jakks PACIFIC 409842 XPV BladeSaw Instructions

jakks PACIFIC 409842 XPV BladeSaw Instructions

BATTERY INSTALLATION INSTALLATION DES PILES

ADULT INSTALLATION REQUIRED INSTALLATION DEVANT ÊTRE CONFIÉE À UN ADULTE

When performance diminishes, replace with fresh batteries.
Requires (x6) 1.5 V “AA” (LR6/R6) (included) and (x2) 1.5 V “AA” (LR6/R6) batteries. (not included)
Included 6 “AA” batteries for Try-me purpose only.

VEHICLE

Included 6 “AA” batteries for Try-me purpose only.
Replace with 6 new “AA” (LR6/R6) batteries and detach the wires on both.

CONTROLLER MANETTE

IMPORTANT SAFETY INFORMATION

NEVER use near glass and other fragile objects.
NEVER operate during storms or other adverse weather conditions.
ALWAYS point away from face, eyes, people, animals and property when driving.
ALWAYS use alkaline batteries only.

OPERATION MODE D’EMPLOI

1. VEHICLE: Move the ON/OFF switch to the ON position

2. CONTROLLER: Move the ON/OFF switch to the ON position. The indicator light will light up.

3. Place the VEHICLE on ground and point the CONTROLLER directly at the VEHICLE. The LED light on CONTROLLER will flash when pairing with the VEHICLE. Pairing process is completed when the LED light is on solid. Use the FORWARD/REVERSE controls to maneuver the VEHICLE. Pairing is required every tie the VEHICLE/CONTROLLER is turned on. Note: When LED light on CONTROLLER keeps flashing, switch off both VEHICLE and CONTROLLER and repeat

CONTROLS CO MMANDES

FORWARD MARCHE AVANT

REVERSE MARCHE ARRIÈRE

TURN RIGHT IN FORWARD TOURNER À DROITE

,

TURN LEFT IN FORWARD TOURNER À GAUCHE

,

OPEN WHEEL / CLOSE WHEEL OUVRIR LA ROUE / FERMER LA ROUE

PRESS THE WHEEL ON THE CONTROLLER APPUYER SUR LA ROUE\ SUR LA MANETTE

TRIM CONTROLS
COMMANDES DE COMPENSATION

(NOTE: Adjust if vehicle is drifting left or right when driving forward.)

Move the TRIM CONTROL LEVER toward the “L” position. Test and repeat until vehicle is driving straight.

Move the TRIM CONTROL LEVER toward the “R” position. Test and repeat until vehicle is driving straight.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device.

TROUBLESHOOTING

PROBLEM

|

POSSIBLE CAUSE

|

SOLUTION

---|---|---
Vehicle won’t move.| Vehicle/Controller is switched OFF.| Move switch to ON position.
Weak Battery in Controller/Vehicle.| Ensure the batteries in the controller and vehicle are fresh.
Controller is not close enough to vehicle.| Make sure the Controller is placed within the signal receiving range.
Vehicle is stuck.| Move vehicle to a smoother surface, clean wheels, and/or
Vehicle will not go in a straight line.| Trim Control may need adjusting.| See instructions (page 4) on how to adjust the Trim Control.

WARNING! Battery acid leakage can cause personal injury and cause damage to the product and surrounding property. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. Leaking batteries may make “popping” sounds. Always remove replaceable batteries before dispolsing product. Dispose batteries or products with non-replaceable batteries according to Local, State or Federal Battery and Recycling Laws.

Read More About This Manual & Download PDF:

References

• Home - JAKKS Pacific, Inc.
• Warranty - JAKKS Pacific, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>