HOLYHIGH AEA03 Truly Wireless Earbuds User Guide
- June 6, 2024
- HolyHigh
Table of Contents
AEA03 Truly Wireless Earbuds
User Guide
SUPPORT
For FAQs, detailed user manuals, and more information, please visit https://holyhigh.com or contact us via Email – support@holyhigh.com.
WERNING
Wearing: Choose the silicone eartips and wingtips that are most suitable for your ears.
CHARGING
Charging: Please tear off the protective films from earbuds first, and charge the charging case with a USB-C cable.
ON/OFF
On/Off: If the charging case still has battery power, the earbuds will
automatically turn on once you open the charging case and take them out of the
case. If you need to turn off the earbuds, please put them back into the case
correctly.
Note: The earbuds can be turned on manually by pressing and holding the
touch buttons on earbuds for 2 seconds, or turned off manually by pressing and
holding the buttons for 5 seconds in non-playing status.
PAIRING
Pairing: Open the charging case and take out the earbuds, the earbuds will automatically enter Bluetooth pairing mode. Select “HolyHigh AEA03” from the Bluetooth list of your device and click to connect.
CONTROL
Control:
x1: tap once
x2: double-tap
x3: triple-tap
2S: press and hold for 2 seconds
Notes:
- In mono mode, press and hold L to skip to the next song.
- In mono mode, volume adjustment is unavailable.
RESET
Reset :
- If the earbuds cannot pair with other devices, please reset the earbuds. Delete “HolyHigh AEA03” from the Bluetooth list and turn off the Bluetooth of your phone. Keep the earbuds in ON status, triple-tap L/R and the LED indicator on the earbud flashes white light for 3 seconds then goes out. Put the earbuds into the charging case, and the earbuds have been reset successfully.
- If the earbuds cannot pair with each other, please reset the earbuds. Delete “HolyHigh AEA03” from the Bluetooth list and turn off the Bluetooth of your phone. Keep the earbuds in ON status and double-tap both earbuds simultaneously and the LED indicators on earbuds rapidly flash white light. Put the earbuds into the charging case, and the earbuds have been reset successfully.
DESCRIPTIONS OF LED INDICATORS
Descriptions of LED Indicators:
: Red lights flash rapidly
: Flashing red lights
Ο: Red lights always on
•: Breathing white light
•: White light off
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device complies with CAN ICES-3 (B)/NMB-3(B).
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Model: AEA03
FCC ID: 2ATWG-AEA03
Shenzhen Yuangu Technology Co., Ltd.
IC: 26891-AEA05 Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>