Solowii M2 Electric Scooter User Manual
- June 6, 2024
- Solowii
Table of Contents
- Welcome
- Safety Precautions
- About the Product
- Product Display
- Assembly Guide
- Unfolding/Folding/Carrying
- Riding and Parking
- Control System
- Indication Description
- About Charging
- About the Battery and Charger
- Instructions for APP
- Care & Maintenance
- Troubleshooting
- Product Specifications
- Authentication
- Instruction Manual Annex 1
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Solowii
M2 Electric Scooter User Manual
Welcome
Thank you for choosing the 5TH WHEEL electric scooter 5LCHM02 (hereinafter
referred to as M2).
Enjoy the pleasure brought by M2.
Safety Precautions
Please read the following instructions carefully before use.
-
M2 is designed for and can only be used by adults.
Besides, do not ride it with anyone else, including children -
Please wear a safety helmet and other protective equipment when riding M2.
-
Please ride M2 in accordance with the local laws. And do not ride it in unsafe or illegal places.
-
Please practice riding M2 in the open space for the first use and avoid riding it on the traffic line. After knowing its operation completely, you can ride it on the road in accordance with the local laws.
-
Do not engage in any dangerous actions or ride M2 without both hands gripping the handles. And keep your feet on the scooter.
-
Do not try to cross bumps higher than 3cm (0.39inch) directly, which may overturn M2 and cause injury to the user or damage to the scooter. And avoid riding through potholes lower than 3cm (0.39inch) as far as possible.
-
For your riding safety, please control the speed within 15.5mph. Please try to avoid riding at night. If you are riding at night, please turn on the lights and control the speed at 9.3mph or below.
-
Do not ride it in an environment below 23℉.
-
When riding on the uneven road surface or poor road condition, please slow down and ride carefully or get off the scooter to pass through.
-
Do not ride it on slippery roads (such as roads covered with ice, oil, etc.).
-
Do not immerse M2 in puddles deeper than 4cm (1.57 inches) to avoid damages to the electrical part due to water inflow.
-
In rainy, snowy, windy, and other bad weather, please do not ride it to avoid damages caused by unnecessary factors.
-
The user should ride it in accordance with the relevant instructions described in the user manual.
Anything placed on the product should not be heavier than the max weight capacity of M2. -
Please avoid riding it or placing it in an environment with too high or too low a temperature. Please do not place M2 near combustibles, so as to avoid fires under accidental circumstances.
-
M2 is a special riding product. Please ride it on a flat road without potholes.
-
Do not have any load attached to the handlebar which will affect the stability of the vehicle.
-
Engage the kickstand when the vehicle is not in use Flip up the kickstand before use; Do not park the vehicle on the slope.
-
The minimum height of the user is 1.4m, while the maximun height is no more than 2.2m; the maximun age of the user is 70 years old, while the minimum age is no less than 13 years old.
-
Braking performance and friction between the tire and road deteriorate in wet conditions, so it is harder to control the speed and easier to lose control. Slow down and break early when it is raining.
-
.WARNING Keep plastic covering away from children to avoid suffocation.
-
The user shall take the time to learn the basics of the practice to avoid any serious accident that can take place in the first month.
-
Notify your presence when approaching a pedestrian or cyclist when you are not seen or heard. Avoid high traffic areas or overcrowded areas.
-
Cross the protected passages while walking. In all cases, take care of yourself and others.
-
Do not divert the use of the vehicle this vehicle is not intended for acrobatic use.
-
Caution, the brake may become hot in use. Do not touch after use.
-
Eliminate any sharp edges caused by use. Do not modify or transform the vehicle, including the steering tube and sleeve, stem, folding mechanism, and rear brake.
-
The user has the obligation to always wear shoes when riding.
-
In any case, anticipate your trajectory and your speed while respecting the code of the road, the code of the sidewalk, and the most vulnerable. If any, local
special laws and regulations should be observed during the riding of this product.
About the Product
Product Overview
Accessories
Please carefully check whether the items in the packing box are complete and intact.
