BONECO F220CC/ F230CC Air Shower Fan and Purifier User Manual

BONECO F220CC/ F230CC Air Shower Fan and Purifier

TECHNICAL DATA

Technical data|
---|---
Model| | BONECO F220CC – BONECO F230CC
Power supply voltage| | 120V ~ 60Hz
Power consumption| | 36 W (max. level)
Operation noise level| | 60 dBA (max. level)
Air flow| | 530 cfm (900 m³ / h)
CADR| | Dust 110 cfm (187 m³/h)
| | Smoke 122 cfm (207 m³/h)
| | Pollen 116 cfm (197 m³/h)
Dimensions L×W×H| BONECO F220CC| 14.8 × 14.8 × 33.5 in (375 × 375 × 850 mm) with one connector piece
| BONECO F230CC| 14.8 × 14.8 × 47.6 in (375 × 375 × 1210 mm) with two connector pieces
Weight (empty)| BONECO F220CC| 17.6 lbs / 8 kg
| BONECO F230CC| 27.6 lbs / 12.5 kg

• Subject to change

INTRODUCTION

DEAR CUSTOMER

Congratulations on your purchase of the BONECO “Clean & Cool” Fan. These high- performance units seamlessly adapt to your needs. On any level they provide a high air purification function and a pleasant cooling breeze of cleaned air. This is possible thanks to the HEPA-ESP Filter and UV-C light. The perfect solution for healthy air. In developing the BONECO “Clean & Cool” Fan, we focused on creating the optimal combination of fan and purifier. This was possible thanks to the integration of the state of the art BONECO HEPA-ESP filter into our high performance Fans.

We hope you enjoy your new BONECO “Clean & Cool” Fan!

ITEMS INCLUDED

• BONECO fan unit
• Removable connector piece
  • (F220CC: 1×/ F230CC: 2×)
• Base with power cord
• HEPA-ESP filter
• Manual
• Safety instructions

OVERVIEW AND PART NAMES

• BONECO F220CC “Clean & Cool” Fan

• BONECO F230CC “Clean & Cool” Fan

1. Output regulator
2. Fan unit
3. HEPA-ESP filter
4. Button for unlocking
5. Removable connector piece
6. Base with power cord

START-UP

1. Only place the base on a stable, level surface.
2. Insert the connector piece into the base.
3. Set the fan unit onto the connector piece.
4. Remove the HEPA-ESP Filter from its separate packaging.
5. Remove the back-grid of the fan unit.
6. Set the filter into the device.
7. Push it in until you feel a noticeable click.
8. Close the fan unit again with the back grid.
9. Plug the power cord into a power outlet.
10. Adjust the output using the control.

• Make sure to set the grid correctly as the device will otherwise not turn on.
• Please note that when turning on the fan for the first time or after it has not been used for some time you might hear a slight crackling noise for the first few minutes. This is the HEPA-ESP filter gaining an electrical charge which allows it to function as a highly efficient air filter.
•  BONECO F220CC and BONECO F230CC are only differentin that the BONECO F230CC includes a second connector piece.
• You can use the fan unit with one, with a second or without connector pieces. It can be customized to your needs.

HANDLING

HANDLING

All BONECO “Clean & Cool” Fans are designed for easy handling. The output is adjusted in four levels using a single control: 0 › I › II › III › IV.

ALIGNMENT

• The fan unit can be manually tilted 270 degrees.
• Warning: The fan unit does not rotate a full 360 degrees.

HEIGHT ADJUSTMENT

• All electrical components are completely integrated in the connector. Therefore, you can adjust the height at any time by adding connector pieces or by pulling them off after pressing down the button to unlock them.
• Warning: For safety reasons, a maximum of two connector pieces can be used at once for the BONECO F230CC and a maximum of one for the BONECO F220CC.

POSITIONING TIPS

NOTES ON OUTPUT

All BONECO “Clean & Cool” Fans are equipped with a high-performance fan that can move large amounts of air. Making use of this feature: Guide the air in a specific direction to achieve an uniform room climate. The following examples illustrate how to do this.

AIR-CONDITIONING SYSTEM (AC)

An air conditioner distributes temperature in various ways. Use the BONECO “Clean & Cool” Fan to move the warm air towards the air-conditioning system. This can0 be done directly or indirectly via air circulation, as shown in this image.

