milwaukee M18 FVC45L Wet and Dry Vacuum Cleaner Instruction Manual

M18 FVC45L Wet and Dry Vacuum Cleaner
Instruction Manual OPERATOR’S MANUAL
Cat. No.
M18 FVC34L, M18 FVC45L
M18 FUEL™ 34L Wet/Dry Vacuum
M18 FUEL™ 45L Wet/Dry Vacuum

Original instructions
WARNING
To reduce the risk of injury, user must read and understand operator’s manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING
WHEN USING AN ELECTRICAL VACUUM, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING VACUUM. BEFORE USING THE VACUUM, READ THIS OPERATOR’S MANUAL, BATTERY PACK AND CHARGER OPERATOR’S MANUALS, AND ALL LABELS ON THE VACUUM, BATTERY PACK, AND CHARGER. FAILURE TO FOLLOW THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS INJURY.

GENERAL DESCRIPTION

• This appliance is not intended for use by persons (Including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

WORK AREA SAFET

• Keep work area clean and well ilt. Cluttered or dark areas invite accidents.
• Vacuums have motors and other parts that can produce sparks during normal use. Do not use within 30 feet of areas where explosive materials may be present (such as petrol pumps and places where liquids like paint thinners, cleaners, solvents, etc. are stored).
• Do not use In the presence of explosive dust, liquids or vapors.
• Do not use where oxygen or anesthetics are used.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use extra care when using on stairs.

ELECTRICAL SAFETY

• Do not handle battery packs or vacuum with wet hands.

PERSONAL SAFETY

• STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum when you are tired, distracted or under the influence of drugs, alcohol or medication causing diminished control.
• The operation of a vacuum can result In foreign objects being blown into eyes, which can result in eye damage Always wear safety goggles or glasses with side shields when operating vacuum.
• Wear a dust mask or use a suitable dust extraction solution when working in dusty situations. Dust particles can harm your lungs.
• Avoid accidental starting. Ensure the switch is In the off-position before Inserting battery pack. Inserting battery pack in vacuum that has the switch on invites accidents. -Do not overreach. Keep proper footing and bal-ance at all times. This enables better control of the vacuum in unexpected situations.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carry-ing the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

VACUUM USE AND CARE

• Do not use without dust cannister and/or filter In place.
• Do not use to pick up flammable or combustible liquids such as petrol or use in areas where they may be present.
• Do not pick up anything that is burning or smok-ing such as cigarettes, matches, or hot ashes.
• Do not pick up soot, cement, plaster or drywall dust without filter in place. These are very fine particles that may affect the performance of the motor or be exhausted back into the air. This product Is suitable for collection of silica dust when used In accordance with these instructions. To reduce the risk of health hazards from other vapours or dust, do not vacuum carcinogenic, toxic or hazardous materials such as asbestos, arsenic, barium, beryllium, lead,. pesticides or other health endangered materials.
• Use special care when emptying heavily loaded tanks.
• To avoid spontaneous combustion, empty dust box after each use.
• Do not leave vacuum unattended when battery pack is installed. Remove battery pack when not in use and before servicing.
• Disconnect the battery pack from the appliance before making any adjustments, changing ac-cessories, or storing appliance. Such preventive safety measures reduce the risk of starting the ap-pliance accidentally.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything else that may reduce air flow.
• Maintain vacuum. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the vacuum’s operation. It damaged, have the vacuum repaired before use. Many accidents are caused by poorly maintained tools.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack Is not In use, keep It away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. if contact ac-cidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is dam-aged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or tern perature above 130°C (265°F) may cause explosion.
• Follow all charging Instructionsand do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care.

SPECIFIC SAFETY RULES FOR WET/DRY VACUUM

• Never use vacuum without tank and filter prop-erly installed. ‘Wear ear protectors. Exposure to noise can cause hearing loss.

• This product is suitable for collection of silica dust when used in accordance with these in-structions.
  WARNING To reduce the risk of health hazards from other vapors or dust, do not vacuum car-cinogenic, toxic or hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangered materials. To reduce the risk of injury, when working in dusty situations, wear propriate respiratory protection or use a suitable dust extraction solution.

