BLAUPUNKT XVAC Robot Vacuum Cleaner User Manual

BLAUPUNKT XVAC Robot Vacuum Cleaner

GENERAL SAFETY REGULATIONS

• Before using this product, please read the following safety instructions and follow all routine safety precautions.
• Please read the instructions carefully, please keep the instructions.
• Any operation inconsistent with this instruction manual may cause damage to this product.

NOTE!

1. Only authorized technicians can disassemble this product. Users are not recommended to disassemble this product by themselves.
2. This product can only use the power adapter provided by the factory. lf other adapters are used, the product may be damaged.
3. Do not touch wires, sockets, or power adapters when your hands are wet duct.
4. Do not use cloth curtains or body parts to roll into the product drive wheels.
5. Do not place this product near cigarette butts, lighters, and other smoldering fires.
6. Please clean the product after charging.
7.  Do not bend wires excessively or place heavy objects and sharp objects on the machine.
8. This product is an indoor household product. Do not use it outdoors.
9. Do not sit on the product.
10. Do not use this product (e. g. bathroom) in a wet environment.
11. Before using this product, please remove all vulnerable items (e. g. glasses, lamps, etc. ) on the ground as well as items (e. g. wires, paper sheets, curtains) that may entangle the side brushes and air suction passages.
12. Do not put this product in a place where it is easy to fall (e. g. on desks and chairs).
13. Please carefully check whether the power adapter is connected to the socket before use, otherwise, the battery may be damaged.
14.  To prevent tripping, please inform other members of the house when this product works.
15. Please empty the dust box before using this product when the dust box is full.
16.  The temperature used for this product is 0 to 40 degrees celsius.
17. Do not use this product in a high-temperature environment.
18. Please remove the battery from the machine before the product is scrapped.
19. Please make sure that this product is not powered on when removing the battery.
20. Please recycle the discarded batteries safely.
21. Recommended to block the staircase exit or areas where the robot may fall. The anti-drop sensors prevent the robot from tumbling downstairs and steep drops. However, they may work less effectively when dirty or used on reflective/very dark-colored floors.

WARNING

1. Use only the original rechargeable battery and charging seat specially equipped by the manufacturer. Non – rechargeable batteries are strictly prohibited, please refer to “product parameters” for battery specification information.
2. It is forbidden to use products near burning or extremely hot objects, for example, a burning fireplace.
3. It is forbidden to use products in environments with open flames or fragile objects.
4. It is forbidden to use products in extremely hot (above 40 °C) or extremely cold (below 0 °C).
5. It is forbidden to approach human hair, clothes, fingers, and other parts to the opening and operating parts of the product.
6. It is forbidden to use products on the wet or stagnant ground.
7. It is forbidden for products to absorb any particles such as stones and waste paper that may clog products.
8. It is forbidden for products to absorb any inflammable substances, such as petrol, toner, and toner for printers or photocopies. Prohibit the use of products in clean areas with flammable items.
9. It is forbidden for products to absorb any burning articles, such as cigarettes, matches, ashes, and other articles that may cause a fire.
10. It is forbidden to place articles at the suction opening. Do not use the product when the suction port is blocked. Clean up dust, cotton wool, hair, etc. at the suction opening to ensure smooth air circulation at the suction opening.
11. Use the power cord carefully to avoid damage. lt is forbidden to use the power cord to drag or pull the product and the product charging seat. lt is forbidden to use the power cord as a handle. lt is forbidden to clamp the power cord in the crack of the door. It is forbidden to pull the power cord at sharp corners and corners. lt is forbidden for the product to run on the power cord while the power cord should be far away from the heat source.
12. Do not use a damaged charging seat.
13. Even if the product has been severely damaged, burning of the product is prohibited, which may lead to an explosion of the battery of the product.

