BRAUN BC13-DCF Radio Controlled Weather Station Instructions

June 6, 2024
Braun

BRAUN BC13-DCF Radio Controlled Weather Station Instructions

BRAUN BC13-DCF Radio Controlled Weather Station

Battery precautions

  1. Do not use rechargeable batteries.
  2. Use only alkaline AA/AAA batteries of the same or equivalent type.
  3.  insert batteries with the correct polarity.
  4. Keep batteries away from children.
  5. Dispose of exhausted batteries according to local legal requirements. Do not dispose them by throwing away with normal household rubbish.
  6. Avoid short circuiting the contacts in the battery compartment and battery terminals.
  7. Remove batteries from the unit if it will not be used for long period of time.
  8. Exhausted batteries should be removed from the battery compartment to prevent over-discharge, which can cause leakage and may cause damage to the clock.

Getting started

  1. Remove the battery door.
  2. Insert 2xAA size new batteries in the main unit and 2xAAA size new batteries in the sensor as indicated in the battery compartments.
  3. To pair the main unit with the sensor, press the RESET key at the back of the main unit first, and then press the RESET key inside the battery compartment of the sensor.
  4. In some cases the main unit and the sensor will not pair immediately. You can reset the main unit and the sensor again as described in the above section. Due to the atmospheric disturbance, the best reception often occurs during night time.
  5. After the main unit and the sensor paired or 4 minutes, the Clock will automatically start scanning for the radio controlled time signal.
  6. Close the battery door.

Radio controlled operation DCF version

(Germany & European countries)
This Braun digital alarm clock is set and controlled automatically by
DCF radio signal. The DCF radio time code signal is broadcast from
Frankfurt, Germany. The coverage of the DCF signal is the whole of
Germany. The time code signal can be received up to 1500km from
Frankfurt. This covers most of Central and Western Europe.

Function keys – main unit

TIME SETTING / NEUTRAL / ALARM SETTING switch
– Slide the switch to the TIME SETTING position to set the clock time.
– Slide the switch to the ALARM SETTING position to set the alarm time.
– Slide the switch to the NEUTRAL position to exit the setting mode and return to normal display. + Key
– When the setting switch is in the NEUTRAL position, press the + key to change between 12 and 24 hour display format.
– In TIME SETTING or ALARM SETTING mode press to increase the setting value. Press and hold to speed up the setting.
– Key
– When the setting switch is in the NEUTRAL position, press the – key to change the temperature display between °C and °F format.
– In TIME SETTING or ALARM SETTING mode press to decrease the setting value. Press and hold to speed up the setting.
ALARM ON / OFF slider
– Shift the ALARM ON / OFF slider up to enable the alarm, the alarm time will show on the LCD display for 3 seconds.
– Shift the ALARM ON / OFF slider down to disable the alarm. SNOOZE / LIGHT touch button
– Tap to turn on the backlight for 10 seconds.
– Tap to stop the alarm and activate the 5 minute snooze function.
RESET key
– Press by using a pin to reset all values to default. In case of a malfunction, the unit has to be reset.
RCC key
– Press to receive the RC signal in order to test the reception.
– Press and hold the RCC key for over 3 seconds until “OFF” is displayed to disable the automatic RC function.
PAIR button
– Press to receive 433 MHz signal for sensor reception.
BACKLIGHT ON /OFF switch
– Slide the switch to ON position to enable the night light mode.
– Slide the switch to OFF position to disable the night light mode.

Function keys – sensor

°C / °F key – Press to switch between °C / °F display.
RESET key – Press by using a pin to reset all values to default. In case of a malfunction, the unit has to be reset.

Product description – main unit (Image 1)

  1. LCD display
  2. SNOOZE / LIGHT touch button
  3. ALARM ON / OFF slider
  4.  TIME SETTING / NEUTRAL / ALARM SETTING switch
  5.  + Key
  6. – Key
  7. Battery compartment
  8. RESET key
  9. PAIR button
  10. BACKLIGHT ON / OFF switch
  11. RCC key

Display details – main unit (Image 2)

A. Time
B. AM / PM indicator (for 12 hour format)
C. Alarm icon
D. Indoor temperature
E. Outdoor temperature
F. Indoor humidity
G. Outdoor humidity
H. Low battery indicator
I. Weather forecast indicator
J. Sensor signal indicator
K. DST indicator
L. RC signal strength indicator

Product description – sensor (Image 3)

  1. LCD display
  2. Wall mounting holder
  3.  Battery compartment
  4. °C / °F switch
  5.  RESET key

Display details – sensor (Image 4)

A. Outdoor temperature
B. Outdoor humidity
C. Low battery indicator
D. Sensor signal indicator

RC signal strength indicator (Image 5)

The signal indicator displays signal strength in 3 levels. Wave segment flashing means the time signals are being received. Press and hold the RCC key for over 3 seconds until “OFF” is displayed to disable the
automatic RC function.