• Always use common sense and be cautious when using tools. It is not possible to anticipate every situation that could result in a dangerous outcome. Do not use this tool if you do not understand these operating instructions or you feel the work is beyond your capability:contact MILWAUKEE, Tool or a trained professional for additional information or training.

• Maintain labels and nameplates. These carry important information. If unreadable or missing. contact a MILWAUKEE’ service facility for a replacement.
  WARNING Some dust created by power sanding. sawing. grinding, drilling. and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other masonry products. and

• arsenic and chromium from chemically-treated lumber.
  Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventiated area. and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles.

READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE ADDITDNAL BATTERY SAFETY RULES

  WARNING To reduce the risk of fire, personal injury. and product damage due to a short circuit, never immerse your tool. battery pack a charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater. certain industrial chemicals, and bleach or bleach- containing products. etc.. can cause a short circuit.
WARNING Do not charge non-rechargeable batteries.

SYMBOLOGY

regulatory requirements.
****| Do not dispose of electric tools tother with household waste material. Electric tools and electronic  equipment that have reached the end of their He must be colected separately and retumed to an  environmentally compatible recycling facility.

FUNCTIONAL DESCRIPTION

Cat. no.: M18 FVCL34L

1. Large wet/dry vacuum
HEPA filter (4932479805)
2. Hose storage
3. Motor housing
4. Blower port (not shown)
5. Handle
6. Storage tie downs
7. Tank latches (front and back)
8. Dust bag holder
9. 34 litre wet/ dry vacuum tank| 10. Power switch
11. Hose storage clip
12. Vacuum inlet
13. Pedal
14. Wheel lock
15. Battery bays
16. Tank drain cap
17. Wet/dry vacuum cart
18. Utility nozzle
19. Extension wand
---|---

FUNCTIONAL DESCRIPTION
Cat. no.: M18 FVC45L

1. Large wet/dry vacuum
HEPA filter (4932479805)
2. Hose storage
3. Motor housing
4. Blower port (not shown)
5. Handle
6. Storage tie downs
7. Tank latches (front and back)
8. Dust bag holder
9. 45 litre wet/ dry vacuum tank| 10. Power switch
11. Hose storage clip
12. Vacuum inlet
13. Pedal
14. Wheel lock
15. Battery bays
16. Tank drain cap
17. Utility Nozzle
18. Premium Wet/Dry Vacuum Cart
19. Extension wand
20. Telescoping Handle
---|---

SPECIFICATIONS

Volts…………………………………………………… 36V DC
Battery Type ………………………………………….M18™
Recommended Ambient
Charger Type…………………………………………M18™
Operating Temperature …………………..-18° to 40°C
IP Rating………………………………………………….IPX4
Dust Class………………………………………….. L Class
Cat. No. ………………………………………. M18 FVC34L
Suction…………………………………………….. 192 mBar
Capacity …………………………………………………. 34L
Hose Size ………………………………. 27.6 mm (1-7/8″)
Weight………………………………………………….. 14 kg
Dimensions…………………………… 580x720x410 mm (510 mm with hose wrapped)
Cat. No. ……………………………………… M18 FVC45L
Suction…………………………………………….. 192 mBar
Hose Size ………………………………….. 63.5 mm (2.5″)
Capacity ………………………………………………….. 45L
Weight………………………………………………… 18.1 kg
Dimensions…………………………… 830x762x570 mm
*Litres indicated reflect drum volume, not necessarily collection capacity, actual capacity dependent upon type of debris collected, condition of filter and other factors. 34 Litre Wet/Dry Vacuum Tank included with M18 FVC34L only. 45 Litre Wet/Dry Vacuum Tank included with M18 FVC45L only.

ASSEMBLY

WARNING
To reduce the risk of injury, always remove the battery pack before removing the tank.
CAUTION
Keep filter clean. Efficiency of the vacuum is largely dependent on the filter. A dirty filter will reduce the air flow and overall efficiency of the system. Remove from tank and tap clean.
WARNING
Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
Inserting/ Removing the Battery
WARNING
Always remove the battery pack any time the tool is not in use. To insert the battery, slide the pack into the body of the tool. Make sure it latches securely into place.
To remove the battery, push in the release buttons and pull the battery pack away from the tool.
NOTICE
The vacuum/motor head requires two charged battery packs to operate.

