Shenzhen Wedoinnov POD5 Wireless Conference Speakerphone User Manual

: June 6, 2024
: Shenzhen Wedoinnov

Table of Contents

What’s in the box
Overview
Easy Set-Up
FCC Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Wedoinnov Speakerphone

User Manual

What’s in the box

|
---|---
Wireless Speakerphone X 1| Expansion Microphone X 2
|
User Manual X 1| USB Cable X 1

Overview

Easy Set-Up

On/off Long press ON/OFF for 2s, the device will be turned on/off, with beep notice.
Connect to speak 200 USB & BT
2.1 Connect by Bluetooth
Press the Bluetooth button for 2 seconds to start Bluetooth pairing mode. It will be alternate white and blue flashing light.
2. Turn on the Bluetooth on your device and choose to connect with the Speakerphone. After connection, it will be a white flashing light with a hinting tone. While Bluetooth is disconnected, the light will be blue with a hinting tone.

2.2 Connect by USB
Connect Speak 200 USB & BT with computer by USB cable. After connection, the green circle light will increase clockwise one by one showing charging status. Green circle light will be on in full when charging is completed.

2.3 Connect by Wireless Receiver
Connect the USB wireless receiver to your computer, and start Bluetooth pairing mode on the speakerphone. Wait for about 10 seconds until the pairing is completed, then the speakerphone is connected and ready to go.

3. Audio source switching function
When the device is connected by Bluetooth and USB simultaneously, short press / tap the Bluetooth button **to switch between Bluetooth and USB transmission.
4. Answer /end calls
Press the button to answer calls, press the button to end calls.
5. Volume increase/decrease
When volume increase + /decreases —, the green lights will be on/off one by one. When adjustment is completed, lights will be off after 4s.
6. Mute
6.1 Press Mute microphone audio input will stop.
6.2 Long press the mute key for about 2s to switch Microphone short-distance mode: Microphone short-distance mode is for eliminating surrounding noise automatically and only voice within a radius range of 1.5 meters will be picked up and transmitted. Also, speaker volume will be adjusted automatically according to surrounding noise. VoiceCap model is only suggested in open space. Please disable this function when in conference rooms.
7. Auto Power Of
When the device is not connected by Bluetooth or USB in 15mins, it will shut down automatically.
8. Power indicator**
When the device is not connected by USB, short press/tap power button the green circle light will indicate power condition.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure condition without restriction.