BLAUPUNKT VIO-D40 IP Camera User Guide

BLAUPUNKT VIO-D40 IP Camera

Kit Content

note

• This manual is for reference only. Slight difference may be found in the user interface. All the designs and software here are subject to change without prior written notice.
• All trademarks and registered trademarks mentioned are the properties of their respective owners.

Product Description

1.  Dome cover
2. Dome housing
3. Camera Power connector
4. Ethernet Network port
5. Wireless antenna
6. Waterproof ring
7. Reset button
8. Micro SD card slot
9. Indicator light 1
10. Indicator light 2

network
Red light quick flashing| Device malfunction, fail to boot up or SD card malfunction. Please go to chapter 6 “Help”.

NOTE:
This quick start guide explains the installation and registration of the VIO camera. If you want to learn more about the camera or the Cam4Home Plus app please check chapter 6.

Learn in a Camera

Step 1:
Download and install the “Cam4Home Plus” APP to your smartphone from the App Stores.

Step 2:
Connect your smartphone to your Wi-Fi network.

NOTE : If you are using a dual-band router, make sure that your smartphone is connected to a 2.4 GHz WiFi Network and not to a 5GHz Wifi Network. To learn more about this please check your router manual.

Step 3:
Open the “Cam4Home Plus” APP. Create a user account by pressing the “sign up” button located at the bottom left hand side.

Step 4:
To add a new camera tap the “+” button at the top right of the screen and scan the QR code of the camera (refer to chapter 2 product description). Then follow the instructions on the App to complete the camera registration.

NOTE: If you encounter any problem during the registration, check Chapter 5

Cam4Home Plus Management

Camera dashboard:
Tap on your camera under the main “device” menu. This will bring you to the camera dashboard, where you can see the camera live stream video.

Camera settings:
To access the camera settings go to the settings icon camera dashboard and tap the at the top right.

Push notifications
On the device, menu tap the 3 dot icon and select “Alarm Notifications” Tap the “Alarm Notification” button to activate/deactivate the push notifications. Important: Ensure that you have given permission to show pop up notifications on your smartphone permission settings.

Motion detection
To enable / disable motion detection go to: Camera dashboard –> Settings icon –> Arm settings –> Motion detection. Note: Motion detection is enabled by default.

Video Storage
To store video recordings the camera needs to have a Micro-SD card installed (see chapter 5.1) or a Cloud Storage Plan activated.

NOTE : To receive push notifications “Motion detection” must be enabled.

Installation

• Check your WiFi signal strength and make sure that the WiFi signal is strong at the location of your camera. For best performance, the smartphone needs to be connected to a Wi-Fi network.
• Note: We recommend taking a picture of the label at the back of the camera. In case you need to check the serial number, MAC address or QR-Code at a later stage.

Micro SD installation (optional)

Locate the Micro SD-Card compartment of the D40. (refer to chapter 2 point  8 Slide the Micro-SD card slot to the OPEN position as displayed on the Micro-SD card slot. After the Micro-SD card slot is in the open position open it and place the Micro-SD card inside. Close the Micro-SD card slot and move it to the LOCK position as displayed on the Micro-SD card slot.

NOTE: The Micro SD-Card is mandatory for local recording. Please make sure the Micro SD-Card is CLASS10 rated. Supported are Micro SD-Cards from 8GB to 256GB .

Installation without mounting bracket

Step 1: Find the desired installation location for the camera. Position the camera where a power socket is insufficient proximity. Turn the camera ON and use the live view image from the app to position the camera where everything to monitor is well in view.

Step 2:
Use the included hex wrench to open the dome cover by unfastening three inner hex screws. (see below picture).

1.  Antenna
2.  U-shaped side exit
3.  Rotational Bracket
4. LED Ring
5. Ceiling or Wall
6. Plastic Anchor
7.  Dome Pedestal
8. Installation Screw
9.  Dome Cover
10.  Inner Hex Wrench

Take out the mounting map sticker and stick it on the ceiling or the wall.

Step 4:
Use the mounting map sticker, to mark the position of the drilling points. There are three holes for the screws and a big hole for the ethernet network port and the camera power connector.

Step 5:
Drill through the 3 small marked points and install the plastic anchors on the 3 small holes. Then choose one of the option bellow:

•  If the ethernet network port and camera power connector need to exit from the back of the camera through the installation surface, drill a hole according to the size of the bigger hole on the mounting map sticker. (For the big hole ideally use a SDS-max 20mm drill)
•  If the Ethernet Network port and Camera Power connector need to exit from the side of the camera, the cable must go through the U-shape side exit on dome pedestal. NOTE:
  If due to special circumstances, such as a reinforced concrete wall, it’s not possible to drill a hole of 20mm diameter, you have the option to cut off the thick Ethernet Network port – see “Chapter 2. Product Appearance”, and seal it with a proper sealing tape. With this option only a 12mm diameter drill is needed.
  Alert: If you decide to cut off the Ethernet Port, you will lose the possibility to connect the camera by Ethernet cable to a router or NVR. Additionally, you lose your right of return.

Step 6:
Adjust the dome camera according to the mounting map sticker and line up the three screw holes in the dome pedestal to the three plastic anchors holes. Fix the three screws in the three plastic anchors firmly.

Step 7:
Adjust the dome camera lens by moving the camera rotation bracket, and check the position of the camera with the live image of the camera on your mobile device. The camera rotation bracket can be moved manually by 355 degrees left to right and 64 degrees up or down. To prevent that the LEDs on the LED ring get blocked by the metal housing of the dome camera it is important to rotate the LED ring horizontal-ly by 355 degrees and adjust the lens image to the desired position.

Note: When it rotates to 64° vertically, please pay attention to the image rotation direction to avoid the outer cover blocking IR light and influencing IR effect.
Step 8:
Use three Inner hex wrench screws to fix the Dome housing on the pedestal.

Step 9:
Connect the Camera Power connector to the included power supply cable.Then connect the power supply cable to the power line socket. Optional: If you want to install your camera via Ethernet cable, connect your camera to the router using an Ethernet cable.

Installation with the mounting bracket (optional)

The VIO-DMB1 mounting bracket is an optional accessory purchased separately from the camera. If you desire to install the camera with the mounting bracket please refer to the manual inside the mounting bracket box.

Help

FAQ

If you experience any issue or have questions go to the FAQ in the app at:
“Me” menu -> Settings –> FAQ
6.2 Cam4Home Plus Manual
If you want to learn more details of the Cam4Home Plus APP, download the Main APP manual, with the following steps:
Visit: https://www.blaupunkt.com/service

1. On the 1st dropdown menu select your language
2.  On the 2nd dropdown menu select “VIO-Series”
3.  On the 3rd dropdown menu select “Manual”
4. Click “Submit”
5. Locate and click on “VIO– Cam4Home Plus – Manual” How-to Videos

For “How-to-Videos” on the installation and registra- tion please visit our youtube channel by scanning the QR code. And then select your language from the playlist.

Customer Support and Returns

For additional help, contact our technical support. To find your country customer support service, visit: http://security.blaupunkt-service.com
Returns: If you wish to return your camera, we strongly advise that you first delete any camera paired to your account before sending the camera back.

Factory Reset

1. Plug in the camera and wait 1 minute until it boots up.
2. Press the reset button (refer to chapter 2) for 15 seconds until the red Indi-cator light turns on and starts flashing.
3. Wait until the green indicator light flashes slowly.
4. Now the camera is reverted to default settings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>