VANKYO Burger 101 Wireless Pico Projector Rechargeable Mini DLP Projector User Manual

VANKYO Burger 101 Wireless Pico Projector Rechargeable Mini DLP Projector User Manual

PACKING LIST

NOTICE

FUNCTION OVERVIEW

GETTING STARTED

1. Turn On

   • Plug the power cable into the projector and the socket.
     

   • Switch the ON/OFF Switch to ON.
     

   • Press the Power button to turn the projector on.

2. Turn Off

   • Press the Power button once, then select Confirm to turn off the projector.
   • Switch off the ON/OFF Switch to OFF.

3. Battery
   This projector is equipped with the built-in Li-ion rechargeable battery which can provide power supply to other mobile devices through the USB port when needed.

4. Charging
   Fully Charged: LED Off
   Charging: Blue LED

IMPORTANT:

• To avoid turning on the projector accidently which may lead to electrical fires, switch the ON/OFF Switch to OFF.
• Do not use it as a projector and power bank at the same time.
• Always connect your projector to power or charge it timely when the battery is low.

FOCUS AND KEYSTONE

Slightly adjust the focus ring on the projector to get the best image.

The projector supports automatic vertical Keystone correction within a degree of ±40.

WIFI CONNECTION

1. Go to Homepage > Setup > Network > WiFi, then select Scan to display the WIFI list.
2. Press the Up/Down button to select your WIFI, then press the OK button to continue.
3. Enter the correct password, then select Confirm to get Internet connection.

MULTIMEDIA CONNECTION

Projecting from a USB Disk

1. Turn on the projector and insert your USB disk into the USB port.

2. Go to Homepage to select Media, it will display an interface for projecting from a USB Disk.
   
   

3. Select the category of the file you would like to project accordingly.

   • To play the video, select Movie, then find your video file and play it by pressing the OK button. To watch 3D video, please press the 3D button on the remote when playing it (30 video source is required and 3D glasses are not included).
   • To play the audio file, select Music to find your audio file. Select it first by pressing the OK button, then select the Play option to start playing.
   • To project photo, select Photo, then find your photo and play it by pressing the OK button.
   • To project text, select Text, then find your text file and open it by pressing the OK button.

Different File Formats Supported

Text Format Supported: TXT
Image Format Supported: JPG/JPEG/BMP/PNG
Audio Format Supported: MP1/MP2/MP3/WMA/WAV/OGG/FLAC/AAC/M4A
Video Format Supported: MPEG1/MPEG2/MPEG4/H.264/MVC/H.263/DAT/MPG/V0B/TS/AVI/MKV/MP4/MOV/3GP/FLV

Projecting from HDMI Input Connection

1. Turn on the projector, then connect the projector to your device with the provided HDMI cable.
2. Go to Homepage, then select HDMI to project the contents from your device to the screen/wall.
   

Play Videos in KOALA and YouTube

Go to Homepage > KOALA/YouTube to play videos after the projector is connected to your WIFI.
Tip: Press the Menu button on the remote to get back to the Home Page of KOALA/YouTube.

SCREEN MIRRORING

For iOS System

1. Connect your iOS device and the projector to the same WIFI network.

2. Go to Homepage > iOS Cast to display the following interface.
   

3. Swipe your iOS device up, then tap Screen Mirroring/AirPlay Mirroring and search for the projector.

4. Select ZYCast- xxxx (icast) from the searching list.

5. Your iOS device display will be projected on the wall/screen.

For Android system

To activate this function, please make sure your android device supports Multi-screen/Wireless display. Names may differ from different Android devices.

1. Turn the WIFI to ON status in the settings of your Android device. To make a smoother streaming, please do not connect to any WIFI on your projector.

2. Go to Homepage > Miracast to enter the following interface.
   

3. 3. Activate Multi-Screen function in your Android device and search for the projector.

4. Select ZYCast-xxxx (mcast) from the searching list.

5. Your Android device display will be projected on the wall/screen.

SCREEN CASTING (For iOS System Only)

1. Connect your iOS device and the projector to the same WIFI network.
2. Select Setup on the homepage, enter Advanced > iOS Play Mode, then press the right button on the remote to select screen casting HD/SD.
3. Go to Homepage > iOS Cast on the projector.
4. Launch a video player on your iOS device and select a video to play.
5. Tap  > Airplay & Bluetooth devices > ZYCast-XXXX (icast) to cast the video on your iOS device to the wall/ screen via the projector.
   

Tips:

1. Once the video is casted to the wall/screen, you can close the app and do other things without interrupting the video as long as your iOS device is still connected.
2. Always connect your projector to power.

SETTINGS

Go to Homepage > Setup to adjust the settings of your projector.

Network
Connect the projector to your WIFI.

Projection
Set up brightness mode, brightness level, projection mode, Keystone configurations etc..

Advanced
Change language, select boot source, set up sleep timer, select Jos Play Mode, update firmware, make a factory restore, etc.

Information
Check the memory, software version, etc.

SPECIFICATION

TROUBLESHOOTING GUIDE

1.  The content on my iPhone can’t be mirrored on the projected screen.
   • Make sure your iPhone is connected to the same 2.4G network as your projector.
   • Go to Setup > Information > Software Version to check the version of your projector, then contact support@ivankyo.com for further assistance.
2. The projector cannot be turned on when I press the power button. ‘ Connect the projector to the socket with a power cord to check whether the built-in battery is empty.
   • Make sure you switch the ON/OFF Switch to ON.
3. The projected image freezes or the projector is not responsive.
   • Go to Setup > Advanced to make a factory reset.
4. 3D effect is not working as expected.
   • The 3D active shutter glasses are required.
   • Make sure the 30 video is in the format of side-by-side or top and bottom.
   • Make sure to press the 3D button on the remote.
5. My USB disk or hard drive can not be read.
   • Make sure the format of your USB disk or hard drive is FAT32 or NTFS.
   • The max. storage of the USB disk should be less than 64GB.

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISEDC Warning

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. The minimum distance from body to use the device is 20cm.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

The symbol indicates DC voltage

RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. This product can be used across EU member states.

VANKYO SUPPORT

North America : support@ivankyo.com
United Kingdom : support.uk@ivankyo.com

www.ivankyo.com

@VankyoOfficial

VANKYO

Documents / Resources

| VANKYO Burger 101 Wireless Pico Projector Rechargeable Mini DLP Projector [pdf] User Manual
Burger 101 Wireless Pico Projector Rechargeable Mini DLP Projector
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>