Litokam B0CQ2RVV83 Video Doorbell Camera Wireless with Chime Ringer Instruction Manual

Litokam B0CQ2RVV83 Video Doorbell Camera Wireless with Chime Ringer

Doorbell Overview

• Video doorbell

• Chime

• User’s Manual

• Doorbell disassembly needle

• USB Power cord

• Wire jumper

• AC Power extension cord

• Screw Hole Positioning Card

• Double Sided Tape

• Doorbell Bracket

• Screw pack

Doorbell indicator status

Introduction to the use of doorbell buttons

Doorbell Network Settings

Note :

• After receiving the doorbell, please use the included charging cable to fully charge the doorbell.
  
  The doorbell battery has slight deviations due to different usage. Normally, the doorbell records 10 events per day, and each event is recorded for 15 seconds.
  Under these conditions, the doorbell can last up to 6 months when fully charged.

• Scan the code, download and install the “Littlelf Smart” APP, and use your email address to register an account;
  |
  ---|---
  

• Connect your mobile phone to a 2.4GHz Wi-Fi network.

• After the doorbell is fully charged, long press the Power Button for 3 seconds to turn it on. During the process of turning on the doorbell, the LED indicator will slowly flash blue and have a “Device Power on” prompt message.

• When the doorbell plays the “Ready to connect” prompt message, you can start to configure the network for the doorbell. If the doorbell does not play this prompt, please long press the Power Button for 5 seconds to restore the factory settings.

You can refer to the following ways to set the doorbell:

A. Quickly configure the network for the doorbell

1. Log in to the “Littlelf Smart” APP, turn on the Bluetooth on your mobile phone, and grant the corresponding permission to the “Littlelf Smart” APP.
   

2. Click the “Add” button in the dialog box. If the dialog box does not pop up, you can click the”+” icon or “Add Device” button on the home page, and the doorbell will be searched; then click the “+” icon at the end of the doorbell to add.
   

3. Enter WI-Fl password and click “Next” (Doorbell only supports 2.4GHz).

4. Wait for the doorbell to automatically complete network configuration and click “Done”.
   

B. Configure doorbell network using QR code

1. On the home page of Littlelf Smart APP, click the “+” or “Add Device” button.

2. Select doorbell type “01 “.

3. Confirm the doorbell indicator status and click “Next”.
   

4. Enter WI-Fl password and click “Next” (Doorbell only supports 2.4GHz).

5. Aim the QR code generated on the phone screen at the camera (from 15-20cm away). After hearing “Scan code success”, click “Hear the beep” .

6. Wait for the doorbell to automatically complete network configuration and click “Done”.
   

Chime configuration

1. In the device list interface, click the doorbell “D1” to enter the doorbell live broadcast interface, select Settings/Chime Settings/Connect Chime. Select “Connect” in the dialog box that is displayed.
   

2. Plug the Chime into the socket, and it will automatically turn on with a start bell and its indicator will flash white. Select “Hear the Chime Ring and indicator will flash white ” and click “Next”. If the Chime does not flash white light, please long press the Ring Button on the Chime for 5 seconds until it rings.

3. Press the “Doorbell” button on the doorbell, when you hear the Chime ring, select “Hear the Chime Ring”, and click the “Send Pairing Code” button.

4. Press the “Doorbell” button on the doorbell again to confirm whether the Chime rings; if it rings, click “Done” to complete the pairing. If the Chime does not ring, click “Chime does not ring” and make the match again according to the prompt.
   

Storage Methods

There are two options for video storage:

A. Cloud storage

You can follow the steps below to subscribe to the cloud storage package. After enabling the cloud storage function, the doorbell will automatically save the video to the cloud, so that you can view the video record anytime and anywhere.

B. SD Card storage (local storage)
An SD Card is required for local storage. Insert the SD Card as shown in the following figure. After the doorbell identifies the SD Card, the recorded video will be stored in the SD Card.

Doorbell Mounting

• If you don’t have a wired doorbell, or you don’t want to install this doorbell in your existing doorbell location, please refer to the installation steps of “Battery Powered”.
• If you want to install this doorbell at an existing doorbell location, please refer to the installation steps of “Using the Existing Doorbell Wires to Power the Doorbell”. (Note: Doorbell required voltage: 8-24V AC).