Note: You may use the RCC key to receive the time signal manually. The receive mode stops automatically after 6 minutes.

Setting the time
  1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to the TIME SETTING position.
  2. Press the ‘+’ or ‘-’ key to set the desired value. Press and hold the ‘+’ or ‘-’ key to speed up the setting.
  3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to the NEUTRAL position to return the normal display and save the settings.
Setting the alarm
  1.  Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to the ALARM SETTING position.
  2. Press the ‘+’ or ‘-’ key to set the desired value. Press and hold the ‘+’ or ‘-’ key to speed up the setting.
  3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to the NEUTRAL position to return the normal display and save the
settings.

Using the alarm and snooze function

  1. Enable the alarm by shifting the ALARM ON / OFF slider up (so the green detail is visible). The bell icon will appear on the LCD display, and the alarm time will show on the LCD display for 3 seconds.
  2. Tap the SNOOZE / LIGHT touch button to stop the alarm and activate the snooze function. When the snooze function is activated, the bell icon will flash.
  3. To disable the alarm and snooze function, shift the ALARM ON / OFF slider down. The bell icon will disappear.
    Note: When the snooze function is activated, the alarm will automatically start again after 5 minutes. The snooze function will not stop unless the ALARM ON / OFF SLIDER is shifted down.
Placing the sensor outside
  1. Place the sensor outside within a 30 metre (98ft) range of the main unit.

  2. The sensor can be placed vertically on flat surface under a covered area which can shield it from direct sunlight or wet conditions for an accurate reading. Or it can be mounted on a wall with a screw.

  3.  Extreme temperatures, placing on wetsurface and shock should be avoided to prevent damage.

  4. If no signal is received or the transmission is interrupted, the “- -” symbol will appear on the LCD display.

  5. Ensure that the main unit and the sensor are placed within a 30 metre (98ft) range from each other. Press the PAIR button to receive the sensor signal.

  6. If the “- -” symbol is still showing on the LCD display, please reset the main unit and then the sensor.

  7. The temperature and humidity ranges are as follows. It will display
    HH when the environment is higher than this range. It will display LL when the environment is lower than this range.

Temperature Humidity
Main unit -10 ~ 50 ºC 20 ~ 95%
Sensor -20 ~ 60 ºC 20 ~ 95%

Weather forecast indicator

The built-in barometer can detect atmospheric pressure changes.
Based on the data collected, it can predict the weather condition (image 6) in the forthcoming 12 to 24 hours.

Note:

The weather forecast predicts the weather condition in the forthcoming 12 to 24 hours. It may not necessarily reflect the current situation. We do not accept any liability which may occur as a result of an incorrect
weather forecast.

Setting the night light
  1. Slide the BACKLIGHT switch to ON position to enable the night light mode.
  2. Slide the BACKLIGHT switch to OFF position to disable the night light mode.
Note:

If this feature is used continuously, the battery life will be greatly reduced.
The continuous night light mode function will temporarily be disabled for period of approx. 6 minutes at the hours of 2am 3am or 4am, as during this time the clock is updating Radio Controlled signal. Once the reception has been successfully updated the continuous night light mode will automatically be restored. During this time, if required, press Snooze/Light button to activate the backlight function for 10 seconds.

Battery replacement

When the ‘Low battery indicator’ is visible on main unit, replace with two new AA batteries at once.

When the ‘Low battery indicator’ is visible on sensor, replace with two new AAA batteries at once. Press the PAIR button on main unit to receive the sensor signal.

Important

For best reception performance, please read the following instructions.

  1. We strongly recommend you start your clock at night. Allow the clock to receive the signal automatically overnight.
  2.  Place the unit away from interfering sources such as TV set, computers, microwaves, etc.
  3. Avoid placing the unit on or next to metal surfaces.
  4. Avoid closed areas such as airports, basements, cement office buildings or factories.
    Note: Exposure to an electrostatic environment may cause the clock to reset. In this event please follow the instructions as described in this manual to set the clock again.
Guarantee

2 year guarantee against material and workmanship defects (except battery). The guarantee is valid in those countries where the alarm clock is officially being sold.
Broken or cracked lens screens are not covered under the

Braun helpline

Should you have a problem with your product, please check your local
service centre at:
www.braun-clocks.com
www.braun-watches.com
or contact +44 208 208 1833

WARNING! This product is covered by the Waste Electrical and
Electronic Equipment (WEEE) directive. It should not be discarded with normal household waste but taken to your local collection center for recycling.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals