SLINEX ML-20СRHD Individual Outdoor Panel User Manual

June 10, 2024
SLINEX

SLINEX ML-20СRHD Individual Outdoor Panel User Manual

Safety instructions

Read and keep that manual.
The device installation process should be carried out by the qulied specialists. Use the device from the –40 ˚C to +50 ˚C, always keep it within that temperature range. Installation surface should be free from vibration and impact inuence. Keep this device far from open sources of heat, such as radiators, heaters, and ovens. The device can be installed near other electronic equipment in case if the temperature of the environment does not exceed previously mentioned range. The device should be protected from the direct inuence of the natural phenomena, such as direct sunlight, rain or snow. Don’t use aggressive or abradant detergent for the device surface cleaning. Use soft wet cloth or tissue to remove strong dirt.

Attention!
As a result of continuous upgrades and functionality improvements, technical characteristics of the device can be changed without any preliminary declaration. This manual can contain some inaccuracy or misprint. The owner reserves the right to make corrections to the information described in the user manual and device package.

Nature protection

DISPOSAL ICON Don’t throw away the device with other industrial or nutritive trash if you see that symbol. Some regions have separation and recycling systems for the electronic equipment. Connect with local authorities to receive information about recycling of electronic equipment for your region.

Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other languages or reproduced in any way including electronic or mechanical. Document recording and copying is strictly denied without owner permission.

Package

ML-20CRHD outdoor panel − 1 pc.
Wall mounting bracket − 1 pc.
Angle bracket − 1 pc.
Rainshield − 1 pc.
Flush mounting box − 1 pc. (optional)
Mounting screws and anchors − 1 pkg.
User manual − 1 pc.

Specification

SENSOR TYPE
1/2.9” CMOS
RESOLUTION
1920×1080 px.
VIDEO OUTPUT
AHD 1080p (2 MP), AHD 720p (1 MP) or CVBS (PAL)
VIEW ANGLE
115˚
NIGHT BACKLIGHT
Infrared, 1.5 meters distance

LOCK RELAY CONTINUOUS CURRENT
1 A
VOLTAGE
+12 V
POWER CONSUMPTION
2.5 W in working mode
INSTALLATION TYPE
Surface or ush (optional) mount
DIMENSIONS
45×130×24 mm
WORKING TEMPERATURE
–40 … +50 ˚C

Description

INSTRUCTION

  1. Microphone
  2. Night infrared backlight
  3. Video camera
  4. ID card reader
  5. Call button
  6. Speaker
  7. Video camera mode button
  8. Communication cable
  9. ID card reader reset buttton
  10. Speaker volume potentiometer

DIMENSION

Wire colors

Red Power (to the monitor)

Black Ground (to the monitor)
Yellow Video (to the monitor)
White Audio (to the monitor)
Blue COM. (Common) relay terminal
Green N.O. (Normaly opened) relay terminal
Brown N.C. (Normaly closed) relay terminal
Purple Open lock button
Orange Door panel power supply, +12V
Grey Ground (for power supply)

Schematic diagram

Schematic diagram

Installation

Installation

Angle mounting:

  1. Take the angle bracket from the kit and situate it 150-160 cm from the oor line;
  2. Mark and drill two halls inside the wall;
  3. Take two nuts from the kit and hammer them into the drilled halls;
  4. Fix angle bracket on the wall by two screws from the kit;
  5. Fix wall mounting bracket on the angle bracket by two screws from the kit;
  6. Connect all communication wires and x the door panel on the wall mounting bracket by the screw from the down side.

Installation

Flat mounting:

  1. Take the wall mounting bracket from the kit and situate it 150-160 cm from the oor line;
  2. Mark and drill four halls inside the wall;
  3. Take four nuts from the kit and hammer them into the drilled halls;
  4. Fix the wall mounting bracket on the wall by the screws from the kit;
  5. Connect all communication wires and x the door panel on the wall mounting bracket by the screw from the down side.

ID card reader settings

Connect +12V power supply through the orange (+) and grey (–) wires of the door panel communication cable.

Memory reset
Press and hold «ID card reader reset button» during 5 seconds (button situated on the back side and signed as 9 on page 5), until repeatable sound will be heard. It means that ID card reader memry was formatted.

  1. Connect +12V power supply through the orange (+) and grey (–) wires of the door panel communication cable. Memory reset
  2. Press and hold «ID card reader reset button» during 5 seconds (button situated on the back side and signed as 9 on page 5), until repeatable sound will be heard. It means that ID card reader memry was formatted.

«Unlock ID cards setup» and «delete card» modes

  1. In standby mode situate management card near the card reader to enter «unlock cards setup» mode. Door panel will emmit double sound and backlight of the call button will becomes blue;
  2. Situate every unlock ID card that need to be added near card reader, one by one. After each card reading, double sound signal can be heard. In case if current ID card has been already added to the card reader memory then three time sound signal can be heard while touching it near the card reader;
  3. When all unlock ID cards have been added then situate management card near the card reader to enter «delete card» mode. Door panel will emmit double sound and backlight of the call button will becomes red;
  4. Situate any unlock ID card that need to be deleted near card reader while «delete card» mode is active. After double short sound current ID card will be deleted from the door panel list;
  5. While «delete card» mode is active, situate management card near the card reader to exit into standby mode.
  6. Wait for 10 seconds without any actions in «unlock cards setup» or «delete card» modes to exit into standby mode automatically.
  7. Maximum unlock ID cards quantity that can be added to the card reader memory is 248 pcs.

Sound and visual indication.
Door unlock successfull – double short «beep» and call button backlight becomes blue twice;
No such unlock card – triple short «beep» and call button backlight becomes red twice;
«Unlock ID cards setup» mode – call button backlight is constantly blue;
«Delete card» mode – call button backlight is constantly red;
Standby mode – call button backlight is constantly white;
Card setup successfull – double «beep»;
Card is already added – four times short «beep».

Video camera settings

Outdoor panel video camera can work in three basic modes: AHD 1080p (2 MP) – default mode, AHD 720p (1 MP) or analog CVBS (PAL). AHD is a high-resolution mode, so it has better image quality than analog CVBS mode. While using high- resolution AHD modes, the monitor must maintain that kind of signal, otherwise there will be no image on the monitor screen. To switch video camera modes remove resin cap on the back cover of the outdoor panel. Then press and hold camera mode button during 5 seconds to switch from the current mode to the next one in a such sequence: AHD-H (1080P) → AHD-M (720P) → PAL → AHD-H (1080P) …
INSTRUCTION

Limited warranty

Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety instructions described in that manual. Warranty period is 12 months from the moment of the product purchasing (warranty period could be extended up to 24 months or more, depending on the local regulations). Warranty period allows user to make guarantee repair in cases when normal functioning of the product was violated by the fault of manufacturer and the user haven’t oend transporting, installation and working conditions. This limited warranty does not cover any damage to the product that results from improper installation, accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly, repair or modication

Warranty void in such cases:

  • the product was damaged by the fault of the customer;
  • the product wasn’t properly installed according reccomendations from the manual;
  • the sticker on the backside of the product was broken;
  • the product was not used for its intended function

This limited warranty covers only repair, replacement, refund or credit for defective products, as provided above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with determining the source of system problems or removing, servicing or installing products. This warranty excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for any losses or damage attributable to third party software, connected equipment or stored data. In the event a product has been discontinued, manufacturer shall either repair the product, oer to replace it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current value. Repaired or replacement products will continue to be covered by this limited warranty for the remainder of the original warranty term.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals