Angler BI-45W-RL 14 Inch LED Bi-Color Ring Light and Light Stand Instructions

June 6, 2024
angler

Angler BI-45W-RL 14 Inch LED Bi-Color Ring Light and Light Stand

Instructions

Thank you for choosing Angler.

The Angler BI-45W-RL is a 14-inch ring light that’s ideal for lighting vlogs and interviews, and self-lighting influencer videos and home broadcasts. Its bi-color SMD LEDs are housed in a diffuser that softens and spreads the beam for a flattering single-shadow light that’s bright and color accurate.
This ring light runs on battery or AC power so it’s as effective in the field as it is in the office or at home. Color temperature adjustment from 2700 to 5600 K lets you light subjects with the warmth of a tungsten
bulb, bright daylight, and everything in between. Create realistic lighting or match the ambient light of your environment. For convenient setup wherever you want to record or chat, a four-section light stand is
included with height adjustment from 16 to 58.5 inches. The included flex arm with a spring-loaded smartphone clamp puts your phone at the center of the action. The light is designed with shoe and 1/4-20 accessory mounts.

Precautions

Please read and follow these instructions, and keep this manual in a safe place.
Keep this unit away from water and any flammable gases or liquids.
Do not leave the device in a closed vehicle under the sun or in other areas subject to very high temperatures.
Do not attempt to disassemble or repair the equipment. There are high-voltage components inside the unit. Failure to observe this pre- caution could result in electric shock or product malfunction. This will void the warranty, and Angler will not be responsible for any damage.
Use only the correct, recommended voltage.
Make sure the unit is powered off when plugging it into a power source. Disconnect the power cord when not in use.
Use only parts provided by the manufacturer. Handle this product with care.
Clean this product with only a soft, dry cloth. Keep this unit away from children.
Make sure the item is intact and that there are no missing parts. All images are for illustrative purposes only.

Overview

Remote Control

Setting Up the Light Stand

  1. Loosen the leg lock, and unfold the legs to the desired angle. Tighten the leg lock until secure. Important! Set the legs at a wide enough angle to ensure stability of the ring light and attached camera or accessories.
  2. Loosen the center column locking knobs and adjust the stand to the desired height. Tighten the locking knobs until secure.

Packing Up the Light Stand

  1. Loosen the locking knobs and collapse  the sections to the minimum height.
  2. Loosen the leg lock and fold the legs up so they’re parallel to the shaft.

Mounting the BI-45W-RL

  1. Loosen the locking knob, and place the receiver onto the light stand’s 5/8-inch pin.

  2. Make sure the receiver fits completely over the pin before you tighten the locking knob. If it doesn’t, continue to loosen the locking knob until the fixture drops down around the pin.

  3.  Tighten the locking knob until the ring light is secure.

Powering On the Light

AC Power

When operating the light on AC power, remove the batteries.

  1. Plug the power adapter into the light, and plug the power cord into an available outlet. OFF will appear on the control screen to indicate the light is receiving power.
  2. Press the Power/Brightness knob. Adjust the brightness and color temperature knobs to desired setting.

Battery Power

A 7.4 V NP-F type battery is recommended for the BI-45W-RL ring light.
When operating the light on battery power, unplug the power adapter from the light.

  1. Place an NP-F battery into the  battery plate, and slide it toward the contacts until locked in place. OFF will appear on the control screen to indicate the light is receiving power.

  2. Press the Power/Brightness knob. The battery display in the LED screen will show the remaining battery charge in 25% increments.

    When the bottom red LED is the only illuminated light, the battery is low and should be recharged or replaced. To remove the battery, press the battery release button, and slide the battery out of the battery compartment.

Adjusting the Color Temperature and Brightness

Color Temperature

Turn the color temperature knob to adjust the color temperature from 2700 to 5600 K in 100 K increments.

Brightness

Turn the dimmer knob to adjust the output level from 0% to 100% in 1% increments

Using the Memory Function

When you power on the light, it will resume operation with the color temperature and brightness that are set in the memory. To set the memory function, follow these steps. Color Temperature

  1. Turn the color temperature knob to set the color temperature.
  2. Press and hold the color temperature knob until the color temperature display blinks. The color temperature is now set in the memory.

