TRADEQUIP 1198T Under Hoist Auxiliary Stand Owner’s Manual

June 6, 2024
TRADEQUIP

TRADEQUIP 1198T Under Hoist Auxiliary Stand - logo **1198T Under Hoist Auxiliary Stand

Owner’s Manual**TRADEQUIP 1198T Under Hoist Auxiliary
Stand

Specifications

  • Safe Working Capacity: 680kg
  • Minimum Height: 1370mm
  • Maximum height: 2045mm
  • Base Diameter: 300mm
  • Carton: 1390 x 370 x 90mm
  • Weight: 16.5kg

About the TradeQuip brand

The ‘TradeQuip’ brand of workshop equipment, is designed for use in a demanding workshop environment by professional users. With proven and trusted “Made for the Trade” reliability, ‘TradeQuip’ branded products offer the very best in performance for an affordable price. All backed by a 1year trade guarantee across 1,000+ distributors Australia-wide.

TRADEQUIP 1198T Under Hoist Auxiliary Stand - logo 3

WARNING INFORMATION

IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
WARNING
The instructions and warnings contained in this manual should be read and understood before using or operating this equipment.
Do not allow anyone to use or operate this equipment until they have read this manual and have developed a thorough understanding of how this equipment works. Failure to observe any of the instructions contained in the manual could result in severe personal injury to the user or bystanders, or cause damage to the equipment and property. Keep this manual in a convenient and safe place for future reference.
Whilst every effort has been made to ensure the accuracy of the information contained in this manual, the TradeQuip policy of continuous improvement determines the right to make modifications without prior warning.

STANDARD OPERATING PROCEDURE

DO NOT use this machine unless you have been trained and assessed to a competent level in its state use and operation, and have been given permission to use  this

| Safety glasses must be worn when operating this equipment
---|---
| Safety footwear must be worn when operating this equipment
| Rings and jewelry must not be worn when operating this equipment
| Long loose hair must be contained when operating this equipment
| Close-fitting/protective clothing must be worn when operating this equipment

SAFETY CHECKS

PRE-OPERATIONAL SAFETY CHECKS

  • Check vehicle owner’s manual for correct component weight – DO NOT exceed parts stands’ safe working capacity.
  • Use only for partial support of vehicle components during removal and installation
  • Use only as specified by the manufacturer.
  • Do not use this stand to support or stabilize a vehicle.
  • Use only on a hard, level surface.
  • Securely support the vehicle before placing parts stands in place.
  • Place component in the center of the saddle.
  • For your safety, do not modify or alter these auxiliary parts stands.
  • Use the right product for the job. There are certain applications for which the stand was designed. Do not modify the Stand and do not use the stand for a purpose for which it was not intended.

INTENDED USE
For or partial support of vehicle components during removal and installation of components

ASSEMBLY, OPERATION & PREVENTATIVE MAINTENANCE

  1. FEATURES
    TradeQuip Auxiliary Parts Stands are intended to be used as a means of partial support and the positioning of vehicle components during their installation/removal. The Auxiliary Parts Stand is not for use in stabilizing or supporting vehicles.
    These are for use under a 2 or 4 post overhead vehicle lift or in a garage pit. Heavy gauge steel construction to ensure safety, strength, and stability.

  2. ASSEMBLY
    1. Insert the smaller end of the threaded column through the bottom of the upright, allowing the small end of the threaded column to project out of the top of the upright.
    2. Place bearing over threaded portion with upright/threaded column assembly in the horizontal position.
    3. Spin adjusting handle clockwise onto threaded portion.
    4. Insert the roll pin through the saddle & thread column to fasten the saddle.
    5. Insert upright assembly onto the base with a slot in upright facing foot pedal mount.
    6. Secure upright using the larger pin, washer, and r-clip.
    7. Insert pedal into the slot and secure with retaining pin, washer, and r-clip.

  3. BEFORE USE
    Conduct a thorough visual inspection checking for any abnormal conditions, such as cracked welds, and damaged, loose, or missing parts.

  4. OPERATION
    Prior to each use always conduct a visual inspection checking for any abnormal conditions, such as cracked welds, and damaged, loose, or missing parts.
    To Raise:
    • Turn adjusting handle clockwise until saddle contacts load. Be sure to center load on saddle.
    • Slight upward adjustments can be made to the saddle height by pressing downward on the foot pedal.
    • This may or may not be necessary depending on the application. It is provided as a means of making temporary adjustments on load height without using your hands. This leaves your hands free to engage, handle and control the workpiece.
    WARNING
    • The stands must be positioned on a hard level (concrete) surface.
    • The safe working load must not be exceeded under any circumstances.
    • DO NOT lower overhead lift in order to accommodate load on the stand.
    • Contact with the desired vehicle component shall only be done by means of the vertical adjustments provided on the stand.
    • Always center the component load on the saddle.
    To Lower Vehicle:
    • Turn adjusting handle counterclockwise
    • Carefully remove the stand from underneath the vehicle.
    • Slowly lower vehicle to the ground with overhead lift hoist control

  5. STORAGE
    These Jack Stands should always be stored in a dry indoor location in the upright position.

  6. MAINTENANCE
    Periodically inspect each stand. Ensure all parts move freely. Do not apply oil or grease to any part of this product. If rust appears, sand the affected area and cover it with suitable paint. This product has no replacement parts.

  7. SERVICE & REPAIR
    Any Auxiliary Parts Stands found damaged in any way, or found to be worn or operating abnormally should be removed from service until repaired by an authorized service agent. Owners and/or operators should be aware that repair of this product may require specialized equipment and knowledge. Only authorized parts, labels, decals shall be used on this equipment.
    An annual inspection of the Jack Stands is recommended and can be made by an authorized repair facility to ensure that your equipment is in optimum condition and that the equipment has the correct decals and safety labels specified by the manufacturer.?
    Product Code: 1198T

PARTS DIAGRAM & LIST

TRADEQUIP 1198T Under Hoist Auxiliary Stand - figure 1

Part It| Description| CITY| Part #| Description| QTY
---|---|---|---|---|---
1| Lifting Screw| 1| 8| Flat Washer 16| 2
2| Spring 6×26| 1| 9| Clevis Pin with Head 16×70| 1
3| Handle| 1| 10| Clevis Pin with Head 12×35| 1
4| Handle Sleeve| 2| 11| Flat Washer 12| 2
5| Bearing| 1| 12| Base| 1
6| Upright Column| 1| 13| Foot Bar| 1
7| Pedal Lever| 1| 14| “R” Clip| 2

WARRANTY

TradeQuip products have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship for a period of 12 months from the date of purchase except where tools are hired out when the guarantee period is ninety days from the date of purchase.

Should the machine develop any fault, please return the complete tool to your nearest authorized warranty repair agent or contact TQB Brands Pty Ltd Warranty team – warranty@tqbbrands.com.au.

If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs will be carried out free of charge. This guarantee does not apply to normal wear and tear, nor does it cover any damage caused by misuse, careless or unsafe handling, alterations, accident, or repairs attempted or made by any person other than the authorized TQB Brands Pty Ltd repair agent.

This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorized.
Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the 12 month period.
Consumer Guarantee
Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

TRADEQUIP 1198T Under Hoist Auxiliary Stand - figure 2

All images and illustrations shown are for reference purposes only. All information, specifications and illustrations in this manual are based on the latest information available at the time of publication and are subject to change without notice. The information in this manual is periodically revised to ensure the latest information is included. Download the latest version of this manual and other related technical documentation from www.tqbbrands.com.au.

Made in China to TQB Brands Pty Ltd Specifications
Visit us atwww.tqbbrands.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals