MODSTER 299433 Brushless Transmitter User Manual

BRUSHLESS
TRANSMITTER
USER MANUAL

Warning

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product.

CAUTION: Procedures, which if not be properly followed, is able to create a possibility of physical property damage AND or the possibility of injury.

Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. lt must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt to disassemble, use incompatible components or augment the product in any way without the approval of MONSTER. This manual contains instructions for safety, operation, and maintenance. lt is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Safety Precautions

• Always ensure all batteries have been properly charged prior to using the model.
• Always check all servos and their connections prior to each run.
• Never operate your model near spectators, parking areas, or any other area that could result in injury to people or damage of property.
• Never operate your model during adverse weather conditions. Poor visibility can cause disorientation and loss of control of your model.
• Never point the transmitter antenna directly toward the model. The radiation pattern from the tip of the antenna is inherently low.
• lf at any time during the operation of your model you observe any erratic or abnormal operation, immediately stop operation of your model until the cause of the problem is ascertained and corrected.

Transmitter Details

ON/OFF Switch

Battery LED Monitor

7:3 / 5:5 Switch Instruction

Adjust the proportion of throttle signal on either side of the center trigger position. You can pick which proportion of forwarding/reverse you prefer. We recommend using the 7:3 position for most applications.

Servo Reversing Switches
If the direction of travel on the rudder is backward, slide the steering reverse switch to the other position.
It is the same principle for the throttle reverse switch.

Steering Rate Knob

Rotating the knob clockwise will give you a greater range in rudder movement. Counterclockwise will reduce the range of rudder movement. Adjust to suit your driving style and preferences.

Throttle Trim
The throttle trim dial is used to adjust the throttle trim when the throttle stick is released (neutralposition). This is typically used to adjust the brakes. Rotating the dial causes the throttle trim (the throttle position at rest) to be changed.

Steering Thrim
The steering trim dial is used to adjust the steering trim when the wheel is centered.
Rotating the dial changes the steering trim (the steering at rest position). Normally, the steering trim is adjusted until the vehicle tracks straight.

Install Your Receiver
Install the Receiver in your vehicle using double-sided Velcro. Velcro will hold the receiver in place and help isolate it from vibrations. Mount the antenna up and away from the vehicle in an antenna tube. The higher up the antenna is, the better signal it will receive.

CAUTION: Do not cut the antenna.

Receiver Connection and Binding
Binding is the process of programming the receiver to recognize the GUID (Globally
Unique Identifier) code of a single specific transmitter. When a receiver is bound to a transmitter, the receiver will only respond to that specific transmitter. If you need to rebind for any reason, please follow these steps:

1. With the transmitter switched OFF.
2. Power on the receiver, then turn on the transmitter within 5 seconds.
3. The receiver LED will flash for 3-8 seconds to bind automatically.
4. After the receiver LED stops flashing, it means the binding is done.

How to Operate Your Vehicle

Pull the trigger towards the driver for the boat to move forward.

Push the trigger away from the driver, which will move the boat in the reverse direction.

The proportional speed control means the farther you pull it the faster the vehicle will go.
Release the trigger to stop.

When you upgrade to brushless speed control with the reverse function, pushing the throttle trigger forward will make the motor run in reverse and back the vehicle up.

Rotate the steering wheel clockwise while holding the trigger to turn right. If the steering is not tight enough, increase the travel volume by treating the travel rate knob clockwise till you reach the desired amount.

Rotate the steering wheel counter-clockwise while holding the trigger to turn left. If the steering is not tight enough, increase the travel volume by rotating the travel rate knob clockwise till you reach the desired amount.

Error Search of your transmitter

– You are around metal objects.
The model selected is not the model bound to.
– The model is not the bound one.| – Take transmitter 1 to 3 meters away from the receiver.
– Try in an area with less metal around.
– Check the selected model and ensure you are bound to the specific one.
– Rebind your transmitter and receiver.
The receiver goes into a failsafe mode not matching the distance from the transmitter.| – Check the receiver antenna to ensure it. Is not cut or damaged.| – Replace the receiver and rebind to the transmitter.
– Make sure your receiver antenna is above the vehicle and is in an antenna tube.
The receiver does not respond during operation.| – Low battery voltage.
– Loose or damaged wires or connectors between battery and receiver.| – Check the wires and connection between the battery and receiver.
– Repair or replace wires and/or connectors.

BRUSHLESS
TRANSMITTER

MSG ONLINE GMBH
WIRTSCHAFTSPARK 9
A-8530 DEUTSCHLANDSBERG

FIRMENBUCH GRAZ FN3152307
• UID-NR. ATU 64361513
EVA-PARTNERNUMMER 152216
ARA LIZENZNUMMER 17749
• GRS NUMMER: 110072576
INTERSEROH HERSTELLER ID (EAR): 152204
WEE REG.-NR. DE 44576630

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>