Philio PAT14 Z-Wave Ultra Low Temperature Sensor User Manual
- June 6, 2024
- Philio
Table of Contents
- Z-Wave Ultra low temperature sensor PAT14
- Specification
- Troubleshooting
- Installation Steps
- LED Light Indication
- Z-Wave™ Multi Channel Association
- Z-Wave™ Notification
- Z-Wave™ Message Report
- Over The Air (OTA) Firmware Update
- Z-Wave Configuration Settings
- Z-Wave Supported Command Class
- Choosing a Suitable Location
- Disposal
- FCC Interference Statement
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Philio PAT14 Z-Wave Ultra Low Temperature Sensor
Z-Wave Ultra low temperature sensor PAT14
The Z-Wave Ultra low temperature sensor PAT14 has 2 channel thermocouple , based on Z-Wave™ technology. This device is a security enabled Z-Wave
Plus™ product. The encrypted Z-Wave Plus™ messages support PAT14 to communicate with other Z-Wave Plus™ products. PAT14 can be used with Z-Wave™ devices (with Z-Wave™ logo) from different manufacturers, it can also be included in the Z-Wave™ networks from different manufacturers.
All mains operated nodes (even from different manufacturers) in the network act as repeaters to increase the stability and reliability of the ZWave™ network.
The product is supported with Over-the-Air (OTA) feature for firmware upgrade.
Specification
Rated | DC5-24V 6mA |
---|---|
RF distance | Min. 40M indoor, 100M outdoor line of sight |
RF Frequency | 868.40 MHz, 869.85 MHz(EU) 908.40 MHz, 916.00 MHz(US) 920.9MHz, |
921.7MHz, 923.1MHz(TW/SG/Thai/KR)
RF Maximum Power| +10dBm (Peak), -10dBm (Average)
Dimension| 47.5 x 39 x16 mm
Location| Indoor use only
Operation temperature| -10°C – 40°C
Storage Temperature| -20°C – 60°C
Humidity| Up to 85% max
Temperature Detect Range| -250 to 300°C
Sensor type| External K/J/T type thermocouple (depend on the user choice)
FCC ID| RHHPAT14
Specifications are subject to change and improvement without notice.
Troubleshooting
Symptom
| Cause of Failure|
Recommendation
---|---|---
The device can not join to Z-Wave™ network
| The device may in a ZWave™ network.|
Exclude the device then include again.
Installation Steps
- Connect 5-24V&GND to 5-24VDC.
- Connect K/J/T Type Thermocouple to CH1/CH2.
***When installing a thermocouple, please pay attention to the positive and
negative polarity of the thermocouple. If the installation is wrong, the
temperature measurement will be wrong.
For Instruction tohttp://www.philio-tech.com
Add to/Remove from Z-Wave™ Network
There is a button with LED indicator in front of PAT14. It is used to dim on/off the light and carry out the inclusion, exclusion, reset or association of PAT14 from Z-wave controller.
When the fist power one, the LED indicator flashes once per second for 30 seconds. With the SmartStart function, PAT14 will be automatically included by Z-wave controller.
PAT14 can be operated with any certified Z-Wave™ devices from different manufacturers in Z-Wave™ network. All non-battery operating devices act as repeaters to increase the stability and reliability of the ZWave™ network.
The table below provides an operation summary of basic Z-Wave™ functions. To add/remove/associate PAT14, please refer to the instruction of certified Z-Wave™ Primary Controller.
Function | Description |
---|---|
Without Node ID | New PAT14 does not have Node ID until it is included by a |
Z-Wave™ Controller.
Add (Classic Inclusion)|
- Set Z-Wave™ Controller to inclusion mode by fol- lowing the instructions provided by the controller manufacturer.
- Press the button on PAT14 three times within 3 sec- onds to enter inclusion mode.
SmartStart|
-
To initiate the SmartSart process, please type in the first five digits of DSK string or scan the QR code. The QR Code can be found on PAD15 or in the box.
Ex: DSK: 18112-24021-58001-62259-57092- 27453-08187-47408 -
PAT14 is supported with SmartStart, it can be added to Z-Wave™ network by scanning the Z- Wave™ QR code on the product.
-
Without further actions, PAT14 will be automatically included in a certified Z-Wave™ Controller with SmartStart inclusion ability in 10 minutes after it turned on.
Remove (Exclusion)
|
- Set your Z-Wave™ controller to exclusion mode by following the instructions provided by the controller manufacturer.
- Press the button on PAT14 three times within 3 sec- onds to enter exclusion mode.
- Node ID will be excluded.
Reset| 1. Press the button of PAT14 four times within 3 sec- onds and hold the last press until the LED light turns off.
- Adding a node ID allocated by Z-Wave™ Controller means inclusion. Removing a node ID allocated by Z-Wave™ Controller means exclusion.
- The situation of including/excluding of the node ID can be checked from the Z-Wave™ Controller.
- Function Reset: The Reset procedure can only be used when PAD15 cannot be recognized by the Z-Wave™ Primary Controller.
Notice 1: Always RESET a Z-Wave™ device before trying to add it to a Z-Wave™ network
LED Light Indication
The LED light indicates the different modes of the PAD15
State Type | LED Indication |
---|---|
Without Node ID | Under normal operation, when the PAD15 has not been allocated |
a node ID, the LED light will flash on and off alternately at 1-second
intervals. By pressing the On/Off button, LED light will stop flashing
temporarily.
Learning| Flashes when learning is successful
Z-Wave™ Multi Channel Association
PAT14 just be set to send reports to multi channel associated ZWave™ devices. It supports five association groups with five nodes support for group 1 ~ group 5.
Group 1, the will report DEVICE_RESET_LOCALLY_NOTIFICATION.
Group 2, End Point 1 will report ( channel 1) SENSOR_MULTILEVEL_REPORT_TEMPERATURE
Group 3, End Point 2 will report ( channel 2) SENSOR_MULTILEVEL_REPORT_TEMPERATURE
Group 4, End Point 1 will report (channel 1) NOTIFICATION_REPORT_HEAT_V4
Group 5, End Point 2 will report (channel 2) NOTIFICATION_REPORT_HEAT_V4
Z-Wave™ Notification
This function default is disable, to enable this function by setting the configuration NO.3 bit4~7.And set threshold by setting the configuration NO.11 ~ 14.
Z-Wave™ Message Report
- Temperature differential report:
This function default is enabled, to disable this function by setting the configuration NO.7 to 0.
In the default, when the temperature is changed to plus or minus 0.5 degree Celsius, the device will report temperature information to the nodes in the lifeline group.
The device will measure the temperature in every 1 seconds. And if the temperature is over 140 degree Fahrenheit (60 degree Celsius), the device will always report in each measurement.
* Timing Report:
The device support the timing unsolicited report of the status.
- Temperature report: Every 1 hours report once in default.
It could be changed by setting the configuration NO. 5.
Notice: The configuration NO. 5 could be setting to zero to disable the auto report. And the configuration NO. 6 could change the tick interval, the default value is 12, if setting to 1, that means the minimum auto report interval will be one minute. And please notice if setting this value to zero, that means disable all of the timing report except the low battery detection.
Over The Air (OTA) Firmware Update
The device support the Z-Wave firmware update via OTA.
Let the controller into the firmware update mode, and then press the tamper
key once to start the update.
At that time, please don’t remove the battery, otherwise it will cause the
firmware broken, and the device will no function.
After the LED stop flash, it is recommended that the user power up the device.
Caution: After remove the battery, please wait about 30 seconds, and then
re-install the battery.
Z-Wave Configuration Settings
Notice:
- All of the configuration, the data size is 1.
- The configuration mark with star(*), means after the remove the setting still keep, don’t reset to factory default. Unless the user execute the “RESET” procedure.