PRODUCT COMPOSITION / PACKAGE CONTENTS

PRODUCT COMPOSITION / PART NAME

• Front robot
• ROBOT
• CHARGING STATION

FUNCTIONS

INSTALLATION INSTRUCTIONS

1. Connect the power line and feed the excess wire into the slot
2. Place charging station against the wall and connect the power Please do not arbitrarily move the charging station and keep it out of direct sunlight
3. Installation of the side brushes Make the left-side brush (L) and the right-side brush (R) correspond to L and R on the bottom casing, press L and R, and the side brushes are installed when you hear a “cracking” sound

NOTE

• Direct sunlight will interfere with the charging signal and consequently, the robot may be unable to return to the charging station.
• Ensure a space of more than 0. 5m on both sides of the charging station and space above it of 1. 5m in the front
• If the power line is vertical to the ground, it may be dragged by the robot and consequently, the charging station may power off
• The charging indicator is normally on when powered on and off when charged

INSTALLATION INSTRUCTIONS

1. Connect the power line and feed the excess wire into the slot
2. Place charging station against the wall and connect the power
3. Please do not arbitrarily move the charging station and keep it out of direct sunlight
   • NOTE If the robot cannot be started due to a low battery, please charge the robot on the charging station and the robot will be started automatically. The robot can only work normally when the battery level is >20%. As shown in the picture, the charging station is correctly positioned in front of the robot and the distance between the front of the robot and the charging station should be about 2cm. The charging plates of the robot need to connect to the charging plates of the charging station.
4. Installation of the side brushes Make the left-side brush (L) and the right-side brush (R) correspond to L and R on the bottom casing, press L and R, and the side brush-es are installed when you hear a “cracking” sound
5. Starting up and charging Press and hold to switch on the robot. Charge the robot on the charging station when the power indicator light is normally on.
6. Connect the mobile APP (optional) Please download the BlueBot App in the ANDROID or IOS store. Then refer to the WiFi connection guideline in a later section of this manual, then connect mobile APP
7. Start cleaning After the robot is powered on, short press key on the robot or use the mobile APP or the remote control to start cleaning.
8. ON/OFF Press and hold the ON/OFF key for 3 seconds to turn the robot on or off
9. Clean/Pause After the machine is started, short press the ON/OFF key on the robot or start the machine using a mobile APP or the remote control.

NOTE

• The machine cannot shut down when the robot is being charged
• The cleaning robot cannot be used to remove liquids
• If the battery level is less than 20, the machine cannot work. Please charge it
• The machine will return to the charging station automatically if the battery level is less than 20%
• Please clear various wires (including power line of charging station) on the ground before use so as to avoid outage and damage of objects or wires when wires are dragged by the robot

APP CONNECTION GUIDE

INSTALLATION INSTRUCTIONS

CHARGING

• Automatic mode: The robot will return to the charging station automatically after work.
  Manual mode: In the suspended state, a short press on the HOME key on the robot or via the App or remote control to start charging. The indicator light is blinking when the robot is being charged

NOTE If the robot fails to locate the charging station, it will return to the original position automatically. Please put the robot back on the charging station manually. Push the robot gently towards the charging station until the charging plates of the robot connect with the charging plates of the charging station

CLEANING MODE

After starting, the robot will follow a zig-zag cleaning program to cover the whole floor and finish the cleaning of each room in an orderly and efficient manner. The robot will return to the charging station and charge automatically after cleaning has finished.

COMPLETED AREA

FIXED-POINT CLEANING Press and hold the Home button for 3 seconds, the robot will locate itself, clean a circular area with a diameter of 1. 5m, and will then return to the starting location and stop working automatically after the cleaning is finished.

FIXED-TIME CLEANING Fixed-time cleaning time can be set using the mobile APP. The robot will start cleaning automatically at the appointed time and return to the charging station after work

INSTALLATION INSTRUCTIONS

• WIFI RESET If the mobile phone cannot be connected to the robot due to modification of router configuration and password or for other reasons, please press and hold the key and the Home key simultaneously for 3secs until a voice prompt lets you know that the WiFi has been reset and the indicator light turns purple and flickers slowly

• SILENT MODE You can turn the robot voice on and off using the mobile APP
  RANDOM MODE (for high pile carpet): When cleaning high pile carpet, click the random mode in the APP and the robot will start random cleaning and achieve better performance. The cleaning time is unlimited until the power is less than 20% and then the robot will be charged

• ADJUSTMENT OF SUCTION POWER You can adjust the suction power to silent, standard, and high through the mobile APP

DAILY MAINTENANCE

ROLLING BRUSH (Clean it regularly)

