H Koenig V24 L33cm Steam Ironing System Instruction Manual

**H Koenig V24 L33cm Steam Ironing System Instruction Manual

**

Description

1. Heating plate
2. “Iron heating” indicator light
3. Steam request button
4. Thermostat knob
5. Single hase (supply cable + steam hase)
6. On/off indicator light for switch
7. Switch button
8. Steam indicator light
9. Supply cable with plug
10. Storage box for supply cable
11. The cleaning valve of the boiler
12. Storage slot for single hase
13. Boiler
14. Water tank

Safety warnings

Read the following instructions carefully:

• Before use, check that the power supply corresponds to the voltage shown on the serial number plate. Connect the appliance only to a properly earthed power outlet (minimum 1OA).
• ln the event of incompatibility between the plug and you socket, have the socket replaced by a qualified electrician.
• The electrical safety of this appliance is only guaranteed when il is properly earthed according to current electrical safety regulations. The manufacturer declines all responsibility for any damage resulting from inadequate earthing of the appliance. If in doubt, consul! a qualified electrician.
• Do not leave water in the machine when the room temperature is 0°Cor below. After unpacking , check the appliance for damage if in doubt, do not use the appliance; contact a qualified technician.
• Packaging materials (plastic bags, polystyrene foam, etc.) are a potential source of danger and must be kept out of reach of children.
• Il is inadvisable to use adapters, multiple sockets and/or extensions. ln cases in which this is unavoidable, always use adapters, multiple sockets and extensions which comply with current safety regulations. Do not exceed the maximum power rating shown on the adapter.
• This appliance is designed for domestic use only. Any other use of the appliance is considered improper and therefore dangerous.
• The manufacturer declines all responsibility for any damage resulting from improper, incorrect or careless use of the appliance .
• The filling aperture must not be opened during use.
• Don’t allow children in the front of the iron when press “Jet button”,its ‘s shot range is far. Fasten lace is for lashing the steam tube and power cable .
• Il is easy for you to put the long steam tube and cable on the tube clip, il is easy for operating.
• This device is not intended for use by persons with reduced capacity on the physical, mental or sensory or lack of experience and knowledge (including children), unless he has them was asked to monitor or if they have had instructions on the use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the device.
• If the power cord is damaged, il must be replaced with an after-sales service to avoid any danger.

ln particular:

• Do not touch the appliance with wet or damp hands or feet. Do not use the appliance in bathrooms.
• Do not pull the supply cable or the appliance to remove the plug form the socket. Do not leave the appliance exposed to atmospheric agents (rain, sun, frost, etc.).
• Do not allow the appliance to be used by children or irresponsible persons unless under supervision. Do not immerse the appliance in water.
• Do not leave the iron unattended when il is switched on, as this may be a source of danger.
• Before carrying out any cleaning or maintenance operations or filling water into container, always disconnect the appliance from the mains power supply by removing the plug .
• ln the event of failure or malfunction, switch off the appliance and do not attempt to carry out repairs. Contact an authorized Service Centre and insist on original spare parts. Failure to observe the above points may affect the safety of the appliance.
• Should you decide not to use the appliance again, remove the plug from the socket and eut the supply cable to render the appliance completely inaperative.
• Installation must be carried out according to the manufacture’s instructions.
• The supply cable must not be replaced by the user, as this requires the use of special tools, if the supply cable is damaged, contact an authorized Service Centre.
• Do not fill the appliance under a running tap.
• Do not allow the supply cable to corne into contact with the ironing plate.
• If the safety eut-out intervenes, the iron will no longer function. To restore normal operation. Contac a qualified electrician.
• Never direct the steam jet in the direction of persans, as this may be extremely dangerous. Do not use the iron on very wet fabrics.
• Do not place the iron on the stand when the plate is hot.
• Do not overfill the boiler and do not add stain-removers of simllar products to water.
• Remove the plug from the mains socket when the appliance is not in use. Do not leave the appliance switched on unnecessarily.
• Never unscrew the safety valve when the appliance is connected to the power supply network. Use a funnel to fill the boiler without causing the water to overflow.
• The boiler must be placed on a fiat surface that is particularly resistant to high temperatures.
• This appliance may be used by children of at least 8 years of age, as long as they are supervised and have been given instructions about using the appliance safely and are fully aware of the dangers involved.
• Cleaning and maintenance should not be carried out by children unless they are at least 8 years of age and are supervised by an adult.
• Keep the appliance and its power cord out of reach of children under 8 years of age.
• When using electrical equipment, safety precautions must always be taken to prevent the risk of fire, electric shock and/or injury in the event of misuse.
• Make sure that the voltage rating on the typeplate corresponds to your main voltage of your installation. If this is not the case, contact the dealer and do not connect the unit.
• Please keep this document at hand and give it to the future owner in case of transfer of your device.
• The device must not be used if it has been dropped, it obvious signs of damage are visible or if it has leaks.

INSTRUCTIONS FOR USE

Check the manufacturer’s label on the garment and interpret the symbol on label as follows:

Steam ironing allowed
For dry ironing, set temperature adjustment knob (4) on …

Steam ironing allowed
For dry ironing, set temperature adjustment knob (4) on …
Dry ironing
Check the fabric’s resistance to steam ironing or dry iron with temperature adjustment knob (4) set on..
Do not iron
Steam ironing or treatment not allowed

STEAM IRONING

The appliance uses ordinary tap water.
If the water is very hard (hardness higher than27 degrees French).we suggest using distilled or demineralized water.
When using the iron for the first lime, iron a plain cloth first.
Before using the appliance, taken down the water tank (14) and fill it, not exceeding MAX waterline.
When you want to take back the water tank(14),firstly put the water tank base and then push the water tank softly, after hear “click”, it means the water tank in the place.
Connecting the appliance and power cord.
Press the switch button (7), power indicator light (6) and steam available indicator light (8) bright, il means the boiler and iron start running.
Feed-water from electromagnetism water pump coming down the boiler when the boiler (13) heating enough.
Choosing the temperature by temperature knob (4), the steam device indicate ironing area which can be chose (Fig.3).
Around 2 minutes, heating indicator (2) will die out, il means the appliance can be using the steam.
Around 3 minutes, steam available light (8) will die out, it means the appliance can be using the steam.
Obtain steam after pressing the steam button (3). Release the button (3) and the steam flow stops.
This appliance is also able to generate steam in a vertical position and can therefore be used to refresh fabrics easily with a jet of steam.
When you ending the ironing, press the switch button (7), cut down the power, press the steam button (3) to release the residual steam in the boiler (13)

NOTE: Continue to release steam for long time, when pump adds water into boiler, soleplate will stop to release steam for short time, almost 10secs.

DRYIRONING

Connect the appliance to the mains supply, press the switch button(7), then select the desired temperature by turning the thermostat knob(4).Wait until the iron heating indicator light (2) goes off, indicating that the desired temperature has been reached. For dry ironing it is not necessary to press the steam button (3).

FILLING THE TANK

Thanks to the self-filling function, there is no longer any need to stop and wait while the boiler fills up again.
When the water in the boiler is at minimum level, the pump is automatically activated which fills the boiler once again.
If you hear the loud feed-water sound when you ironing, it means there is no water in the water tank (14).Press the switch button (7) and cut down the power. After fill the water tank (14), then press the switch button (7) again, go on ironing.
To keep on working, simply restore the water level in the self– refilling tank as described in the “Preparation for use” paragraph.

PUTTNG THE APPLIANCE AWAY

First ensure that the appliance has cooled down completely. Empty the water tank (14) .
lt is not necessary to drain the boiler after ironing.
Steam line (5) and power cord (9) could be receipt into the wire groove (12) and line box (10).

LOCKING IRON

To Iock the iron it must be set on the rear part of the rest mat (Fig11). NOTE: make sure to firmly hook the iron to prevent it falling accidentally.

CARE OF YOUR STEAM IRONING

Before attempting any maintenance operation, always disconnect the appliance from the mains. To clean the body of the appliance, simply use a moist cloth. Do not use solvents or detergents which may harm the body material.
Always keep the surface the ironing plate perfectly clean. To clean it, jus! wipe the cold surface with a damp cloth. The appliance must not be cleaned with descaling agents.
Do not iron over zippers, hooks, rings, etc; as these may scratch the plate.
When you have finished ironing. Place the iron correctly on its stand. Ensure that there are no traces of water under the plate, as these may cause stains.
Store the appliance in a dry place

PERIODIC CLEANING OF THE BOILER

• To maintain optimum performance, clean the boiler every 10/20 uses depending on the amount of limestone in the water.
• Disconnect the appliance and let it cool down for at least 2 hours.
• After the appliance refrigeration enough put up one side of the cleaning valve (11), forced to rotate counterclockwise the cleaning valve (Fig.5) (do not lie fiat the appliance when you open the cleaning valve, otherwise the water will leakage).

