Cync / C by GE Setting Up Wired Smart Switches
- June 6, 2024
- GE
Table of Contents
Setting Up Wired Smart Switches
How to setup your Cync and C by GE On/Off and Dimmer Smart Switches in the Cync app.
Our Smart Switches come in 4-Wire and 3-Wire models:
- 4-Wire Model: Requires Neutral and Ground wires.
- 3-Wire Model: Does not require Neutral wires. Only requires Ground wires.
Installing one of our switches? For assistance, select the switch you are installing:
3-Wire Smart Switches have a 15W minimum load requirement. Depending on the bulb type or the wattage of your lights, you may experience functionality issues that would require the use of the Cync Bulb Adapter (included in box) or the Fixture Adapter (available through Cync Customer Service at 1-844-302-2943). If you are experiencing functionality issues after installing your switch, check out these details on the adapter requirements.
Pairing to the CYNC App
Follow these steps to setup your 3-Wire or 4-Wire Smart Switch in the C by GE/CYNC app:
- Open the Cync app
- Select Add Devices at the bottom of your home screen
- Select the device type Wired Switches and follow the instructions on the app screens
Remember, if you want your switch to control other Cync or C by GE devices (like plugs, lights and other switches), assign the switch to the same room or group as these devices in the app.
Helpful Tips
You can create a virtual 3-way/multi-setup with more than one smart switch by assigning them to the same room or group in the app.
- Selecting a bulb type that is non-Cync will allow you to control the circuit that the switch is wired to and any Cync smart devices that are in the same room or group.
- Selecting the Cync Bulb Type will keep the circuit on and only communicate with the smart devices in the same Room or Group via Bluetooth or Wi-Fi.
Troubleshooting
Why can’t the app locate my Smart Switch?
- Make sure your phone’s Bluetooth is turned on
- Make sure the LED indicator on the switch is blinking blue, indicating that it is ready for setup. If it is not blinking blue, press and hold the on/off button for 10 seconds.
- Move your phone as close as possible to the switch during the setup process
- Power cycle the switch by pulling out the airgap at the bottom of the switch then pus back in (Dimmer and Motion Sensing Dimmer), pushing the airgap at the bottom of the switch (On/Off Button Switch), or by removing the faceplate and pushing the pinhole button (On/Off Paddle and Toggle Switch).
Why do I need to update my devices in app?
- It is important to keep your device’s firmware updated regularly. This will ensure that the devices are functioning properly and all your smart products work together to provide the best user experience.
Why did an update fail during setup?
- There are many reasons why a firmware update may have failed during execution. If a failed update occurs, try the update again. If that doesn’t resolve the issue, then one of these common issues may be the cause:
- Ensure your phone is connected to the internet using either mobile data or Wi-Fi.
- Check that Bluetooth is enabled on your smart phone. Bluetooth only devices need Bluetooth enabled to update firmware.
- Do not close the app while firmware updates are in progress. This will cancel the update.
- Stand closer to your device. When updating firmware, ensure you are no more than 40 feet from the device.
Why can’t I connect my Smart Switch to my home’s Wi-Fi network?
- If the Cync app can’t find your home Wi-Fi Network or your switch is having trouble connecting to your home Wi-Fi Network, here are some common solutions:
- Ensure that your Wi-Fi router is broadcasting a 2.4 GHz network; 5 GHz networks are not supported
- Ensure that there is a strong Wi-Fi signal strength in the switch’s location. If your phone has a weak signal in that area, then the switch will likely have a weak signal as well. Installing a Wi-Fi repeater between your router and the switch can help improve signal strength of your switch.
If these tips do not resolve your issue, you may need to factory reset your device. Resetting the device will require you to set it up in the app again. Any settings, scenes, or schedules for the device will be deleted.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>