- The reserve bit or not supported bit is allowed any value, but no effect.
NO. | Name | Def. | Valid | Description |
---|---|---|---|---|
1 | Operation Mode | All | Bit control. | |
0 | Bit0 : reserve. | |||
0 | Bit1 : reserve. | |||
0 | Bit2 : reserve. | |||
1 | Bit3 : Set temperature unit. 0: Fahrenheit 1: Celsius | |||
0 | Bit4 : CH1 overheat notification 0:disable 1:enable | |||
0 | Bit5 : CH1 under heat notification 0:disable 1:enable | |||
0 | Bit6 : CH2 overheat notification 0:disable 1:enable | |||
0 | Bit7 : CH2under heat notification 0:disable 1:enable | |||
2 | Custom Func | All | Bit control. | |
01 | Bit0 、 Bit1 : Set CH1 thermocouple type |
00 → disable,01 → K-type 10 → T-type,11 → J-type
0| | Bit2 : reserve.
00| | Bit3 、 Bit4 : Set CH2 thermocouple type
00 → disable,01 → K-type 10 → T-type,11 → J-type
0| | Bit5 : reserve.
0| | Bit6 : reserve.
0| | Bit7 : reserve.
3| Auto Report Temperat ure Time|
5
| 0 ~ 127| Temperaturn auto report time 0 : disable.
Default is 5. Tick Interval can setting by configuration No.4.
4| Auto Report Tick Interval| 12| 0 ~ 0xFF| The interval time for auto report
each tick. Setting this configuration will effect configuration No.3.
Units of one minute. Caution1:
Setting to 0 means turn off all auto report function.
Caution2: The value is unsigned byte, the range is from 0x00 ~ 0xFF.
5| Temperat ure Differenti al Report| 0| 0 ~ 127| The temperature differential
to report.
0 means turn off this function. The unit is Celsius.
And when the temperature is over 140 degree Fahrenheit, it will continue
report.
6| CH1
Temperat ure High threshold| 32767| int16| CH1 overheat notification
threshold.
7| CH1
Temperat ure Low threshold| -32768| int16| CH1 underheat notification
threshold.
8| CH2| 32767| int16| CH2 overheat notification threshold.
| Temperat ure High threshold| | |
9| CH2
Temperat ure Low threshold| -32768| int16| CH2 underheat notification
threshold.
Z-Wave Supported Command Class
Command Class | Version | Required Security Class |
---|---|---|
Z-Wave Plus Info | 2 | None |
Transport Service | 2 | None |
Security 0 | 1 | None |
Security 2 | 1 | None |
Supervision | 1 | None |
Version | 3 | Highest granted Security Class |
Configuration | 4 | Highest granted Security Class |
Association | 2 | Highest granted Security Class |
Association Group Info | 3 | Highest granted Security Class |
Notification | 8 | Highest granted Security Class |
Version | 3 | Highest granted Security Class |
Device Reset Locally | 1 | Highest granted Security Class |
Indicator | 3 | Highest granted Security Class |
Powerlevel | 1 | Highest granted Security Class |
Multi Channel | 4 | Highest granted Security Class |
Firmware Update Meta Data | 5 | Highest granted Security Class |
Multilevel Sensor | 2 | Highest granted Security Class |
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
Choosing a Suitable Location
- The suitable ambient temperature for the module/device is -10°C~40°C.
- Do NOT place the module/device direct under sunlight, in a humid place or in any location where they may contact moisture, dirt, dust.
- Do NOT place the module/device where exists combustible substances or any source of heat, fires, radiators, boiler etc.
Disposal
| This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
---|---
Philio Technology Corporation
8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City 24257, Taiwan(R.O.C) www.philio-tech.com
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Warning
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities. Contact your local government for information
regarding the collection systems available. If electrical appliances are
disposed of in landfills or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new once, the retailer is legally obligated
to take back your old appliance for disposal at least for free of charge.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>