Select the doorbell mounting spot
Place the doorbell where you want to install it and view the live image via the “Little’ll smart” App in order to find the best mounting spot for the doorbell.

Consider the following factors when installing the doorbell:

• Check whether existing holes in walls or door frames can be reused.
• If you want to put the doorbell close to the wall, make sure that the wall side will not appear in the monitoring field of view. Otherwise, infrared mode (night vision mode) and infrared light refracted multiple times may cause a blurred night vision effect.
• It is recommended that the doorbell be installed at a height of 48″/1.2m from the ground to reduce the monitoring blind area between the ground and the corner.
• If you want to use the doorbell to monitor your packages, it is recommended to place the package rack 0.5 meters away from the wall. (The package detection function needs to be purchased for an additional fee.)
  

Method 1: Battery-powered installation steps

Install doorbell bracket
A. If you want to mount the doorbell on a wooden surface (door frame), you don’t need to pre-drill holes. Use a screwdriver to tighten the screws to secure the doorbell bracket to the mounting spot.

What is required: screwdriver, screw (included) , doorbell bracket.

B. If you want to mount the doorbell on a hard material surface, such as brick, concrete, or stucco, please follow the steps below:

• Paste the positioning card to the doorbell mounting spot.
• Use a 15/64″ (6 mm) drill bit to drill holes according to the screw holes on the positioning card.
• Insert the anchors into the holes, then use a screwdriver to tighten the screws to secure the doorbell bracket to the mounting spot.
  

What is required: electric drill, 6mm drill bit, doorbell bracket, screw pack, Screw Hole Positioning Card

Mount the doorbell on the doorbell bracket
Align the bottom of the doorbell with the fixed position on the bracket and press the top until it clicks into place.

Doorbell mounting completed.
Note: Before mounting the doorbell, please complete the network configuration for the doorbell and keep the doorbell on.

Detach the doorbell from doorbell bracket
If you want to remove or charge the doorbell, please refer to the following steps:
Insert the doorbell disassembly needle into the removal hole above the doorbell, and press down firmly; the doorbell will automatically pop out of the bracket and then you can remove the doorbell.
What is required: doorbell disassembly needle

Method 2: Installation steps for powering a doorbell using the existing doorbell wires:

Check whether the existing doorbell wires are working properly.

• Press the doorbell button of the existing doorbell to check whether it is working properly. If the doorbell does not ring, the doorbell power wires may be defective.
  Please install your new doorbell using the battery-power method or consult an electrician to repair the wiring.

• If the doorbell rings properly, shut off the power to the existing doorbell on the circuit breaker.
  

Note:

• The voltage required for the doorbell: 8-24V AC, please confirm that the existing doorbell wires meet this requirement; if your existing doorbell has an 8V power supply, use the provided “jumper cable” to connect the two terminals in your existing doorbells’ chime.
  

• Be careful when handling wires during the installation process. If you’re not comfortable installing it yourself, have an electrician do it.

Detach the existing doorbell
Use a screwdriver to detach the existing doorbell. When detaching the existing doorbell, pay attention to the power wires on the back of it.

• Remove the power wires from the back of the doorbell using a screwdriver;
• Check whether the power wires are damaged or aging.
  What is required: screwdriver
  

Install doorbell bracket
A. If you want to mount the doorbell on a wooden surface (door frame), you don’t need to pre-drill holes. Use a screwdriver to tighten the screws to secure the doorbell bracket to the mounting spot.

What is required: screwdriver, screw (included) , doorbell bracket.

B. If you want to mount the doorbell on a hard material surface, such as brick, concrete, or stucco, please follow the steps below:

• Paste the positioning card to the doorbell mounting spot.
• Use a 15/64″ (6 mm) drill bit to drill holes according to the screw holes on the positioning card.
• Insert the anchors into the holes, then use a screwdriver to tighten the screws to secure the doorbell bracket to the mounting spot.t
  

What is required: electric drill, 6mm drill bit, doorbell bracket, screw pack, Screw Hole Positioning Card

Connect the doorbell wires
Connect the wire on the wall to the power port on the back of the doorbell, and tighten the screw. The doorbell AC power terminals do not distinguish between positive and negative poles and can be connected in any order.

Note:

• The doorbell AC power terminals do not distinguish between positive and negative poles and can be connected in any order.
• To prevent short-circuits, make sure the positive and negative poles of the wires are not touching each other.
• If the wires are too short, use the extension wires and wire nuts provided to make them longer. Use electrical wiring tape instead if there is no more space on the wall for wire nuts.
  