• The vacuum/motor head will not work with only one battery pack.
• If one battery pack is completely depleted the vacuum/motor head will not function regardless if the other battery pack has capacity remaining.

Removing/Installing the Filters
Use the HEPA filter for dry pickup only. Use the foam filter for wet pick- up operation only.

1. Remove the battery pack.

2. Release the tank latches and lift off the motor housing. Place it upside down on a flat surface.

3. To remove the filter, turn counter clockwise and remove from the motor housing/float cage.

4. Empty all debris from the tank.
   NOTICE
   When applicable, adhere to jobsite guidelines pertaining to the disposal of silica dust.

5. To install the filter, slide it over the float cage. Line up the filter tabs with the motor housing notches and turn clockwise to lock in place.

6. Replace the motor housing and secure both latches.

WARNING
To reduce the risk of injury: wear safety glasses and a dustmask when using the vacuum cleaner as a blower.
Pick-Up/Blower
The vacuum can be used for debris pick-up or as a blower, depending on the port used.

1. For the debris pick-up, insert the large end of the hose into the intake port of the motor housing, lining up the tabs on the hose with the notches in the port. Twist to secure and form a tight fit.
2. To use as a blower, insert the large end of hose into the blower port of the motor housing, lining up the tabs on the hose with the notches in the port. Twist to secure and form a tight fit.

WARNING
Only use accessories specifically recommended for this tool. Others may be hazardous.
Attaching/Removing the Vacuum Cart

1. To attach, place rear of vacuum on the cart with the front angled upwards.The vacuum inlet should face the front of the cart where the pedal is located.

2. Slide the rear of the vacuum under the ledge feature.
   

3. Lower the front of the vacuum so it lines up with the cart and front ledge. Once the cart clicks, the vacuum is secured on the cart.

4. To remove, press one foot on the pedal. Lift the vacuum with handle away from the cart.

Installing/Removing the Accessories
To install the nozzles, hoses or extensions, push the accessory onto the vacuum hose inlet.
To remove the accessory, pull the accessory off the vacuum hose inlet.Store the accessories in the motor head or in the designated cart storage areas.
Installing/Removing the Dust Extraction Adapter
(Use Cat. No. 49902000 for M18 FVC34L and M18 FVC45L, not included)
The dust extractor hose adapter is used to connect the hose to a power tool in place of other dust collection, such as a dust bag.
To install the adapter, remove any nozzles or accessories from the end of the hose. Twist the adapter onto the hose until tight for a secure fit.
To remove, reverse the procedure.

OPERATION

WARNING To reduce the risk of injury, always wear proper eye protection marked to comply with AS/NZS 1337.1. When working in dusty situations, wear appro-priate respiratory protection or use a suitable dust extraction solution.
To reduce the risk of fire and injury, do not use to pick up flammable or combustible materials. To reduce the risk of injury, wear safety goggles or glasses with side shields. Empty tank before use. Before use, ensure the filter and float cage are properly installed. Remove dry filter before all wet pick-up operations.
Starting and Stopping Vacuum
To turn the vacuum on max runtime mode, push the power switch to the Speed One (I) position. To turn the vacuum on max power mode, push the power switch to the Speed Two (II) position.
To turn off the vacuum, push the power switch to the OFF (0) position.
CAUTION If the float is clean, moves freely, and the suction does not shut off when the tank is filled, contact a MILWAUKEE® service facility for repairs. A malfunctioning tool can cause personal injury or property damage.
Wet Pick-Up Operation
For wet pick-up operation, it is recommended to use the foam filter (Single pack, Cat. No. 49901990).

1. Remove the battery packs.
2. Remove ALL dirt and debris found in the tank.
3. Remove the high efficiency filter and install the foam filter (see “Removing/Installing the Filter”). Ensure that the float cage remains in place.
4. A float cage shuts off suction when the tank is full. Be sure that the float is clean and moves freely in the float cage to ensure that the float valve works.
5. Insert the battery packs.
6. Turn on the vacuum and begin pick-up.
7. Turn off the vacuum immediately upon completing a wet pick-up job or when tank is full and ready to be emptied. If suction shuts off , turn off the vacuum immediately and empty the tank.
8. Remove the battery packs.
9. To empty the tank, raise the hose to drain any excess liquid into the tank. Do not use vacuum inlet to drain contents.
10. Remove motor housing and pour liquid waste into a suitable drain.
11. Clean the interior of the tank and pick-up accessories periodically, more often when used to pick up wet, sticky materials. Use warm, soapy water. Do not store vacuum with liquid in tank.

Automatic Suction Shut-Off
When picking up liquids, an internal float rises until it seats itself against a seal at the intake of the motor, shutting off suction. When this happens, the motor will develop a higher than normal pitch noise and the suction is drastically reduced. If this occurs, turn off the vacuum immediately.
NOTICE Failure to turn off unit after float rises and shuts off suction will result in damage to the motor.
To continue use, empty the liquid waste from the tank.
If the vacuum is accidentally tipped over, it could lose suction. Turn off the vacuum and return it to an upright position. The float will return to its normal position.
Installing/Removing Fleece Dust Bag
For increased filter life and ease of cleanup, use a fleece dust bag to collect fine dust particles (Five packs, Cat. No. 49901989).

1. Remove the battery packs.

2. To install, release the tank latches and remove the motor housing.

3. Lift the dust bag holder up and out to remove from the tank.

4. Slide the cardboard dust bag inlet in to the dust bag holder.
   

5. Insert the dust bag holder back into the slot pushing downward to secure in place.

6. Spread out the dust bag in the tank. Replace the motor housing and secure both latches.

7. To remove, release the tank latches and remove motor housing.

8. Lift the dust bag holder up and out to remove from the tank.

9. Slide the dust bag holder off the dust bag.

10. Pull the cardboard tab until the dust bag inlet is closed. Dust bag is now sealed and can be properly disposed.

Replace fleece dust bag once the bag is at full capacity, suction decreases or dust bag is damaged.

Storage
Before storing your vacuum, empty and clean the tank, filter, and accessories. Remove the battery packs.

MAINTENANCE

WARNING To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the tool, battery pack or charger. Contact a MILWAUKEE® service facility for ALL repairs. Never use vacuum without tank and filter properly installed. Maintaining the filter
Keep filter clean. Clean the filter by twisting the filter cover counter- clockwise to unlock from the motor housing/float cage. Pull the filter away from the vacuum. Empty debris by holding away from the user’s face and tap clean. Water may be used to clean the filter. If cleaning with water, let filter dry 24 hours before using with vacuum. Replace filter if damaged or suction decreases (Single pack, Cat. No. 49901977, 49901978).
Maintaining Tool
Keep your tool, battery pack and charger in good repair by adopting a regular maintenance program. Inspect your tool for issues such as undue noise, misalignment or binding of moving parts, breakage of parts, or any other condition that may affect the tool operation. Return the tool, batterypack, and charger to a MILWAUKEE® service facility for repair. After six months to one year, depending on use, return the tool, battery pack and charger to a MILWAUKEE service facility for inspection. If the tool does not start or operate at full power with a fully charged battery pack, clean the contacts on the battery pack. If the tool still does not work properly, return the tool, charger and battery pack, to a MILWAUKEE service facility for repairs.
Cleaning
Clean dust and debris from any vents. Keep tool clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean, since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include petrol, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger to the nearest authorised service centre.

ACCESSORIES

WARNING
Use only recommended accessories. Others may be hazardous.
For a complete listing of accessories, go online to milwaukeetool.com.au / milwaukeetool.co.nz or  contact a distributor.
Compatible with M18 FVC34L and M18 FVC45L Wet/Dry Vacuum
49902000……………. Dust Extraction Adapter

WARRANTY – AUSTRALIA and NEW ZEALAND

Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to product sold by authorised dealers in Australia and New Zealand.
SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE® prides itself in producing a premium quality product that is Nothing But Heavy DutyTM. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, please contact your authorised MILWAUKEE® dealer. For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE® Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928)or visit milwaukeetool.com.au/milwaukeetool.co.nz.

Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
26 – 40 Nina Link, Dandenong South,
Victoria, 3175, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN USA
PRINTED IN USA

References

• Milwaukee Tool | Official New Zealand Site of Milwaukee Tool | Nothing but HEAVY DUTY®
• Milwaukee Tool | Official Australia Site of Milwaukee Tool | Nothing but HEAVY DUTY®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>