FRESH AIR

The BONECO “Clean & Cool” Fan helps you achieve better ventilation indoors. If cross-ventilation is not created, guide fresh air directly from the window into the desired room.

MULTIPLE FLOORS

In the summer, it can become hot and muggy on the upper floors. The powerful BONECO “Clean & Cool” Fan directs the cool air from the ground floor to multiple floors achieving a uniform temperature.

ROOMS WITH HIGH CEILINGS

In air-conditioned rooms with high ceilings, the cold air sinks to the floor while the warm air rises to the ceiling. Turn the BONECO Fan straight up for an air-shower sensation.

CLEANING THE HEPA-ESP FILTER

REMOVING THE FILTER

1. Make sure the device is unplugged.
2. Tilt the fan downwards and remove the back grid.
3. Use both hands to push in the locking mechanism of the HEPA-ESP filter lightly so it can be removed from the device.

CLEANING BY HAND

1. Use PH-neutral detergent (10 g / 1000 ml) in 40 °C water to wash.
2. After washing, rinse with clean water, and dry with a clean soft cloth.
3. Leave the filter in dry place for at least 5 hours to make sure it is completely dry before putting it back into the fan unit.

CLEANING BY DISHWASHER

• Do not wash the Filter together with dishes or materials containing fat and grease.
• Only use PH-neutral cleaning detergents suitable for your dishwashing machine.
• Set the cleaning temperature not higher than 70 °C.
• Only wash for one wash cycle and for no longer than 2 hours (including the drying).

1. Put the Filter into the dishwashing machine.
2. Take out the filter from the dishwashing machine, and check for damages or deformations to the Filter. Do not reinsert a damaged Filter into the device.
3. After washing always check if the filter is completely dry. If necessary, leave the filter in a dry place for up to 5 hours to ensure it can completely dry before reinserting it into the fan.
4. Always let the filter cool down to room temperature before putting back into the fan unit.

REINSERTING THE FILTER

1. Reinsert the filter until the locking mechanism has clicked in securing the filter in the device.
2. Close the fan unit again with the back grid. Make sure the back grid is set it correctly as the device will otherwise not turn on.

TROUBLE SHOOTING

With regular use, the filter should be cleaned at least once every 2 weeks. After some time without cleaning, the filter can give off a continuous clicking noise. When that happens it is necessary to clean the filter according to the cleaning instructions.

CLEANING

SAFETY INSTRUCTIONS

• Always unplug the BONECO “Clean & Cool” Fan before you begin cleaning! Failure to do so can result in electric shock and fatal injury!
• Do not use alcohol or corrosive cleaning agents for cleaning.

CLEANING THE HOUSING

• All BONECO “Clean & Cool” Fans are designed for lowmaintenance operation, even after years of use. In most cases, a dry cloth can be used for cleaning.
• If stubborn dirt is present, clean the housing using a damp cloth. Add a small amount of dishwashing detergent to the water.

CLEANING THE FAN BLADES

1. Tilt the fan unit upwards and loosen the safety screw.
2. Remove the front grill by turning it counterclockwise slightly.
3. Loosen the safety screw in the middle clockwise.
4. Remove the fan blades and clean them with a damp cloth.
5. Put the unit back together by following the steps in reverse order.
6. When reattaching the front grid with the screw, pay attention to the position of the two half-circle marks on the front and make sure they form a full circle.

DISASSEMBLY AND STORAGE

• WARNING: Please note that the removable connector pieces are detachable. When moving the unit to a new location, disassemble the unit into the detachable parts, transport the individual parts to the desired location, and then reassemble.
• ATTENTION: Storage is easiest and most efficient when you use the original packaging. Store the BONECO “Clean & Cool Fan” in a dry place.

1. Unplug the power cord from the power outlet.
2. Press the release button on the upper connector piece.
3. Remove the fan by pulling firmly upwards.
4. Press the release button on the upper connector piece.
5. Remove all connectors by pulling firmly.

www.boneco.us

BONECO is a registered trademark of BONECO AG, Switzerland

BONECO North America Corp., 15821 Ventura Blvd, Encino, CA 91436

References

• BONECO AG - humidifier, air washer, air purifiers and Air Shower fans - Boneco

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>