GHOST AXR1 3 Button Water Resistant Remote Transmitter Instructions
- June 13, 2024
- Ghost
Table of Contents
GHOST AXR1 3 Button Water Resistant Remote Transmitter
Product Information
The Water Resistant Remote is a 3-button remote transmitter designed to activate Gate 1 or Gate 2. It features an LED light and is water-resistant, making it suitable for outdoor use. The remote works in conjunction with the gate system controller, which has a Learn Remote mode for programming additional remotes. The remote uses GhostCodeTM signal technology to transmit commands to the gate controller.
Product Usage Instructions
Programming Remote to Gate Controller
- Press and hold the LEARN XMTR button on the gate system controller.
- While holding the LEARN XMTR button, press and hold either BUTTON 1 or BUTTON 2 on the remote for 2 seconds.
- Release the BUTTON 1 or BUTTON 2 on the remote.
- If the gate controller alarm sounds or the gate begins moving, the button on the remote has been successfully programmed into memory. The LED on the remote will turn on when the button is depressed.
Adding an Additional Remote Transmitter to Control the Gate
Note: This process assumes that Remote A (Training Remote) is already capable of controlling the gate.
- Press and hold the LEARN button on Remote B (Learning Remote) for at least 3 seconds.
- Press and hold either BUTTON 1 or BUTTON 2 on Remote A (Teaching Remote).
- Release the BUTTON 1 or BUTTON 2 on Remote A.
- Press and release either BUTTON 1 or BUTTON 2 on Remote B. The LED on Remote B will indicate that it is now programmed to operate the same gate as Remote A.
Cloning / Copying Button 1’s ID to Button 2’s (Button 1 Already Controls the Gate)
- Press and hold the LEARN button on the remote for at least 3 seconds until the LED on the remote stays on.
- Release the LEARN button. The remote is now in Learning Mode.
- Press and release Button 1 on the remote. The LED on the remote will start flashing rapidly, indicating that it is sending Button 1’s ID.
- Press and release Button 2 on the remote. The LED on the remote should go off, indicating that Button 1’s ID is now accepted by Button 2. Both buttons should now work the same gate.
Cloning / Copying Button 2’s ID to Button 1’s (Button 2 Already Controls the Gate)
Note: Follow the same steps as above, but reverse the roles of Button 1 and Button 2 in Steps 3 and 4.
INSTRUCTIONS
3-BUTTON WATER RESISTANT REMOTE TRANSMITTER PROGRAMMING AND REMOTE
TRANSMITTER OVERVIEW
All GHOST CONTROLS® remote transmitters must be programmed before they will
operate the Gate Opener System so that the safety and security of your system
is maintained.
OVERVIEW
NOTE:
REMOTES A & B MUST BE TOUCHING AND ORIENTED AS SHOWN TO PROGRAM REMOTE B FROM
REMOTE A
PROGRAMMING REMOTE TO GATE CONTROLLER
GENERATING A NEW TRANSMITTING KEY CODE
CAUTION
Please READ and PROCEED with CAUTION Each GHOST CONTROLS® remote transmitter
has a unique key code sequence. Once a new key sequence is generated, the
previous key code is lost. The new key code will need to be programmed or
“learned” into the gate opener to control the gate. See Programming Remote to
Gate Controller on front page.
ASSEMBLING THE UNIVERSAL CLAMP TO ATTACH TO YOUR REMOTE
(can be used on golf carts, tractors, motorcycle handlebars, and even mounted outside on a post)
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced technician for help
WARNING
- This product contains a Button or Coin Cell Battery.
- A swallowed Button or Coin Cell Battery can cause internal chemical burns in as little as two hours and lead to death.
- Dispose of used batteries immediately.
- Keep new and used batteries away from childern.
- If you think batteries might have been swallowed or placed inside any part of the body,seek immediate medical attention.
- WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov
- www.GhostControls.com
- Made in China, AXR1IM | REV 0223
©2023 GHOST CONTROLS®
Documents / Resources
|
GHOST AXR1 3 Button Water Resistant Remote
Transmitter
[pdf] Instructions
AXR1 3 Button Water Resistant Remote Transmitter, AXR1, 3 Button Water
Resistant Remote Transmitter, Water Resistant Remote Transmitter, Resistant
Remote Transmitter, Remote Transmitter
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>