Brightness

  1. Turn the brightness knob to set the light’s output.
  2. Press and hold the knob until the brightness display blinks. The brightness is now set in the memory.
  3. When you release the knob, the light will power down. Press the Power/Brightness knob again to resume operation.

Attaching a Smartphone

  1. Insert the phone into the pring-loaded clamp.

  2. Attach the flex arm smartphone holder to the shoe mount by sliding it into the shoe and tightening the locking wheel.

  3. Loosen the locking knob at the base of the phone clamp, and adjust the phone’s orientation. Then tighten the locking knob until secure.

Adding Accessories

Use the 1/4-20 threaded socket and the shoe mount to add small photo and video accessories.

Remote Operation

The included remote uses an infrared beam to operate the ring light. For remote operation, line of sight is required, and the maximum range is approximately 50 feet.

Power Button

Press the power button to turn on the ring light. The light will power up with the most recent color temperature and brightness settings.

Press again to power off the light.

Daylight Button

Pressing the daylight button sets the light to 5600 K daylight-balance color temperature at 100% brightness.

Auto Buttons

Use the Auto Buttons to automatically set the light to a warm, neutral, or cool color temperature at either 100% or 50%
brightness. Press again to power off the light

Brightness Up/Down

The brightness control lets you adjust the light’s brightness from 0% to 100% in 1% increments.

Color Temperature Control

The color temperature control adjusts the color temperature from 2700 to 5600 K in 100 K increments.

Save Button

To save the current brightness and color temperature, press and hold the save button until the display blinks. The light will recall these settings the next time it’s powered up. You can also press the save button at any time to recall the settings.
Note: Any subsequent setting adjustments made manually will override these stored settings

Recycling Lithium-Ion Batteries

Lithium-ion batteries are recyclable. You can help preserve the environment by returning your used rechargeable batteries to a collection and recycling location near you.
For more information about recycling rechargeable batteries, call the Call2Recycle helpline at 1-877-723-1297, or visit www.call2recycle.org.

Specifications

LIGHT FIXTURE

LED CHIP TYPE| SMD
COLOR TEMPERATURE| 2700 TO 5600 K
COLOR ACCURACY| CRI: 98 (3200 K) / 96 (4400 K) / 98 (5600 K)
STANDARD| TLCI: 98 (3200 K) / 98 (4400 K) / 98 (5600 K)
COOLING SYSTEM| PASSIVE
DIMMING| YES, 0% TO 100%
DISPLAY| LED
HOUSING MATERIAL| ABS PLASTIC
| 3200 K: 666 LX
LIGHT INTENSITY @3 FT.| 4400 K: 1120 LX
| 5600 K: 782 LX
EXPECTED LAMP LIFE| 50,000 HR.
DIAMETER| 14 IN. (36 CM)
DIMENSIONS (H × D)| 17.25 × 1.4 IN. (43.8 × 3.5 CM)
WEIGHT| 1.2 LB. (0.5 Kg)
LIgHT STAND

STAND TYPE| GENERAL PURPOSE STAND
NUMBER OF SECTIONS| 4
MAXIMUM WORkING HEIGHT| 60 IN. (152.4 CM)
MINIMUM HEIGHT| 15.7 IN. (39.9 CM)
TOP MOUNT| 5/8 IN. STUD wITH 1/4-20 MALE THREAD
MOUNTING

FIXTURE MOUNT| 5/8 IN.
TILT| +/– 90°
CONNECTORS

BATTERY PLATE| NP-F
POWER INPUT CONNECTOR| BARREL
POWER OUTPUT CONNECTOR| USB STANDARD-A
REMOTE OPERATION

REMOTE CONTROL TYPE| PROPRIETARY
FREqUENCY| IR
POWER

AC INPUT POWER| 100 TO 240 V AC, 50/60 Hz
DC INPUT POWER| 7.4 V DC
POWER SOURCE| AC ADAPTER, NP-F BATTERY
MAX POWER CONSUMPTION| 45 W
USB OUTPUT POWER| 5 V, 2 A
SMARTPHONE BRACKET

MAXIMUM WIDTH| 3.25 IN. (8.2 CM)
LENGTH| 8.5 IN. (21.6 CM)

One-Year Limited Warranty

This Angler product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.

This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Angler Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Angler along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals