FUJIOH FH-GS2515 SVGL Built in Gas Hob User Manual

FUJIOH FH-GS2515 SVGL Built in Gas Hob

Dear customer,
Thank you for selecting this Fujioh product.
The safety precautions and recommendations provided in the manual are for your own safety. Please keep this manual for future reference relating to the operation and maintenance of the gas hobs.
This gas hob shall be used for domestic cooking only. Any other usage is strictly prohibited. The manufacturer declines all responsibilities in the event of damages caused by improper, wrong or irrational usage of the gas hob. Read and understand the instructions before installation and operation of the gas hob.

Important safety precautions and recommendations

1. Unpack the gas hob from the carton box and inspect for physical damage. In case of doubt, do not install/operate the gas hob and contact your supplier for professional advice.

2. Nev er attempt to modify the gas hob.

3. This gas hob shall be installed in a well-ventilated room and in compliance with local regulations.

4. After cooking, ensure that the gas control knobs are turned back in the off position.

5. This gas hob can be used by children aged 14 years old and above if they understand the operation of the gas hobs and are aware of the hazards caused due to impr oper usage.

6. Do not touch the parts of the gas hob which are heated by the flame during the operation of the gas hob. Note that these parts remain hot for a certain period after the g as hob is turned off.

7. Nev er leave the gas hob unattended while cooking.

8. Never try to extinguish a cooking fire with water.

9. If the gas hob is used for a prolonged period, there may be necessary to provide more ventilation by opening more windows.

10. In the event of the burner flame being accidentally extinguished, turn off the burner control knob and do not attempt to re-ignite the burner for at
    least one minute.

11. While using the hob for the first time, you may smell some odour like a burning smell or notice a small emission of smoke. This is normal and is not toxic. This smell will go off after few usages.

Warning symbols on the toughened glass of the gas hob

• Do not place anything e.g. flame tamer or asbestos mat, between pan and pan support, as serious damage to the appliance may result in.
• Do not remove the pan support and enclose the burner with a wok stand, as this will concentrate and deflect heat onto the glass top.
• Do not use large pots or heavy weights that can bend the pan support or deflect flame onto the glass top.
• Locate pan centrally over the burner so that it is stable and does not overhang the appliance.
• Use only a wok support supplied or recommended by the manufacturer of the appliance.

Models and parts of the gas hob

Table 1 – a) Nozzle (Injector) and burner characteristics for LPG / G30 gas at 30 mbar

Type of the burners| Normal heat input

(kW)

| Outer ring Ø injectors

（mm）

| Inner ring Ø injectors

（mm）

---|---|---|---
Ultra-rapid| 5.0| 0.98| 0.48
Semi-rapid| 2.3| 0.75| –
Auxiliary| 1.0| 0.50| –

Table 1 – b) Nozzle (Injector) and burner characteristics for Town gas / G110 gas at 10 mbar

Type of the burners| Normal heat input

(kW)

| Outer ring Ø injectors

（mm）

| Inner ring Ø injectors

（mm）

---|---|---|---
Ultra-rapid| 3.8| 2.4| 1.1
Semi-rapid| 2.3| 2.0| –
Auxiliary| 1.1| 1.45| –

How to use the gas hob

Gas burners
The gas flow to the burner can be regulated by turning the corresponding control knob to one of the following positions. (see Fig.1)

Gas burners
The gas flow to the burner can be regulated by turning the corresponding control knob to one of the following positions. (see Fig.1)

• OFF (close valve)
• High (maximum aperture or flow)
• Low (minimum aperture or flow)

The size of flame depends on the position of the related burner control knob .

The burner should be set at large flame during the initial phase of the cooking to allow quick heating of the cooking contents. After quick heating, turn the control knob to small flame for slow warming of food or maintaining heating conditions. Other flame adjustment can be achieved by positioning the indicator between the large flame and small flame. Never adjust the flame size between the large flame and OFF position.

Igniting the burners

The appliance is equipped with automatic ignition system and flame failure safety device. To ignite the burner, carry out the following steps:

• Press and turn the corresponding control knob anti-clockwise to the large flame position. The gas burner will be ignited.
• At this position, hold down the control knob for 5 seconds to allow the flame to heat up the thermocouple.
• Then, release the knob and the flame shall be remained lighted up.
• Turn the control knob to achieve the flame as desired.
• If the flame can’t be lighted, turn the control knob clockwise to the off position. Then repeat step a to c.
• After cooking is completed, turn the control knob clockwise to the off position.

Battery Ignition

The automatic ignition system is powered by a 1.5 V battery. If the automatic ignition does not work, check the battery compartment under the gas hob to ensure that the battery is positioned correctly. Replace the battery if necessary (see Fig.9 in page 9).

Selection of burners and diameters of pan

• On the control panel, near every knob, there is a diagram to indicate the burner controlled by the corresponding knob. Select the burner in accordance to the diameter of the pan used and the heat input.

