iCOM OPC-478UC-1 PC Control Programming Cable Instructions

iCOM OPC-478UC-1 PC Control Programming Cable

installation of USB driver

If the automatic USB driver installation is not successful, download the driver from the Icom website and manually install it on the “Device Manager” screen.

1. Go to the Icom website. (https://www.icomjapan.com/support/) In the “Firmware / Software” menu, enter the model name and click the “Search” button to download the latest USB driver. The menu name may be changed without notice.
2. Unzip the file downloaded from the Icom website.
3. Right-click [FT232R USB UART] displayed under “Other devices” on the “Device Manager” screen, and then click [Update driver].
4. “How do you want to search for drivers?” is displayed. Click [Browse my computer for drivers].
5. “Browse for drivers on your computer” is displayed. Click [Browse…].
6. Select the unzipped file in step 2, and then click [OK].
7. Click [Next] to start the installation.
8. After the installation has completed, “Windows has successfully updated your drivers” is displayed. Click [Close].
9. Again, right-click [USB Serial Port], and then click [Update driver].
10. Repeat steps 4 to 8, to install the “USB Serial Port.”
    Confirm the driver availability and the port number on the “Device Manager” screen.

Important

SAVE THESE INSTRUCTIONS — These instructions contain important safety and operating details for the cable.
The programming cable is designed to connect
an Icom transceiver or receiver and a PC for data programming using an Icom programming software. The data cable is designed to connect an Icom transceiver (Rekeying Management transceiver) and a PC for doing the OTAR (Over-The-Air-Rekeying) operation.

Explicit definitions

WORD:  DEFINITION

• WARNING!: Personal injury, fire hazard or electric shock may occur.
• CAUTION Equipment damage may occur.
• NOTE: If disregarded, inconvenience only. No risk of personal injury, fire or electric shock.

Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of:

•  Force majeure includes, but is not limited to, fires, earthquakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination.
• The use of Icom products with any equipment that is not manufactured or approved by Icom.

Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS carefully and completely before using this product.

Precautions

• WARNING! NEVER use or touch the cable with wet hands. This could cause an electric shock.
• CAUTION: USE ONLY INDOORS! NEVER expose the cables to rain, snow, or any liquids.
• NEVER let metal, wire, or other objects touch any internal part of the connectors.
• NEVER place any heavy object on the cable, or pinch it.
• DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the cables.

Disposal

The crossed-out wheeled-bin symbol
on your product, literature, or packaging reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators
(rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area.

System requirements

• Operating System (OS)
  • Microsoft Windows 11 64 bit
  • Microsoft Windows 10 32 bit/64 bit
  • Microsoft Windows 8.1* 32 bit/64 bit
  •  Except for Microsoft Windows RT.
• Others
  • A USB 1.1 or 2.0 port

An Internet connection is required for the USB driver installation.
These instructions are based on using Windows 10.
The displayed dialog boxes, indications, or operations may differ slightly from the following instructions, depending on your operating system, its service pack level, and/or system settings.

Specifications

All stated specifications are subject to change without notice or obligation.

• Usable temperature range:
  • 10˚C to +60˚C (+14˚F to +140˚F)
• Cable length (approximate):
  • OPC-478UC-1 520 mm (20.5 inches)
  • OPC-2363-1 300 mm (11.8 inches)
  • Others 250 mm (9.8 inches)
  • OPC-1637 (USB cable) 1500 mm (4.9 feet)
• Weight (approximate):
  • OPC-478UC-1 37 g (1.3 oz)
  • OPC-966U-1 53 g (1.9 oz)
  • OPC-2344-1 33 g (1.2 oz)
  • OPC-2338-1 57 g (2.0 oz)
  • OPC-2357-1 65 g (2.3 oz)
  • OPC-2363-1 47 g (1.7 oz)
  • OPC-1637 (USB cable) 49 g (1.7 oz)

Supplied accessories

Supplied items

One of the items shown below is supplied.

Programming cable

Data cable

Connecting the cable and USB driver installation

1. Connect the PC to the Internet to download the USB driver.
   Sign in as the administrator.

2. Connect the programming cable or data cable to the OPC-1637 USB cable, and then connect the USB cable to a PC USB port, as illustrated below.

3. The PC automatically installs the USB driver and starts the USB-to-Serial COM Port installation. L Attach the Ferrite EMI filter to the strain relief of the OPC-1637 USB cable.

COM port confirmation

After the driver installation has been completed, confirm the driver’s availability and the port number.
The COM port number is required to set on the programming software.

• Sign in as the administrator.
• Confirm no other applications are running.

1. Right-Click on [Start], and then click [Device Manager].
2. • “Device Manager” is displayed.
3. Click the “>” next to “Ports (COM&LPT).”
4. Confirm “USB Serial Port (COM✱)” is displayed.
5. In this example, the COM port number is “3.”
6. Select the COM port number in the programming software.

NOTE:

• If the COM port is not displayed, double-click [Other devices].
• If the warning symbol “ ” with “FT232R USB UART” is displayed, the driver may not be properly installed. In such case, manually install the USB driver. Refer to the next page for details.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>