Philio V1-H Single Color LED Dimmer User Manual

Single Color LED Dimmer
Model No.: V1-H
DC12-48V/Step-less dimming/Wireless remote control/Push Dim/Wall junction box mounting

Features

• 4096 levels 0-100% dimming smoothly without any flash.
• Match with RF 2.4G single zone or multiple zones dimming remote control.
• One RF controller accepts up to 10 remote control.
• Auto-transmitting function: Controller automatically transmits a signal to another controller with a 30m control distance.
• Synchronize on multiple controllers.
• Connect with external push switch to achieve on/off and 0-100% dimming function.
• Light on/off fade time 3s selectable.
• Easy to be placed in a standard wall junction box behind a push switch.

Technical Parameters

Input and Output

(12V/24V/36V/48V)
Output type| Constant voltage

Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED

Environment

Dimming data

Warranty and Protection

Weight

Mechanical Structures and Installations

Typical Wall Junction Box Mounting

Wiring Diagram

• Match with dimming remote

• Connect with the push switch

Match Remote Control (two-match ways)

End-user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key
Match:
Short press the match key, immediately press the on/off key (single-zone remote) or zone key (multiple zones remote) on the remote.
The LED indicator fast flash a few times means the match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart
Match:
Switch off the power, then switch on the power, and repeat again.
An immediately short press the on/off key (single-zone remote) or zone key (multiple zones remote) 3 times on the remote.
The light blinks 3 times means the match is successful.

Delete:
Switch off the power, then switch on the power, and repeat again.
An immediately short press the on/off key (single-zone remote) or zone key (multiple zones remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.

Application notes

1. All the receivers are in the same zone. Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be extended.
   Auto-synchronization: Multiple receivers within a 30m distance can work synchronously when they are controlled by the same remote.
   Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range.
   Strong signal sources such as WiFi routers and microwave ovens will affect the range.
   We recommend for indoor applications that receiver placements should be no further apart than15m.

2. Each receiver(one or more) is in a different zone, like zone 1, 2, 3, or 4.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.

• Short press:
  Turn on or off the light.

• Long press (1-6s):
  Press and hold to step-less dimming,
  With every other long press, the light level goes in the opposite direction.

• Dimming memory:
  Light returns to the previous dimming level when switched off and on again, even at power failure.

• Synchronization:
  If more than one controller is connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
  This means there is no need for any additional synchrony wire in larger installations.
  We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from the push to the controller should be no more than 20 meters.

Dimming curve

Logarithmic dimming curve

Light on/off fade time

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>