Product Contents | Quantity |
---|---|
User Manual | 1 |
Screws | 4 |
Fastening Tool | 1 |
Tool Kit | 1 |
Power Adapter | 1 |
Product Display
Upright State
Folded State
Assembly Guide
-
Unfold the scooter and put the kickstand down.
-
Pull the spring to bring out the lower mainline connector.
-
Connect the mainline and attach the handlebar to the stem.
-
Tighten the screws with the tools included in the package and press the power button to check if it works normally.
Unfolding/Folding/Carrying
- Push up the shackle.
- Pull the folding handle downwards and outwards.
- Lift the head of the scooter.
- Close the folding handle upwards.
Folding Operations
Note: For your safety, it is recommended to perform the folding operation
after the scooter is powered off.
- Push up the shackle.
- Pull the folding handle downwards and outwards.
- Lower the heat of the scooter to be horizontal.
- Close the folding handle upwards.
About Carrying
Note: After folding it, carry the scooter with one or both hands.
Riding and Parking
Preparations before Riding the Scooter
- Choose a suitable place for riding the scooter.
- Unfold the scooter by following the instructions described in the user manual and wearing protective equipment.
Starting Riding the Scooter
- Press the Power switch to turn on the scooter.
- Stand on the pedal with one foot on the ground.
- Slide the scooter forward and press the throttle gently downward. And the scooter will move forward slowly. When riding it smoothly, stand on the pedal
with both feet. The greater you press the throttle downward, the faster the speed.
Note: For safety, M2 is designed with a non-zero start. The throttle will take effect only after the scooter slides forward for a certain distance.
Parking
- Under normal circumstances, by pressing the left brake, the scooter will stop moving immediately. The greater you press the left brake downward, the greater the braking force.
- In an emergency, you can step on the rear brake with your foot to reach the front wheel electronic brake and the rear wheel friction brake at the same time.
Control System
A Power Switch
B Gear Indicator
C Throttle
D Brake Control
E LED Display
F Bell
LED Display
Power Switch
Short press the Power switch for 1 second to turn on the scooter, and long-
press the Power switch for 3 seconds to turn it off.
Gear Setting
Press the power button twice quickly to switch the gear. The gear can be set
to Level 1 (max. 6 km/h,The pedestrian mode), Level 2 (max. 16 km/h), and
Level 3 (max. 25 km/h).
Speed control
When riding the scooter at a speed faster than 3km/h (1.86 mph), the throttle
will get started and take effect. By pressing the throttle, the user can
control the riding speed. (Speed Range: 1-25km/h / 0.62-15.53 mph)
Brake control
Hold the left brake lever to brake. The greater the holding force, the greater
the braking force. The indicator will blink under the condition of braking.
LED Headlight Switch
After switching on the scooter, click the LED headlight switch to turn it on.
Emergency Braking
When encountering an emergency, step on the rear brake with your foot. At this
time, the rear wheel friction brake and the front wheel electromagnetic brake
can work at the same time. Under normal circumstances, do not use emergency
braking vigorously during high-speed driving, so as to avoid the riding risk
or damage to the rear wheel. The company is not responsible for the damage.
Tyre pressure
Before riding, please make sure the tire pressure is no less than 2.8KPA.
Otherwise, the mileage will decrease each time. The tire pressure may also be
under the standard value if the scooter is unused for a long time.
(This is applicable for the scooters equipped with pneumatic tires.)
Cruise control
The scooter is not initially configured with the cruise control speed. If
necessary, open the mini-program and select the cruise control speed. When the
scooter is running at the constant cruise control speed, the cruise control
will be enabled. After the cruise control is enabled, you can release the
thumb accelerator, and the scooter will automatically run forwards at a
constant speed. Hold the left brake lever to disable the cruise control. When
the speed of the scooter reaches the set cruise control speed, the cruise
control will be enabled again.
You can set the status of no cruise in the mini-program to disable the cruise
control function.
Noise emission
The A-weighted emission sound pressure level of the vehicle in operation is
less than 70 dB(A).
Indication Description
LED Power Indication
Each LED indicator represents 20% of the power. When the battery power is
below 10%, M5 flashes.
80% >60% >40% >20% <10% M1-M5 light up M3-MS light up M4-M5 light up M5 light up M5 flashes
Cruise Control Indication
Turn On | Turn Off |
---|
When the cruise control is turned on, the indicator light
will stay on.| When the cruise control is turned off, the indicator light
goes out.
T3 lights up| T3 goes out
Headlight Indication
Turn On | Turn Off |
---|
When the headlight is turned on, the indicator light will
stay on.| When the headlight is turned off, the indicator light goes
out.
T1 lights up| T1 goes out
Gear Indication
Gear 1 | Gear 2 | Gear 3 |
---|---|---|
Gear 1 is enabled. | Gear 2 is enabled. | Gear 3 is enabled. |
T6 lights up, T7 & T8 go out | T7 lights up, T6 & T8 go out | T8 lights up, T6 & |
T7 go out
Error Indication
If there is anything abnormal about the scooter, the warning indicator will
flash, with the flashing value E1-E6 displayed.
Errors | Code | Solutions |
---|---|---|
Communication Fault | El | Please check whether the taillight is on. If it is |
off, it means that the power supply is insufficient. Please replace the
controller or the LED display. If it is on, please check whether the
connecting wire between the controller and the LED display is open-circuit.
Brake failure| E2| Please check whether the brake is pressed.| Press and
release the brake to reset the brake.
f not, please check whether the
connecting wire between the
brake and the LED display is
short-circuited or open-circuit.| If it is open-circuit or short-circuited,
please replace the connecting wire.
Replace the brake handle.
Throttle Failure| E3| Please check whether the throttle is pressed.| Press and
release the throttle to reset the throttle.
If not, please check whether the connecting wire between the throttle and the
LED display is short-circuited or open-circuit.| If it is open-circuit or
short-circuited, replace the connecting wire.
| Replace the throttle.
Motor Fault| E4| Check whether the motor and controller wire is connected
correctly.| If it is not connected correctly, please adjust and connect the
motor and the controller correctly.
If it is connected correctly, please disconnect the connecting wire and
measure whether the internal resistance between the three-phase wires of the
motor is within a reasonable range, generally within 0.10-10. If it exceeds
the range, the motor needs to be replaced.
Controller failure| E5| If the controller is damaged, please replace the
controller.
Overheated Motor| E6| Check whether the motor temperature is too high.| If the
motor temperature is too high, please wait for the motor to cool to the
appropriate working temperature.
If the motor temperature is normal, check whether the connecting wire of the
controller is short-circuited. If it is short-circuited, please replace the
connecting wire.
Over-speed alert| Flashing| Reduce the riding speed.
About Charging
- Open the rubber plug.
- Plug in the charger.
- Insert the rubber plug and fix it after charging.
Step 1. Open the rubber plug and insert the charger into the charging port on
the scooter.
Step 2. Insert another end of the charger into the power outlet.
Step 3. When charging, the red indicator on the charger will light up.
When the indicator turns green, it means that the scooter is now fully
charged.
About the Battery and Charger
M2 electric scooter is equipped with a special lithium battery and a special smart charger. The scooter and its accessories have a special number. Do not use chargers of other brands, nor should other types of products be charged with the charger of our company. The company will not be responsible for the accessories damaged by misuse.
Battery
The lithium battery provided by the company can be recharged for at least
800times, and more than 1,000 times under normal circumstances. Please charge
the full battery for the first time before using it. The battery can be charged
at any time, and there is no damage to charging it frequently. Meanwhile,
please don’t forget to charge it per 3 months if you don’t use it for a long
term.
Charger
The dedicated charger provided by the company has the function of charging
protection. When the battery is 100% charged, the charger will be powered off
automatically. The charging time is about 4-5 hours. Damage to the battery
arising from water, collision, and other abnormal factors is excluded from the
warranty policy.
Charging instructions
- Open the rubber and insert the plug into the hole;
- Insert another plug of the charger into the electric outlet;
- When the indicator lamp is red, it shows the battery being charged; When the lamp turns green, the battery is finished charging.
- Please shut down and keep away from water before charging.
- Only use the specified charger for charging.
- Warning: Please be careful not to get an electric shock.
Kinetic energy recovery
Press the brake in the running process to enable the kinetic energy recovery
system and convert part of kinetic energy into electrical energy to be stored
and used. The kinetic energy recovery system can enhance the experience of
emergency braking. At the same time, the recovered kinetic energy can help
increase endurance. Changes in the power are displayed simultaneously.
Instructions for APP
-
Downloading the Apphttp://appen.invanti.com/index.html
Scan the QR code to download the App. -
Please turn on the scooter before the connection.
-
Finish the connection by following the instructions.
-
Register your account using your email. A PIN code is sent and needed in this procedure. Scan the bar code under the scooter and bind the vehicle.
Special note: about the locking function, It can only ensure that the vehicle
cannot run normally Due to the lightweight of the whole vehicle and
The whole vehicle is composed of mechanical parts
It can be removed with corresponding tools
To ensure that the vehicle is not stolen,
Please park your vehicle insight
Enclosed or added machinery and Fixtures
*The actual content shall be subject to the app display interface
Care & Maintenance
Lubrication
For maintenance, add a small amount of white grease or lubricant to the folded
part once every six months.
Check the scooter once every three months for screw loosening. Tighten the
loose screw.
Battery
When you get the electric scooter for the first time, please fully charge the
battery before using the scooter.
The battery can be charged at any time to ensure the power supply. It will not
be damaged during charging.
When not in use, the battery needs to be charged once every three months.
*Laboratory data
Storage and daily maintenance
Avoid leaving scooters under direct sunlight or in severely humid places for a
long time.
Keep the scooter clean.
Regularly check the tightening of the various bolted elements, in particular
the wheel axles, the folding system, the steering system and the brake shaft.
Cleaning Recommendations
If you see stains on the scooter’s body, wipe them off with a damp cloth. If
the stains won’t scrub off, put on some toothpaste, and brush them with a
toothbrush, then wipe them off with a damp cloth.
Do not clean the scooter with alcohol, gasoline, kerosene, or other corrosive
and volatile chemical solvents to prevent dire damage. Do not wash the scooter
with a high-pressure water spray. During cleaning, make sure that the
scooter’s turned off, the charging cable is unplugged, and the rubber flap is
closed as water leakage may result in electric shock or other major problems.
Routine Inspection
- Before riding, please confirm the folding mechanism is locked;
- Please check whether the tires are badly worn. Please contact the local authorized dealer if they need to be replaced;
- Please check whether the wear condition of the brake pad affects the use of the brake system. If so, please contact the local authorized dealer to deal with the problem;
- The screws used in this product are self-tightened screws. Please note that the effect may be gone after several times of tightening.
Troubleshooting
If there is any problem with the scooter, please try to solve it in the following ways.
-
The display screen is black.
Cause: The exposure time in the sun is too long.
Solution: Please place the scooter in a dark environment for a period of time and it will return to normal. -
The value is inconsistent with the actual value.
Cause: The parameter setting is incorrect or missing.
Solution: Long press the Power switch to shut down the scooter, and then short press the Power switch to restart it. -
The displayed value is dim.
Cause: The battery connection is loose, or there is no battery power left.
Solution: Turn off the scooter and restart it. If the problem remains, please contact the customer service via https://5thwheel.afterservice.vip -
The product cannot work normally.
a. Please make sure that it is powered on.
b. Check whether there is battery power left by viewing the display screen.
c. Check whether the left brake and rear brake are in place.
d. Check whether all ports and power cables are connected accurately.
If all the above steps are checked and the product still cannot work normally, please contact us via https://5thwheel.afterservice.vip -
The screw at the junction of the handlebar and the stem is loose.
