TSI 7585 Q-Trak XP Indoor Air Quality Monitor User Guide
- June 6, 2024
- tsi
Table of Contents
- TSI 7585 Q-Trak XP Indoor Air Quality Monitor
- Unpacking and Parts Identification
- Installation of Gas Sensors
- Providing Power to the Q-Trak™ XP Monitor
- Installing the Wi-Fi® Dongle (optional)
- Charging the Battery and Calibrating the Power Gauge
- Operating the Instrument with the AC Adapter
- Powering ON the Q-Trak™ XP IAQ Monitor
- Main Menu
- Select Settings to setup the following: **Manuals, Software, and Other
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TSI 7585 Q-Trak XP Indoor Air Quality Monitor
Thank you for purchasing a TSI® Incorporated (TSI®)
Q-Trak™ XP Indoor Air Quality (IAQ) Monitor. This guide
will help you quickly begin using your monitor.
More detailed information is in the Operation Manual located on the included
Q-Trak™ XP USB Flash Drive. Please refer to the manual if you have questions
on the operation of your new monitor.
Safety
Refer to the Q-Trak™ XP Indoor Air Quality Monitor
Mode 7585 user manual for safety information.
WARNING
The instrument must be used in the manner described in the user manual.
Failure to follow all of the procedures described in the manual can result in
serious injury to you or can cause irrevocable damage to the instrument.
Unpacking and Parts Identification
Carefully unpack the instrument and accessories from the shipping container. Check the individual parts against the list of components below. If anything is missing or damaged, notify TSI® immediately. All standard equipment can be purchased separately if needed.
Installation of Gas Sensors
In addition to the standard built-in sensors, the device can accept up to six
gas sensors.
Install the gas sensors as follows:
-
Ensure the instrument is powered OFF.
-
Remove the sensor module cover.
-
Position the sensor as shown, making certain the pins make good contact with the device.
Gas sensors can be installed in any available slot.Listen for a click to confirm sensor is connected properly. -
Attach the cover to the sensor module.
Providing Power to the Q-Trak™ XP Monitor
The Q-Trak™ XP monitor can be powered with the lithium-ion battery or with the A/C adapter.
Operating the Instrument with the Lithium-Ion Battery
The lithium-ion battery must be installed by the user and fully charged before
use. Install the battery:
- Remove the battery compartment cover.
- Connect the battery to the handle connector.
- Insert the battery as shown in the picture below, keeping the battery wires to the side and clear of the battery cover screw.
Installing the Wi-Fi® Dongle (optional)
If purchased, install the dongle into the USB port located inside the battery compartment.
Attach the battery compartment cover, ensuring battery wires are clear of the
screw.
IMPORTANT Calibrate the battery power gauge
Charging the Battery and Calibrating the Power Gauge
- With the battery installed, turn on the instrument by pressing the power button and run until the battery is fully discharged. The instrument will automatically turn off when the battery is fully discharged.
- Connect the AC adapter to the instrument and fully charge the battery. This may take up to 3 hours. Note the lightning bolt indicator when charging vs fully charged.
- The instrument is now ready for use with the battery. This Power Gauge calibration procedure does not need to be repeated unless the battery is replaced or disconnected.
Operating the Instrument with the AC Adapter
The instrument can be operated with or without a battery using the A/C
adapter.
To operate the instrument with AC adapter:
- Plug the AC adapter into an electrical outlet.
- Plug the other end into the instrument.
Powering ON the Q-Trak™ XP IAQ Monitor
- Press and release the power button . In 35 seconds the instrument is ready for use.
- The first time the Q-Trak™ XP monitor is powered ON the Welcome to Q-TrakTM XP page is presented.
Select the appropriate Language and Time Zone then select DONE.
After selecting DONE, the Dashboard page is displayed in Survey mode.
Main Menu
To display the Main Menu, select the icon in the upper left corner of the header on any page of the display.
Select Settings to setup the following: **Manuals, Software, and Other
Resources**
• User Manuals, App Notes, and other resources are available for download at
www.tsi.com/7585, click on the “Resources” tab.
• TrakPro™ Ultra Software is available at: https://tsi.com/support/tsi-
software-and-firmware/ and enters the search term Q-Trak XP.
TSI Incorporated – Visit our website www.tsi.com for more information.
- USA Tel: +1 800 680 1220
- UK Tel: +44 149 4 459200
- France Tel: +33 1 41 19 21 99
- Germany Tel: +49 241 523030
- India Tel: +91 80 67877200
- China Tel: +86 10 8219 7688
- Singapore Tel: +65 6595 6388
P/N 6013908 Rev. C (US, FR, DE, CN, CN-T) ©2021 TSI Incorporated Printed in U.S.A.
References
- Home | TSI
- Q-Trak XP Indoor Air Quality IAQ Monitor 7585 | TSI
- TSI Software And Firmware Wizard | TSI
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>