BLAUPUNKT P1PM2T2 EV Portable Charger User Manual
- June 6, 2024
- Blaupunkt
Table of Contents
BLAUPUNKT P1PM2T2 EV Portable Charger
EV Portable Charger
Please carefully read the fol lowing instructions before charging your
Electrical Vehicle, be aware of the hazards involved with electrical circuity
and standard practices for preventing accidents.
Introduction to t he Portable EV Charger ( Mode 2)
CAUTION
- Use the power source with external upstream Circuit Breaker.
- Make sure the charger is used in a safe, secure place and well out of the reach of young children or pets.
- Please use the charger in a dry, well ventilated and secure place. Keep weel out of reach of young children or pets. Avoid water pouring directly onto the power plug.
- Do not open the enclosure while charging or with the power on.
- Do not maliciously damage the product.
Specifications
Model Power Supply Cable Total Voltage Current Connector Type
P1PM2T2 Single-phase 8m 220-2S0V 8/10/l
3/16A T2
P1PM2Tl Single-phase 8m 220-250V 8/1 0/l
3/16A Tl
P1PM2T2C Single-phase 8m 220-250V 8/10/l 3/l 6A
T2
P3PM2T2 Three-phase 8m 380-450V 8/10/13/16A
T2
P1PM2T2BS Single-phase 8m 220~250V 8/10/l 3/l 6A
T2
PlPM2TlBS Single-phase 8m 220~250V 8/10/l 3/16A
Tl
Explanation of the operating display and technical parameters
Model: P3PM2T2
Technical Parameters
Dimensions (LxWx H) 260x l00x 72.5 mm
Weight 3Phase: 3.35 kg
Protection Degree ( Control box) IP65
Operating Temperature · 30″C to +SO”C
Model: Pl PM2T2 / Pl PM2Tl / Pl PM2T2C / Pl PM2T2BS / Pl PM2Tl BS
Technical Parameters
Dimensions (L x W x H) 260x 100×72.Smm
Weight 1 Phase: 2.65 kg
Protection Degree ( Control box) IP65
Operating Temperature -30°C to +SO”C
Use of the charger
Start Charging
DANGER
- Do not use the product ifit appears to be damaged or the cable is broken.
- Do not disassemble or assemble the connector and change the internal parts
- Do not clean the products using chemicals or cleaning the EV car while charging.
Stop Charging
Display Light Status
Display Light Status
Operation
Troubleshooting
Single Phase use
The portable charger will work if used via an adapter from a single-phase wall
socket. If using an adapter, please make sure it is suitable for EV charging –
approved for minimum 16A.
If the charger is connected to a single-phase wall socket via an adapter, it
is important to make sure the wall socket is suitable for EV charging –
approved for minimum 16A.
If used via an adapter in a wall socket with ground connection the functions
of t he portable charger are identical to three phase use.
If used via an adapter in a wall socket without ground connection, press
“AMPS’ and”TIME”for two seconds after firmly connecting the portable charger
to the wall socket The portable charger should not be connected to the vehicle
at this stage.
After pressing”AMPS and’TIME” for 2 seconds insert the charging connector into
the electric vehicle. switch the power from the wall socket off and on again .
Now the portable charger will be able to charge without a ground connection.
Please note that many Electric Vehicles require ground connection to start the
charging process.
Function
Switch Current
CAUTION: In order to switch charging current, Please make sure the power plug is firmly inserted into the socket and plug for the EV vehicle is disconnected.
Please complete setting within 4 seconds at each step, otherwise the feature setting will fail.
Timer function
CAUTION In order to switch charging current, Please make sure the power plug is firmly inserted into the socket and the plug for EV vehicle is disconnected.
Please complete setting within 4 seconds at each step, otherwise the feature setting will fail.
Notice:
In case you want to cancel the timer setting -you can use one of the two
options below:
- Directly to disconnect the plug from the outlet socket
- Press the Time button for Ss.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>