1. Turn over the robot and press the buckle on the rolling brush cover to remove the rolling brush
2. Remove any dust outside and inside the rolling brush using a tiny brush and clean the rolling brush
3.  Re-assemble the rolling brush and press the rolling brush cover tightly to fix the buckle

DAILY MAINTENANCE

SIDE BRUSH (Clean it regularly)

1. Turn over the robot and pull the side brush out upwards
2. Remove hair and dirt and reassemble the side brush
3. Make sure the left-side brush (L) and the right-side brush (R) correspond to L and R on the bottom casing, press L and R to reinstall them

NOTE Replace the side brush every 3-6 months to ensure the cleaning effect

DUSTBIN AND FILTER (Clean it regularly)

1. Press the button and pull out the dustbin backward
2. Open and clean the dustbin

DAILY MAINTENANCE

DUSTBIN AND FILTER (Clean it regularly)

1. Press the button and pull out the dustbin backward
2. Open and clean the dustbin

FILTER CLEANING (Clean it regularly)

1.  After every cleaning round, remove the filter gauze, sponge, and HEPA filter
2.  Clean the removed filter gauze, sponge, and HEPA filter, if needed you can use water
3.  Shake off the water drops and dry them naturally, then use them after it is completely dry
4.  After it is dry, install it in the sequence, filter gauze – sponge – HEPA filter

NOTE

• Please wash the filter using clear water and do not use any detergent
• Please do not clean the filter using a brush and fingers
• Dry the filter in the air for at least 24h
• Replace the filter every 3-6 months

DAILY MAINTENANCE

SENSOR (Clean it regularly) Clean the sensors with a dry, soft cleaning cloth:

1. Clean the sensors along the wall on the right
2. Three anti-dropping sensors at the bottom of the robot
3. Infrared avoidance sensor in the front of the robot
4. Charging station: clean the charging station top, sides, and bottom (please turn the power off during cleaning)

DAILY MAINTENANCE

SENSOR (Cleaned monthly)

BATTERY

• The robot is provided with high-performance lithium-ion batteries. To maintain battery performance, please keep the robot charged in daily use
• If the robot is left unused for a long period, please shut it down and keep it properly. Charge it at least every three months to avoid damaging the batteries due to excessive discharge

FIRMWARE UPGRADE Upgrade the firmware using the mobile APP. If new firmware is detected, upgrade it according to the notification in the App. The battery level should be >50% during a firmware upgrade, so the robot should be placed on the charging station.

BASIC PARAMETERS

ROBOT

CHARGING STATION

USAGE LIMITATIONS

• The product is only used for floor cleaning in a home environment and cannot be used for outdoor (such as an open terrace), non-ground (such as a sofa), or commercial or industrial environment
• Please do not use the product in high areas (such as a penthouse, open terrace, and furniture top) without a protective fence
• Please do not use the product at a temperature above 40°C or below 0°C or when there are liquids and sticky substances on the ground
• Please hang up any cables on the ground before use to avoid being dragged by the robot
• Please clear fragile objects and impurities (such as vases and plastic bags, etc. ) from the ground to avoid damaging valuables when the robot is stuck or impacted slightly
• People with physical, mental, or perceptual disorders (including children) are not allowed to use or operate the product
• Children cannot use the product as a toy. Please keep children and pets away when the robot is working
• Please keep the main brush and other cleaning tools out of reach of children
• Please do not place objects (including children and pets) on a stationary or moving robot.
• Please keep hair, fingers, and other parts of the human body or pets away from the suction inlet when the robot is working
• Please do not use the product to clean burning objects (such as burning cigarette ends)
• Please do not use the product to clean long-piled carpet (some dark carpets may not be cleaned normally)
• Please prevent the robot from suctioning hard or sharp objects (such as waste decorative materials, glass and iron nails, etc. )
• Please do not move the robot by holding the protective cover of the laser distance sensor and collision bumper
• Please clean or maintain the robot and the charging station when shutdown or in the power-off state
• Please do not wipe any part of the product using a wet cloth or any liquid
• The LEDs emit very strong UV radiation.
• Don’t look directly into the LED light, UV radiation can harm your eyes.
• To prevent even slight exposure, wear protective eyewear.
• If LEDs are embedded in devices, please indicate using warning labels against the UV light LED used.
• Keep out of reach of children.
• Please use the product according to the User Manual. Users should be responsible for any damages and injuries caused by improper use

