afloia Top-Z Physical Dehumidifier User Manual
- June 5, 2024
- afloia
Table of Contents
Physical Dehumidifier Top-Z
User Manual
Dear Customers,
Thank you for purchasing this Physical Dehumidifier! Please keep this User
Manual for your reference. This manual will guide you if you have any
questions or troubleshooting problems
Points for Attention
Before using this product, please read this user manual carefully and keep it for future reference.
Warning
- After the product is powered on, if there is no main body, the indicator will flash white light. After the main body is put on, the indicator will turn on the green light and the machine will start to work. It is a normal phenomenon that hot air flow will occur when the product is working.
- When the product is working, it shall be avoided to be covered with a shelter to avoid product damage.
- When the product is powered on, please keep a distance of more than 10cm from other articles to increase air convection and ovoid product damage.
- If the product is not heated or damaged, it shall be returned to the original factory for maintenance or replaced by professional technicians.
- Do not directly immerse the product in water to avoid damage to the product or electrical leakage.
Note: Children should use the product under supervision and instruction. If you find any abnormality (such as o peculiar smell), please turn off the power as soon as possible, and contact the supplier for maintenance. Please do not repair it on your own to avoid danger.
Notice
- The absorption time of the product will be affected by the environmental humidity, as well as the discoloration speed of the silica gel in the display window.
- After one cycle (2H) of power on reduction, the discoloration rate, and color drop are normal phenomena. If charging for one cycle (2H), the silica gel in the display window still does not change back to orange, which means that the silica gel is not completely dry, please pick up the body for more than 3 seconds, and put it on the base to power on and heat again to ensure that the moisture in the main body is completely removed.
- In the process of delaying heating of the base, if the main body is removed, the base will delay heating for 1 minute before stopping, which is used to release the residual heat of the base. After that time, the indicator will flash white.
Product Overview
Product Description
Silica gel dehumidifier is divided into upper and lower structure designs. The
inner layer of the upper main structure is equipped with silica gel beads with
a moisture absorption function. The lower structure base is equipped with a
heater PTC used to evaporate the wet silica gel beads and a blower that drives
hot air. The used silica gel beads will produce powder, and the outer layer of
the upper structure body is covered with non-woven fabric, which effectively
prevents the leakage of powder. During charging, due to the outer layer of
insulation, the surface temperature of the product can be effectively reduced.
The upper end of the main body is provided with a transparent window. The
display window is equipped with variable-col-or silicone beads, which can
intuitively distinguish the wet or dry conditions of the silicone beads. And
the outer layer design can be placed vertically or horizontally.
Components
Specifications
| Model No. | TOP-Z |
|---|---|
| Product Size | 107x107x273mm |
| Rated Voltage/Frequency | AC100-120V 50/60Hz |
| Power | 50W |
| Working Capacity | 100ML |
| Net Weight | One Pack: 0.83KG±20G Two |
Packs: 1.29KG±20G Dehumidifier
Box: 0.46KG±20G Heating Base: 0.37KG
Dehumidifying Material| SlO2
Function Instruction
Check before power on
A: Whether the power cord is in good condition;
B: Whether the silica gel in the display window is orange;
C: Whether the output voltage of the power socket is consistent with the
voltage of this product.
Usage
When using it for the first time, please check whether the silica gel in the
display window is orange or not. If it is orange, there is no need to restore
it. If it is black, please put it on the base and power it on until it is
orange.
- When the power is on, the indicator flashes white light. When the main body is placed on the base, the indicator always lights green.
- When the silica gel in the main display window is orange, it means that the product can start dehumidification, which can be placed in the closet, cabinet, and other spaces to absorb moisture.
- When silica gel in the display window is black, it means that the product has been full of moisture. Put the product on the base, after heating for two hours, the machine will automatically cut off the heating module and enter standby mode. The indicator will flash white, which means that a working cycle is completed. When the silica gel in the display window changed to orange, which means that the silica gel has been completely dry. The product can be reused for dehumidification.
Notice: Due to the different use environment, if charging for one cycle (2H), the silica gel in the display window still does not change back to orange, which means that the silica gel is not completely dry, please pick up the body more than 3 seconds, and put it on the base to power on and heat again to ensure that the moisture in the main body is completely removed.
Inquiry about Malfunction
Product parts may wear out due to heat, moisture, dust, and other causes over
time, which may cause malfunction of the product.
If there is any malfunction, do not use the product. Please unplug the unit
and contact customer@afloia.com
Warranty
For questions about our warranty or to look at our other products, please
visit our website: www.afloia.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>