The recommended burners for the flat bottom pan diameters are as follow :

It is important that the diameter of the pan is suitable to the heat input of the burner. During usage, adjustment of the control knob is required to ensure that the flame does not extend out from the bottom of the pan.(see Fig.2 )

Correct use of Ultra-rapid burner

To use the wok, you need to position the wok directly onto the center of the pan support. Recommended wok top’s open diameter shall not exceed 36 cm. For gas hob models without Auxiliary, while using the flat-bottomed pan with a diameter of less than 12 cm, you need to position the mini trivet (Fig.3) provided onto the pan support. After lighting the burner, adjust the control knob so that the flame length do not extend out from the bottom of the pan so as to prevent overheating of the panhandle (see Fig.2 in page 5).

Flame failure safety device

This gas hob is equipped with flame failure safety device. In the event, the flame is accidently extinguished, the supply of gas to that burner will be shut off. Before re-lighting the burner, turn off the burner control knob and do not attempt to re-ignite the burner for at least one minute.

Burner Head

Ultra-rapid

1. THERMOCOUPLE
2. SPARK
3. INNER CAP
4. OUTER RING CAP
5. LARGE BURNER CUP
6. VENTURI
7. AUXILIARY BURNER CAP
8. AUXILIARY BURNER CUP

Note: The coating of the burner caps and burner cups might decolorize or peel off after the appliance is used. However, this will not affect the performance of the appliance

Cleaning and maintenance

• Cleaning and maintenance should be carried out only after the appliance has turned cold, especially when cleaning the burner and the cast iron support. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the hob surface. Avoid using acid or chlorine-based cleaning products
• After cleaning the burners and the caps they must be well-dried and put back correctly. It is very important to check that the burner cups F, burner cap A, and cap B has been correctly positioned (Fig.6)-failure to do so can cause serious problem.
• As shown by the arrow, the “M” positioning of the inner cap cover must be aligned with the “m” clamping position of the burner cup, and the “N” positioning of the inner cap cover must be aligned with the “n” clamping position of the burner cup (as shown on the left side of Fig.6). The burner should not rotate in its correct position.

How to place the pan support

In order to prevent the pan support from rotating, there is a special positioning support. During installation, make sure that the special positioning support is placed exactly on the groove of the spill tray (Fig. 7 ).

Check that the ignition electrode “S” (Fig.8) is always clean to ensure trouble-free sparking. Check that the probe or thermocouple “T” (Fig.8) is always clean to ensure the correct operation of the safety valves. Both the ignition electrode and the thermocouple must be very carefully cleaned .

Caution:
Special care should be taken to the lower surface of the appliance as this area is not designed or intended to be touched. It also may contain sharp or rough edges, that may cause injury. For safety, always wear a pair of rubber gloves while cleaning.

To extend the life of the cooktop, please make sure that the appliance are cleaned carefully and thoroughly on a frequent basis, keeping following in mind:

• SURFACE OF ENAMEL PARTS
  All of the Enamel parts must be washed only with a sponge and soapy water or non-abrasive products.

• STAINLESS STEEL SURFACES
  Stainless steel can be stained if it remains in contact with highly calcareous water or aggressive detergent (containing phosphorous) for an extended period of time. Stainless steel parts must be rinsed with water and dried with a soft and clean cloth, it is also recommended to clean up any spills as soon as possible.

• PAINTED PARTS AND SILKSCREEN PRINTED SURFACES
  Clean using an appropriate product. Always dry thoroughly. These parts must be cleaned very carefully to avoid scratching and abrasion.

• BURNERS AND PAN SUPPORT
  These parts can be removed and cleaned with appropriate products.

Cleaning the Wok Burner

The burner cup must always be kept clean. While cleaning the burners, remove the burner caps and use a cotton bud, toothbrush or some other items to clean out any incrustations or dirt from area marked as “H” in Fig.4. This procedure is necessary to ensure correct the functioning of the burner. Clean the burner caps using needle or toothbrush to remove the dirt and carbon, blocking the burner holes. (Fig.5)

Note : Regular use may cause discoloring around the burners due to the high temperature of the flame.

General advice

• When the appliance is not being used, it is advised to keep the gas regulator or TG supply level closed.
• The gas hob requires regular maintenance by a qualified technicians for its reliable operation. We recommend the gas hob maintenance to be carried out at least once in every 18 months.

Installing the battery

Insert a DC1.5V dry battery into the battery compartment (see below Fig.9) in the cover. This dry battery is the power supply for the electronic ignition of gas burners.

Notes for battery installation or replacement:

• Only use a DC1.5V dry battery (size “58*38” mm).
• Check for correct polarity ( label to the side of the battery compartment ).
• Do not use an Alkaline battery.

Important notes:

• Remove the battery if the hob is not going to be used for a long time.
• If the battery becomes weak or leaks, replace it immediately.
• Avoid touching the leaked liquid and make sure it does not come into contact with clothes or other items.
• Clean the battery compartment carefully before installing the new one.
• The battery is a potential source of danger for children.
• Keep them away.
• Dispose the batteries properly.