Battery and Charging

• Please do not use a battery, charging station, or charger provided by any third parties
• Please do not dismantle, report, or refit battery or charging station arbitrarily
• Please keep the charging station away from a heat source (such as a heating plate)
• Please do not wipe or clean the charging station dirt using a wet cloth or wet hand
• Please do not just abandon used batteries. Used batteries should be disposed of by a professional recycling agency
• If the power line is damaged or broken, please discard it immediately and replace it through official channels
• Please ensure the robot shuts down during transportation and the product should be transported in its original packaging
• If the robot is left unused for a long period, it should be fully charged and then placed in a cool and dry place. Charge the robot at least every three months to avoid damaging batteries due to excessive discharge

COMMON PROBLEMS

The robot does not start

| •  In case of a low battery level, please place the robot on the charging station and make sure that the charging plates of the robot and charging station connect. The robot will start automatically (if the robot is completely powered off, it can be started automatically after it has charged for a while)

• If the environment temperature is lower than 0°C or higher than 50°C, please use it at a temperature of 0-40°C

The robot cannot be charged

| •  Please move the robot away from the charging station and check if the indicator light of the charging station lights up. Confirm that both ends of the charging station power adapter are well connected. Make sure that the charging station is correctly positioned in front of the robot and that the distance between the front of the robot and the charging station is around 2 cm

• Check if there is poor contact between the charging plates of the robot and the charging station, please clean the charging plates or push

the side brushes aside when these block the connection between the charging plates

The robot does not recharge

|

The robot is too far away from the charging station, please put the robot near the charging station and try again

Abnormal behavior

|

Shut down the robot by pressing and holding the on/off button and restart the robot after 10 minutes

Abnormal noise

|

The main brush, side brush or wheel may be entwined with foreign matter, please shut down the robot and re-move any foreign matter

Cleaning ability declines or dust falls out

| • The dustbin is full, please clear it

• The filter is blocked, please clear or replace it

• The main brush is entwined with foreign matter, please clear it

WiFi cannot be connected

| • The WiFi signal is bad, please ensure that there is a good WiFi signal

• The WiFi is connected abnormally, please reset the WiFi (router), download the latest APP and try to reconnect it

• Password is incorrect

• The wifi is either on the 5 Ghz frequency band or on a mixed band of 2. 4 and 5 Ghz. The cleaning robot only uses the 2. 4G frequency band.

Please log in to your router and make sure that the two Ghz frequencies are split in 2. 4 and 5 Ghz and give these different names. Instruc-

tions on how to do this can be found in your router manual.

Fixed-time cleaning fails| In case of a low battery level, fixed-time cleaning can only be started when the battery level is 30% or more
Does the robot consume power when it is placed on the charging station|

The robot consumes a little power when placed on the charging station. This assures the best performance of the battery

WARRANTY

This product has 2 years warranty for manufacturing defects. The warranty period will be counted from the date of purchase of the product, according to the purchase invoice. Product warranty only covers manufacturing defects, defects resulting from improper use are not covered in the warranty, such as (but not limited to) dropping the robot, improper transportation, connection to the mains power supply not in compliance with the voltage specified in this manual, insertion of foreign objects and natural wear of parts and parts Such as plastic parts (caps, buttons, handles, latch locks, power cables, etc. ) and metal parts (wires, motors, etc. ).

Also not covered are damages due to agents of nature, lightning, flood, sea, oxidation, humidity, etc. ). The product will lose its warranty if it presents defects, which after analysis by our technicians, are characterized as being improperly used, used for professional use, or for the purpose for which it is not intended (according to the Owner’s Manual). This warranty will be void if it is found that the device has been tampered with, has been repaired by a person or service not authorized by Blaupunkt. The guarantee is only valid with the receipt/invoice provided at purchase.
Blaupunkt undertakes to provide the above-mentioned services in the warranty period only in places where it maintains an authorized service. Consumers who are not located near an authorized service center should be responsible for the costs and risks of transport to the authorized service of their choice. Natural ‘wear and tear’ are not covered under warranty. This product is for domestic use only.

DISPOSAL AND RECYCLING

This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>