Shenzhen Isunbom Technology ET-CW02 Magnetic Car Wireless Charger Instruction Manual

ET.CWO02
MAGNETIC CAR WIRELESS CHARGER
Instruction Manual

Thank you for choosing to buy our wireless equipment Charging products. ET.CWO2 is a magnetic car wireless Charger. zinc alloy body, 2.5D PMMA lens, instant charging, magnet positioning. higher and taster charging efficiency. Different charging experience for you to enjoy wireless technology! Can support Qi standard mobile phones, Before using the product. please read this Operate the manual carefully and keep it in a safe place for inspection.

Attention

1. please use qualified DC power adapter, otherwise, it may cause instability,
2. do not put metal debris or card in the charging plate, may be caused charge damage or abnormal.
3. use of the process if the receiver coil or the launch plate is encountered overheating led to stopCharging, Please take down the equipment in harge, after coding, retry to charge.

Safety notice

• Do not pull on the cord hard to avoid power line break or fall off.
• Do not disassemble or put ET.CW02 into fire, water, avoid making Short circuit leakage.
• Do not use the ETCWO02 in the severe high temperature, wet or corrosive environment, to avoid the leakage of the circuit leakage phenomenon.

Technical Specifications

FAQ

1. the phone is not charging?
   The phone is not aligned with the charging sensing area or the receiving coil is not properly installed.

2. the charge of fever?
   Wireless charging process reserves the cod or the transmitter board appears as a normal phenomenon.

3. mobile phone charging interrupted?
   • DC charging head (adapter) charging current is not enough or voltage is not stable, please use the 5V-2A 9V-1.67A, 12V-2A adapter.
   • The charging position is too biased, the electromagnetic induction is not good, can adjust the charging position.

4. the host indicator is normal, but the phone can not work?
   Mobile phone receiving cod failure, it is recommended to update the receiving coil or repair the phone. (internal receiving coil)

5. the charge is relatively slow?
   Mobile phone itself or external receiving coil to allow the size of the wireless charging current is not same, or when the phone is charging standby power consumption, it is recommended to reduce cell phone standby program, or the adapter did not reach 5V-2A,9V-1.67A,12V-2A, please select the formal adapter. (other questions, please contact the after-sales service directly)

Product assembly drawing

Air Outle Device Method

FCC Statement
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and any other radio device.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>