inateck KB02026 Bluetooth Keyboard Instruction Manual

Instruction Manual
KB02026 Bluetooth Keyboard

Product Overview

Power ON/OFF KB02026

Power ON: Toggle the switch to ON. The indicator 1 will flash in red and then go off in 5 seconds, which indicates the keyboard is on.
Power OFF: Toggle the switch to OFF to power off the keyboard.

off when paired successfully

To pair the KB02026 with a Surface Pro

Step 1: Toggle the switch to ON. The indicator 1 will flash in red and then go off in 5 seconds, which indicates the keyboard is power on.
Step 2: Press the  simultaneously for 3 seconds. The indicator 3 will flash blue, which indicates the keyboard is under pairing mode.
Step 3: On the Surface Pro, select All Settings – Devices – Add Bluetooth or Other Device – Bluetooth. The Surface Pro will display “inateck KB02026” as an available device. Step 4: Select “inateck KB02026” on Surface Pro.
Step 5: The Bluetooth indicator goes off, which means the keyboard has been paired with Surface Pro successfully.

Note:

1. After a successful pairing, the Bluetooth keyboard will pair the surface pro automatically next time. However, when interference occurs or the Bluetooth signal on Surface pro is unstable, the automatic pairing might fail. In that case, please do as the following.
   A. Delete all Bluetooth pairing record related to KB02026 on your Surface Pro.
   B. Turn off Bluetooth on your Surface Pro.
   C. Follow steps under “To pair KB02026 with a Surface Pro” to connect.

2. How to Restore Factory Mode for KB02026.
   Press ESC+ simultaneously.

3. Touch on the touchpad cannot wake up the keyboard in sleep mode.To wake it up, press one of the keys please.

How to Adjust the Keyboard Backlight

1. Press  simultaneously to adjust the color of the backlight. There are 7 colors available in total.
2. Press simultaneously to adjust the brightness of the backlight. Three levels of brightness are at choice.

NOTE:

1. When the battery level is lower than 12%, the backlight turns off automatically.
2. The backlight is not available unless the keyboard is paired with a Surface pro.
3. The backlight will go off automatically if the keyboard is left idle for two minutes. You can wake it up by pressing a single key.

How to Use the Function Keys

1. How to Use F1-F12
   You may press the keys to lock the FN key. A repeated operation can unlock the FN key. (The keyboard disables the FN key lock by default. )
   FN Lock enabled:
   Press to enable the Fn lock, When the FN lock is enabled, press can trigger the functionality owned by Fl key, while press the combination of will dim the brightness of the screen.
   This method applies to all F Keys (Fl-F12).
   Disable the FN lock (Default Status):
   Press the combination can disable the FN lock. When the FN key is unlocked, press the key to dim the brightness of the screen. Press the simultaneously to use the functionality owned by Fl key.

2. The combination of Fn and other keys:
   Press the simultaneously to turn ON/OFF the touchpad of the keyboard. The touchpad keyboard is on by default.

| Check the Battery Level
---|---
| Turn on/off Touch Pad
| Enter to Bluetooth Pairing Mode
| Fn Key Locks/Unlocks
| UK keyboard Layout: I
| UK keyboard Layout: \
| UK keyboard Layout:1

To Check Battery Status

Press simultaneously to check the battery level.

Charging

When the battery is low, indicator will flash in red. If all indicators are off, it means the battery is completely drained. Under both situations, the keyboard should be recharged. The required voltage for charging is 5V with current under 250mA. A current control chip is set inside the keyboard for overcurrent protection. You can recharge the keyboard by using an ordinary phone charger or on the USB port of a computer that regularly
outputs voltage at 5V.The keyboard can be fully recharged in approximately 4-5 hours. Indicator keeps red when the keyboard is being recharged. The battery indicator will turn green when the keyboard is fully recharged.
Note: You can use the keyboard while it is being recharged.

Sleeping Mode

The keyboard will enter sleep mode automatically if there is no operation for half an hour. Wake it up by pressing one of the keys. Under the sleep mode, Bluetooth will disconnect, and you can reconnect it by pressing a single key.

Product Specification

Packing list

• KB02026 *1
• Type-C Charging Cable *1
• Instruction Manual *1

Support

For any inquiries or comments concerning our products, please send email to support@inateck.com, and we will respond to you as soon as possible.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction

Contact Information
USA
Tel.: +1 909-698-7018
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: support@inateck.com
Web: www.inateck.com
Addr.: Inateck Technology Inc, 2078 Francis St., Unit 14-02, Ontario,
San Bernardino, CA 91761

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>