Philio R8S 10-Key 8 Scene RF Remote Controller User Manual
- June 5, 2024
- Philio
Table of Contents
10-Key 8 Scene RF Remote Controller
Model No.: R8S
8 scene/10-key/Wireless remote 30m distance/CR2032 battery/Magnet stuck
fix
Features
- 8 scene RF 2.4G remote.
- Apply to a single color, dual color, RGB, RGBW, or RGB+CCT RF LED controller.
- Each remote can match one or more receivers.
- RC 2032 attery powered.
- Operate with LED indicator light.
- Magnet on the back which can be easily stuck on back holder or any metal surfaces.
Technical Parameters
Input and Output
Output signal| RF (2.4GHz)
Working voltage| 3VDC (CR2032)
Working current| <5mA
Standby current| <2μA
Standby time| 2 years
Remote distance| 30m(Barrier-free space)
Environment
Operation temperature| Ta: -30 ºC ~ +55 ºC
IP rating| IP20
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED
Warranty
Warranty| 5 years
Weight
Gross weight| 0.040kg
Net weight| 0.064kg
Mechanical Structures and Installations
To fix the remote, three options are offered for selection:
Option 1: stuck the remote on any metal surfaces directly.
Option 2: fix the remote’ back holder on the wall with two screws.
Option 3: adhere the remote’ back holder to the wall with a paster.
Match Remote Control (two-match ways)
End-user can choose the suitable match/delete ways. Two options are offered
for selection:
Use the controller’s Match key
Match:
Short press the match key, and immediately press the ON key on the remote.
The LED indicator fast flash a few times means the match is successful.
Delete:
Press and hold the match key for 5s to delete all matches,
The LED indicator fast flash a few times means all matched remotes were
deleted.| Use Power Restart
Match:
Switch off the power, then switch on the power, and repeat again.
Immediately short press the ON key 3 times on the remote.
The light blinks 3 times means the match is successful.
Delete:
Switch off the power, then switch on the power, and repeat again.
Immediately short press the ON key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
---|---
Key function
ON:
Turn on the last scene light.
OFF:
Turn off the last scene light.
Scene 1-8:
Recall the scene saved in the RF controller.
Note:
The remote only has a scene recall function default.
If you want to use the scene save function, please long press ON + S8 key 2s
to enable the scene save function, then long-press Scene 1-8 key 2s to save
the current color into this scene number. the LED indicator will light up
longer when save OK.
When all 8 scenes save OK, please long press OFF + S8 key 2s to disable the
scene save function.
Safety information
-
Read all instructions carefully before you begin this installation.
-
When installing the battery, pay attention to the battery’s positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. -
If no response from the receiver, please re-match the remote.
-
Gently handle the remote, beware of falling.
-
For indoor and dry location use only.
User Manual Ver 1.0.0
R8S 10-Key 8 Scene RF Remote Controller
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>