What is required: screwdriver, video doorbell and AC power extension cord.

Mount the doorbell on the doorbell bracket
Align the bottom of the doorbell with the fixed position on the bracket and press the top until it clicks into place.

Doorbell mounting completed.
Note: Before mounting the doorbell, please complete the network configuration for the doorbell and keep the doorbell on.

Turn on the doorbell power switch on the circuit breaker

Through the Littlelf Smart APP, turn on the doorbell monitoring screen to confirm whether the doorbell is charging. If it is displayed on charge, the doorbell installation is completed; If not, check the power wires.

Common Problem

Q1: The doorbell doesn’t turn on

1. Long press the doorbell Power Button for 3 seconds and make sure that the Power Button is pressed.
2. Use the Type-C USB cable to charge the doorbell, wait about 3 minutes, and check whether the LED indicator on the doorbell is green. If the LED indicator on the doorbell is in solid green, it means that the doorbell battery is insufficient and cannot be turned on, please fully charge the doorbell. If the LED indicator on the doorbell has not been lit, please try to use another Type-C USB cable or charger to charge it; the charger needs to support 5V/1.5A.
3. Put the doorbell indoors before pressing the power button to turn it on to avoid the doorbell failing to turn on due to the low outdoor temperature. Doorbell operating temperature is -4 °F to 122°F/-20°C to 50°C.

Q2: Doorbell network configuration failed.
If the doorbell indicator flashes blue and the doorbell sounds “Ready to connect” after being turned on, the doorbell can normally configure the network. If the doorbell indicator flashes in other forms, please troubleshoot the doorbell as follows:

1. Restore factory settings for the doorbell. (Reset method: long press the Power Button for 5 seconds when powered on).
2. Unplug the USB charging cable, the indicator will flash green when the doorbell is charging.
3. Check whether the router password is correct. (Wi-Fi password, not APP account password).
4. Check whether the Wi-Fi signal of your router is 2.4 GHz. If your router is set up to share a Wi-Fi account for 2.4 GHz and 5 GHz, please configure 2.4GHz and 5GHz network accounts for your router respectively (For how to set up the router, refer to the router manual).
5. Check that the Wi-Fi connected to the phone is 2.4 GHz.

Q3: Littlelf Smart APP home page shows doorbell offline.

1. Adjust the position of the router to ensure that the router signal is strong and stable at the location where the doorbell is installed.
2. Confirm that the Wi-Fi signal from the router can access the network normally.

Technical Specifications

Doorbell
Operating temperature-20°C-50°C, Operating humidity 10%-95°/o No condensation.
Notice: The maximum normal condition operating temperature is defined as +50°C except battery charging conditions. The maximum battery charger temperature is defined as 45°C.
Frequency Range: 2.412-2.4 72 GHz, RF Output Power: 17 .5 dBm
Power: 8-24V~ 50/60Hz 50mA Or 5V 1A

Chime
Operating Temperature-10°C to 45°C;
Operating Humidity <90% at 40°C;
Power: 100-240V – 50/60Hz;
Symbol means alternating current Indoor use, bathroom excluded; Symbol means for indoor use only Symbol means Class II product-Double Insulated -No earth required.

Notification of Compliance

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferencE to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
  Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

CE EU Declaration of Conformity
Litokam declares that the doorbell is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

This product must not be disposed of as normal household waste, in accordance with EU directive for waste electrical and electronic equipment (WEEE- 2012/19/EU).
Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point. The device could be used with a separation distance of 20cm to the human body.

ISED Statementst
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Litokam Customer Care

For additional support, please refer to the following resources:

FAQs and Guide Video: available on the Littlelf Smart app or official website. (Scan the code on the right side for quick access)

Online Customer Service
Available via app, telephone, and website during the following hours:
PT 08:00-10:00/17:30-20:00/21 :30-08:00

Littlelf Smart APP Live chat
Website: www.litokam.com
 Tel: US&Canada Toll Free PT 1 (866)722-6296 (Mon-Sun: 11 :00 AM- 6:30 PM)
Email: support@litokam.com

Follow us on social media: @Litokam

Please note the following warranty terms:

1. 30-day return policy and 12-month limited warranty.
2. Lifetime professional tech support provided by Litokam.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>