Cause: The loose screw is a spare locking screw, which is loose by default in the factory setting, without affecting normal use.
Solution: The user can adjust and lock by the screw if necessary.
The mechanical vibrations transmitted by the Electric Scooter are less than 2.5 m/s2. The uncertainty of measurement is. -
Braking Distance 2.5m
The braking distance of this product is measured under the conditions of 75kg loading, 24℃ temperature, 55%-65% humidity, 2.9 bar tire pressure and asphalt pavement.
Handlebar commissioning
After repeated use of the electric scooter, screws may become loose, which may
cause the vertical rod to shake. If the vertical rod is shaking when riding,
use the hexagon wrench to tighten the hexagon screw under the left side of the
handlebar clockwise as shown in the figure.
(Note: The hexagon wrench is provided in the commissioning tool kit.)
Torque:6-10N·m
Disc brake commissioning
If the brake is too loose, use the hexagon wrench to tighten it clockwise. If
the brake is too tight or the brake disc is abnormal, use the hexagon wrench
to loosen it counterclockwise. (The aforesaid screw is on the right side of
the rear tire, which needs to be tightened or loosened from the left side of
the rear tire through the hub.)
(Note: The hexagon wrench is provided in the commissioning tool kit.)
Torque:6-10N·m
If the braking problem is still not resolved after in strict accordance with
the commissioning method as shown in the left figure, please use the hexagon
wrench to loosen the screws on the tension disc as shown in the figure above,
and adjust the brake by controlling the length of the exposed end of the brake
cable.
Torque:6-10N·m
Product Specifications
Parameter | Product name | 5th Wheel Scooter M2 |
---|---|---|
Model | 5LCHMO2 | |
Dimension | Upright: LxWx H | Approx. 43 x 43 x 20 inches |
Folded: LxW x H | Approx. 43 x 16 x 28 inches | |
Weight | Net weight | Approx 331bs |
Status | Max Load | 2201bs |
Main parameters | Max Speed | About 15.5mph |
Travel Distance | 16-19miles (Depends on factors such as environment, angle, |
speed, driving habits, etc.)
Max Incline| Approx. 14°
Applicable Terrain| Stable and smooth road surface, with bumps less than 2cm
and depressions less than 3cm
Tires| 8.5-Inch Honeycomb Tire(Tire pressure range: 2.1-2.8Kpa)
Damping System| Spring Damping + Concealed Damping + Tire Damping
Dustproof and Waterproof Grade| IP54
Braking System| Motor brake + Disc brake + Foot brake
LED display| Speed, Mileage, Gear
Lighting system| LED high-brightness headlight
Motor power| 350W
Parameters about Charging| Charger Rated Input Voltage| 100V-240VAC 50/60Hz
Lithium battery| 36V-7.5AH
Charging time| 4-5h
Authentication
Applicable model: M2
The product has passed the ANSI/CAN /UL-2272 certification of the CSA.
The battery complies with the UN/DOT 38.3.
According to the Federal Communications Commission (FCC) Compliance Statement
as follows:
The product complies with part 15 of the FCC rules, and the operation must
meet the following two conditions: (1) the product should not cause harmful
interference, and (2) the product must accept any received interference,
including interference that may lead to accidental operation. Any change or
modification not expressly approved by the responsible party may make void the
user’s right to operate the product.
The EU Compliance Statement is as follows:
WEEE needs to properly dispose of and recycle the product. This sign indicates
that the product should not be disposed of together with other domestic waste
throughout the EU.
Therefore, in order to prevent possible harm of uncontrolled waste treatment
to the natural environment or human health, it is necessary to recycle it and
promote the sustainable reuse of material resources. To recycle the used
product, use the return and collection system or contact the retailer who can
use the product for environmentally safe recycling.
EU Battery Recycling Information:
Batteries or battery compartments are marked in accordance with the European
Directive 2006/66/EC and the amendment 2013/56/EU on batteries and accumulator
cells and scrap batteries and accumulator cells.
The directive applies to the recycling framework of waste batteries and
accumulator cells throughout the EU. The label on the battery indicates that
the battery should not be discarded, but recycled at the end of its service
life according to the directive.
According to the European Directive 2006/66/EC and the amendment 2013/56/EU,
batteries and accumulator cells are labeled to indicate that they will be
collected separately and recycled at the end of their service life. The label
on the battery may also contain the chemical symbols of the relevant metals in
the battery (Pb, Hg and Cd). Users should not dispose of batteries and
accumulator cells as garbage, but use the collection framework available to
customers to recycle and dispose of batteries and accumulator cells. With the
engagement of users, it is important to minimize any potential impact of
batteries and accumulator cells on the environment and human health due to the
presence of potentially hazardous substances.
Before placing electrical and electronic equipment (EEE) into a waste
collection stream or waste collection facility, users of equipment containing
batteries and/or accumulator cells must remove these batteries and accumulator
cells for separate collection.
Restriction of Hazardous Substances in Electrical and Electronic Equipment
(RoHS) Directive.
The products and parts (cables, wires, etc.) of Ivanti (Beijing) Technology
Co., Ltd comply with the requirements of directive 2011/65/EU on restricting
the use of certain hazardous substances in electrical and electronic equipment
(“RoHS recasting” or “RoHS 2”)
Trademark and Legal Statements
5TH WHEEL is a registered trademark of Ivanti (Beijing) Technology Co., Ltd
(hereinafter referred to as “Ivanti”), which is authorized to be used by
Solowii (Beijing) Technology Development Co., Ltd. Android, and Google Play
are trademarks of Google Inc. and the App Store is the service mark of Apple
Inc. Their respective owners reserve the trademark rights mentioned in this
user manual.
The products involved in the registered trademark of 5TH WHEEL are protected
by relevant patent laws. For relevant patent information, please visit the
website: http://www.invanti.com.
In this user manual, we make our utmost to describe all the instructions and
functions of the M2 electric scooter. With constant updates and iteration, the
M2 electric scooter received may be slightly different from the product
features shown in this manual. For more information, please visit the Apple
App Store (iOS) to download the App.
Please note that Ivanti has developed products with many functions and
different models of products, and some of the functions mentioned here may not
be applicable to the product or equipment received. The manufacturer reserves
the right to change the design and function of the M2 electric scooter and
documents without notice.
2021 Invanti (Beijing) Technology Co., Ltd all rights reserved.
Contact Us
If you encounter any problems when using the product, please feel free to
contact us through the following methods or scan the QR code to get a quick
response and a satisfactory solution.
Amazon Platform: “Contact Seller”
Email Address: 5thwheel@afterservice.vip
Get 24/7 Customer Service
Use Camera or QR Scanner to Scan Or Visit: https://5thwheel.afterservice.vip
Instruction Manual Annex 1
FCC 15.21 Information to user Please note that changes or modifications not
expressly approved by the party responsible for compliance could void the
use•’ s authority to operate the equipment.
FCC 15.105 Information to the user (Class B) Note: This equipment has been
tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TVtechnician for help.
The illustrations and function descriptions in this user manual are for illustration purposes and reference only, and the products are subject to the real product. The mentioned technical performance indicators are based on the specific experimental environment, and the actual indicators may vary depending on the setting and environment. This product needs to be used with mobile phones or other smart devices. The realization of all functions of this product requires network support, with the network fee being subject to the supplier’s service rate. This product is only used to assist safety management and cannot replace other safety measures. Do not use this product for any illegal purpose. Some services are provided and supported by third parties, which may change at any time. Ivanti does not provide any guarantee for third- party services. Please read the terms of the third-party service and privacy policy carefully before use.
The text and logo of 5TH WHEEL are trademarks or registered trademarks of enterprises affiliated with Ivanti. Other company, product, or service names mentioned may be trademarks or registered trademarks of their respective owners.
© 2021 Invanti (Beijing) Technology Co., Ltd all rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>