Installation instructions

Important

• The appliance should be installed, regulated, and adapted to function with other types of gas by a qualified installation technician. Failure to comply with this condition will retain the guarantee validation.
• The appliance must be installed in compliance with regulations in force in your country and in observation of the manufacturer’s instructions.
• Some appliances are supplied with a protective film on steel and aluminum parts. This film must be removed before using the cooker.
• The appliances must be installed in heat-resistant units.
• The walls of the units should not be higher than the worktop and must be capable of resisting temperatures of 75℃ and above.
• Do not install the appliance near inflammable materials (eg. curtain).
• Incorrect installation, for which the manufacturer or distributor accepts no responsibility, may cause personal injury or damage.

Technical information

• The appliance is designed to be embedded into kitchen fixtures measuring 600 mm in depth.
• In order to install appliance into the kitchen fixture, a hole with the dimensions shown at the cutting size board (Fig.11 in page 11) has to be made, taking following into consideration:
• The distance, between the bottom of the cooktop and the upper surface of any other appliance or internal shelf must be at least 10-15 cm (Fig.13 in page 12).
• The cooker top must be kept no less than 200 mm away from any side wall.
• The hob must be installed at least 65mm away from the rear wall(Fig.10 in page 11). There must be a distance of at least 750 mm between the hob and any wall of the cupboard for extractor hood positioned immediately above (Fig.10 in page 11). It is essential to install a heat baffle between the bottom of the hob and the underlying unit.
• No conversion to different gases of another family is recommended, this appliance shall use the gas of the family that it is designed for and adjusted at factory.

Cut-out dimension & replacement size

Fixed gas hob position

Before putting the hob into the cut-out entrance, please stick the sponge strip around the glass panel and adjust the screws to match the size. After confirming the position of the gas hob, adjust the screws on the four sides of the bottom case to fix the gas hob on the cabinet. (Figure 12)

Installation of gas hob in kitchen cabinet with door

The cabinet has to be made in accordance to the specific requirements to ensure proper operation of the gas burners. When the flame is turned down to minimum, pressure changes due to opening and closing of the cabinet doors. The cabinet should have openings to facilitate ventilation (see Fig.13 & 14 ).

Installation of built-in oven under the gas hob

If there is a built-in oven set to be installed under gas hobs, it is required that a horizontal partition with high temperature resistant material is built in between the gas hob and built-in oven. The distance between the surface of this partition to the under surface of the gas hob must be at least 10-15cm to allow air circulation and protect the rubber gas tubing from the heat of the built-in oven (see Fig.15).

Ventilation requirement

• The appliance must be installed in compliance with applicable local regulations concerning ventilation and the evacuation of exhaust gases.
• Intensive and prolonged use may need additional ventilation, for example, opening of a window or to have a more efficient ventilation.

Choosing suitable surroundings

• The room where the gas appliance is to be installed must have a natural flow of air so that the gas can burn. The flow of air must come directly from one or more openings made in the out-side walls with a free area of at least 100cm².
• The openings should be closer to the floor and preferably far away from the product. The openings should also made sure that they are not blocked from inside or outside of the unit.
• When these openings cannot be made, the necessary air can come from an adjacent room which is ventilated as required, as long as it is not a bedroom or a dangerous area.
• In this case the kitchen door must allow the passage of the air.

Inlet gas connection

Important:

• The appliance should be installed, regulated and adapted to function with other types of gas by a qualified installation technician.
• The appliance is fitted with specified gas type as shown in the specification nameplate and cannot be used or converted to any other type of gas.

Installation

The appliance is predisposed and adjusted to operate with the gas indicated on the specifications nameplate located at the bottom of the appliance.
Please ensure that the intended gas type used corresponds with that specified on the nameplate.

Gas connection to the gas hob

• The appliance should be connected to the gas-supply by licensed installer. During installation of this appliance, it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing.
• Connection of the appliance to the gas mains or liquid gas must be carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable to the type of gas to be used. In the case of connection to liquid gas, by tank,use pressure regulators that conforms the regulation in force.
• Connection to the gas course must be done in such a way that there are no any stress points at any part of the appliance.

Important: For safety, and correct regulation of gas usages and long life of the appliance, ensure that the gas pressure conforms to the indications given in table 1 ‘Nozzle and burner characteristics’.

Gas leak test operation

After the gas pipe connection has been completed, the gas leak test must be performed before the installation is considered complete. After connecting to the mains, check that all the couplings are correctly sealed, using soap solution.
NEVER use a naked flame. If bubbles appear, please close the gas valve immediately and re-adjust the gas connection before re-testing the appliance Turn on the gas and ignite each burner. Check if the flame is blue without any yellow tipping. If there is an abnormal flame, turn off the flame and check that the burner cap is properly positioned and the correct gas type is used

Gas hob not functioning

In the event of any abnormal situations or malfunctions of the gas hob, do not attempt to rectify the situations or repair the gas hob. Contact the customer service center as mentioned in the warranty card for assistance. When contacting the customer service center, please provide the model number

Global Website
www.fujioh.com
FUJIOH INTERNATIONAL TRADING PTE.LTD
Southeast Asia Regional Headquarters
3014A Ubi Road 1 #06-04 SINGAPORE 408703
E-mail : fit@fujioh.com.sg
Tel: +(65) 6286 3286 Fax: +(65) 6285 3285
Rev1 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>