LED indicator will turn on, and will off after be fully charged (2~2.5 hours charging time).
3. During the battery power playback mode, the unit will stop play and display off when the power is too low. Please connect power for re-charging and playing.

Note:
Your battery will last longer if you following these simple guidelines for charging and storing.
a. For charging first time, charge it at least 10 hours. And the battery will provide the best performance after fully charge and discharge 3 times. It is better to charge the unit after discharge completely, otherwise there may affect the battery’s lifetime.
b. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F).
c. Do not charge (longer than 24 hours). Excessive charging or discharging may shorten the battery’s life.
d. Due to prolong charging and discharging, the unit battery life will be affected and playback will be shorten. We cannot guarantee the same playback consistently throughout and this is not include in our warranty and service.
e. During charging, you can play the music at the same time.
f. Please do not use it under the high humidity and temperature environment for long time.
g. Please turn off the speaker if long time not to use.

Unit power on: Slide the power switch to “on” position on rear panel to power on the unit, and slide to off position to power off (display off). Short press the power button on front panel or remote controller to standby on/off the unit. Long press power button on front panel can turn off the display; long press it again to turn on. Short press mode button to switch play mode(FM/Bluetooth/USB/AUX IN) for starting operations. In case of you off the unit by side the power switch on rear panel that you cannot power on the unit by remote controller because the power is cut off completely.

Time setting: In standby mode, long press(2 seconds) mode button till the clock digits flash on display to start the setting, rotate the volume knob to adjust the hour digits, press mode button again skip to minute setting, rotate the volume knob to adjust it, and press play/pause to finish and quit the setting.

Alarm setting: short press the alarm button on front panel until clock digits flash to start the setting, rotate the volume knob to adjust the hour digits, and press alarm button again skip to the minute setting. Use the same mothed like you did for hours to adjust and finish the rest setting for minutes/alarm source(FM/USB/Beep)/alarm volume/alarm on/off, and press the alarm button to finish the alarm setting. Long press (2 seconds) alarm button to turn on or off the alarm setting. Please make sure the alarm clock symbol shows on display, which means the alarm is on, and set up successfully.
Note:
a. The clock and alarm time may reset in case of battery power exhausted, and without DC power connection. You may need set up it again after charging. We recommend to keep DC power connection in order to avoid loss time.
b. When the alarm is activate due to alarm time is being, short press the power button to cancel the alarm voice, and the unit will wake up you at same time in the coming of next day.
c. We suggest setting up the alarm volume over 15 level in order to avoid not loud enough for alarming.
d. The alarm duration time is 1 hour, and will off automatically.
e. Please make sure the USB device is available and plug on the unit properly when you choose USB as alarm source. Otherwise, the unit will switch to beep alarming.
f. You also can set up the clock and alarm by remote controller, which similar operation as front panel.
g. Please do not cut off the unit power completely ( slide power ON/OFF switch on rear panel), otherwise, the alarm cannot wake up. You can long press power button on front panel to turn off the display, but alarm keep works for you.

Radio operation
Before listen to the radio, please fully extend the antenna and move the unit next to the window in order to get better FM reception. Short press the standby button turn on/off the radio. Rotate the volume knob to adjust the output volume level.
All-in-one scan(auto scan and save as preset station): long press(2 seconds) the play/pause button to scan and save the available station automatically, max supported up to 60 preset stations. Short press the previous/next button to select and switch the preset station. Short press play/pause button can mute the sound, press it again to resume the output.

Auto tune: long press(2 seconds) the previous or next button to auto tune the available station in upward or downward frequency, and play it automatically. Tuning: Rotate the tune button to adjust the frequency gradually per 0.1MHz; You also keyin the station frequency number by digits button from remote controller to skip and get the specific station.

Manual memory station: when you tuned a favorite station by auto tuning, Short press the preset button first, press the previous or next button repeatedly to switch and select the desired preset number, press the preset button again to confirm it. Then the current station will be saved.

Bluetooth operation

This product includes Bluetooth function which can wireless playback the music from other Bluetooth device (like smart phone, tablet etc).

1. Press standby button to power on the unit, and short press mode button enter to Bluetooth model. The Bluetooth symbol will flare on display which means the unit is ready to pair.
2. Enable the Bluetooth function on your device, and search the available device (please reference your device manual for operation), then check the available Bluetooth device on the list. Select “ BP PP7BT” for pairing, and the Bluetooth symbol will stable on display after paired successful.
3. Select and play the music from your Bluetooth device, adjust the volume level on your device and radio side, then the sound will wireless play and come out from the speaker.
4. Press the previous/next button can select last and next track; press play/pause button can play or pause the playback; Long press (2seconds) the play/pause button can quit the current Bluetooth device connection, but ready to pair device; Long press(2 seconds) play/pause button again can auto pair with last paired Bluetooth device if it is available in working range.

Notices

1. All Bluetooth devices are not guaranteed for pairing successfully due to different design and brand.
2. The best working distance of Bluetooth is within 10 meters without any obstacle in between.
3. The unit only can pair and work with one Bluetooth device in one time.
4. In case of an incoming phone call during Bluetooth playback; the music will stop temporary, and resume to playback after end the phone call.

USB playback operation

Before start the USB playback operation, please insert the USB into the relative slot on the rear panel first, the unit only can detect and playback the USB when there have available device in the slot. Slide the power switch to “ on’ position on rear panel to power on the unit. Press the mode button switch and enter to USB mode, then the unit will detect and play the music automatically. While the USB mode is playing, short press play/pause button for play/pause control; short press previous/next button for previous or next track selection;  press and hold previous/next button for fast backward or forward selection and resume play after release the previous/next button.

Notes

a. Please do not use any extent USB cable for connection and playing, because that will affect signal transfer from device, an intermittent sound will happen.
b. The unit support MP3 320 kbps and WAV 192kbps, Support USB, max capacity 32GB.
c. Short press the repeat button from remote control to choose repeat mode: repeat one track, repeat folder, repeat all, and random play.
d. Fast selection: press digits 0-9 key from remote control to choose song, input 2 digits if there have saved over 10 tracks in the device ; input 3 digits if there have saved over 100 tracks in the device. For example, if you want enjoy the number 105 song, please press 1, 0, and 5 from remote control, then 0105 will display and play.

AUX IN/LINE IN and headphone.

Using the supplied 3.5mm audio cable plug into the AUX IN jack on rear panel, and the other terminal connect to other relative audio player. Power on the unit or press the mode button switch to AUX mode. Select the music from your player device and play. The sound will output from the speaker. You can get the volume up/down, MUTE, play and pause function in AUX mode.

In any play mode, if you insert headphone into the headphone jack on rear panel, there will no sound output from the speaker, but via headphone.

Remote controller operation

1. Power button: press it to standby on/off the unit.
2. Play/pause button: press it to play or pause the music playback in USB/Bluetooth mode.
3. FM scan button: press it to auto scan and save the available FM station.
4. Mode button: press it to switch the play mode between FM/Bluetooth/USB/AUX IN.
5. Mute button: press it to silence the sound, press it again to resume the sound.
6. previous/next button: Press it to switch last or next track in Bluetooth/USB mode. Press and hold it to fast-forward or fast-rewind current track, and back to normal after release in USB mode. In FM mode, press it to tune radio frequency gradually as per 0.1MHz; long press (2 seconds) it to auto tune the available station in upward or downward frequency.
7. Volume +/- button: press it to adjust the volume level.
8. Repeat button: press it repeatedly to switch the playback between repeat one/repeat folder/random/repeat all mode in USB mode.
9. Alarm button: long press(2 seconds) it to turn on/off the alarm.
10. Digits button: Press it to switch and select relevant track in USB mode. In radio mode, press it to pick up preset station; or skip to specific station in case of you key-in the relevant station’s frequency number.

Note: Please remove the battery (CR2025) insulation sheet before using the remote controller; the best working distance is within 5 meters without obstacle in between; please try your best to aim the IR sensor during operation.

Trouble shooting

1. The speaker cannot turn on.
   a. Please check if the power connection is correct.

2. No sound output.
   a. Please try to adjust the volume knob, and check the play source.
   b. please contact service center for support if the issue remained.

3. Background noise on FM station.
   a. try to move the unit in other place for better reception.
   b. scan and switch to other station for listening.

4.  Intermittent sound output in Bluetooth mode
   a. Please try to move your Bluetooth device more close to the radio.
   b. Please reference the manual for re-pairing.

5. the sound output is too small in Bluetooth mode.
   a. Please check the volume level your Bluetooth device and radio both.

Specification

Power source: DC IN 5V/1A
FM frequency: 87.5~108.0MHz
Bluetooth version: V5.0
USB 2.0, support music file: MP3/WMA/ WAV/FLAC/APE(Not guaranteed)
Built-in rechargeable battery: 3.7V/1200mA

Battery power playback time：4~5 hours depends on volume level
Battery power charging time: 2~2.5 hours.
Power consumption: 5W
Standby power consumption: <0.5W
Alarm duration: 1 hour
Time: 24HR format
(The above spec may update without priority notice.)

Power adaptor information

Manufacturer’s name or trade
mark
Commercial registration
number Address| DongGuang JunHan Technology
Co.,Limited
No.7,lane 1,The Fifth Industrial
Zone,Nanzha comunity,Humen
Town,DongGuang,GuangDong|
Model identifier| LC-H050100|
Input voltage| 100-240| V
Input AC frequency| 50/60| Hz
Output voltage| DC5| V
Output current| 1.0| A
Output power| 7.15| W
Average active efficiency| ≥73| %
Efficiency at low load (10 %)| 53%| %
No-load power consumption| ≤0.2| W

Competence Center
2N-Everpol Sp. z o.o.
ul. Pufawska 403A
02-801 Warsaw, Poland
phone: +48 22 331 99 59
e-mail: info@everpol.pl
www.blaupunkt.com

All rights reserved. All brand names are registered trademarks of their respective owners. Specifications are subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>