CAUTION! Never attempt to open the cleaning valve ( 11) while the boiler is under pressure.

CAUTION: do not pour more than 200ml water into the boiler. Pour water
slowly, being careful not to let it overflow, as this could damage the appliance.

• Rinse out the boiler and pour the water away into the sink or into a container for collecting dirty water.
• If the water is very dirty, repeat the operation until it is clean.
• Checking that the seal is present and that the cap is screwed on properly.
• Fill the water tank again.
• Turn the appliance on again.
• Before ironing, release steam into the sink or another container and check that the steam is clean. This should take a few seconds.
• Resume ironing normally.

TROUBLESHOOTING

the right temperature yet.
The temperature control dial has set at the minimum.| Wail for the “Steam Ready” indicator light and the iron indicator light to turn off. lncrease the regulation of the temperature control dial.
The appliance is on but it is not producing steam| Water tank is empty or not inserted correctly.| Fill the water tank.

Suggestions

Divide the washing according to the correct ironing temperatures. Start by ironing those garments that require a lower temperature. For fuller details, refer to the chart at end of this booklet.

Fabrics such as velvet and wool, and accessories such as gloves, handbags, etc. will regain their brand-new look and texture by simply passing the iron near the surface of the fabric and pressing the steam button.
lmprints left in carpets by furniture can be removed by applying steam on the parts where the pile is crushed and the brushing lightly.
_I f the carpet is made of synthetic material, do not select a high temperature.

How to get a professional ironing finish

A normal iron generates only a small quantity of steam. ln this case it is necessary to products steam constantly in order to eliminate crease in the fabric being ironed.
A professional ironing system works rather differently. The fabric is first made damp by the steam and then, in a second phase, dry-ironed in the normal way. This means that every. Tiniest crease is removed and your garments are ironed to perfection.
ln the first phase (steam-damping of the fabric),hold the ira about 20 cm above the fabric and press the steam(3). Pass the iron over the garment in a circular movement so that the powerful jet of steam damps the fabric. Lightly creased garments require only a few moments of steaming. While very heavy fabrics or garments with particularly difficult creases must be damper, so steam must be applied for a few seconds more.
During the second phase (dry ironing), check that the thermostat knob is in the correct position for the type of fabrics; release the steam button(3) and dry-iron the garment. The special ironing plate will prevent the fabrics from becoming shiny. Using this ironing technique, and following the suggestions in the chart below, you will find it easy to give your garments a really professional ironing finish.

Guide to perfect ironing

Check the manufacturer’s label on the garment, and interpret the symbol on the label as follows.
Type of fabric| Position of thermostat knnh| Ironing instructions
Acetate Acrylic Nylon| •| Dry ironing
Follow the instructions on the label of the garment. This type of fabric generally requires very light ironing.
Pollester Rayon| •| Dry ironing
Iron inside out. When ironing mixed fabrics.
Lowest recommended temperature.
Silk| •
•| Dry ironing Iron inside out
Woo
Light cottonLight linen| •
•| Steam ironing
Iron inside out Place a thin cloth over the fabric in order to avoid a shiny finish
Cotton
Fine linenStarchedfabrics| •
•
•| Steam ironing
Dampen the fabric before ironing. Heavier fabrics and tarched fabrics can be ironed on the front; darker colours and embroidered garments should be ironed inside out.
Linen| •
•
•| Steam ironing
Use plenty of steam and iron dark fabrics inside out in order to avoid a shiny finish. Iron lapels and cuffs on the right side for better finish.

ENVIRONMENT

CAUTION : Do not dispose of this product as it has with other household products. There is a separation of this waste product into communities, you will need to inform your local authorities about the places where you can return this product. In fact, electrical and electronic products contain hazardous substances that have harmful effects on the environment or human health and should be recycled. The symbol here indicates that electrical and electronic equipment should be chosen carefully, a wheeled waste container is marked with a cross.

Adeva SAS / H.Koenig Europe – 8 rue Marc Seguin, 77290
Mitry-Mory, France www.hkoenig.com – sav@hkoenig.com –
contact@hkoenig.com – Tél: +33 1 64 67 00 05

References

• H.Koenig : Le spécialiste du petit électroménager

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>