Jakks Pacific 652314 RC Speed Demo Radio Controlled Car Instruction Manual
- June 5, 2024
- jakks PACIFIC
Table of Contents
Jakks Pacific 652314 RC Speed Demo Radio Controlled Car
BATTERY INSTALLATION
CAUTION : ALWAYS HAVE THE ON/OFF SWITCH IN THE “OFF” POSITION WHEN
R/C VEHICLE
- LOCATE BATTERY COVERS ˜X2° ON TOP AND BOTTOM OF VEHICLE.
- USING A PHILLIPS HEAD SCREWDRIVER ˜NOT INCLUDED
- LOOSEN THE SCREWS AND REMOVE THE BATTERY COVERS ˜X2°
- INSTALL 4 “AA” ˜LR6/R6° BATTERIES, AS SHOWN.
- REPLACE THE BATTERY COVERS AND TIGHTEN THE SCREWS.
THE VEHICLE REQUIRES BATTERIES ON BOTH SIDES TO OPERATE. FLIP R/C VEHICLE OVER AND REPEAT STEPS.
CONTROLLER
- LOCATE BATTERY COVER ON BACK OF CONTROLLER.
- USING A PHILLIPS HEAD SCREWDRIVER
- NOT INCLUDED°, LOOSEN THE SCREW AND REMOVE THE BATTERY COVER.
- INSTALL 2 “AA” ˜LR6/R6° BATTERIES, AS SHOWN.
- REPLACE THE BATTERY COVER AND TIGHTEN THE SCREW.
BATTERY SAFETY INFORMATION
WARNING! Battery acid leakage can cause personal injury and cause damage to the product and surrounding property. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. Leaking batteries may make “popping” sounds. Always remove replaceable batteries before disposing product. Dispose of batteries or products with non-replaceable batteries according to Local, State or Federal Battery and Recycling Laws.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: Changes or modiÿcations to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment. NOTE: This equipment has been tested and found to comply with
the limits for Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment o˜ and on, the user is encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit di˜erent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B)/NMB-3(B)
SAFETY INFORMATION
- NEVER DRIVE A VEHICLE IN PARKING LOTS, NEAR ROADS, PETS, OR CARS
- NEVER PICK UP THE VEHICLE WHILE IT IS IN MOTION.
- NEVER OPERATE THE VEHICLE WITH ANYTHING OTHER THAN FLY WHEELS™ WHEELS.
- NEVER OPERATE THE VEHICLE WITHOUT A TIRE ATTACHED.
- NEVER OPERATE A VEHICLE WITH MISMATCHED RIM AND TIRE SIZES.
- NEVER STEER INTO OTHER OBJECTS. IMPACT MAY DAMAGE THE VEHICLE.
- NEVER DRIVE THROUGH WATER OR MUD AS THE VEHICLE IS NOT WATERPROOF.
- ALWAYS KEEP FINGERS, HAIR, AND EYES AWAY FROM THE WHEELS WHILE THE VEHICLE IS IN THE “ON” POSITION
- ALWAYS PLAY IN SAFE SURROUNDINGS, AWAY FROM STREETS OR MOVING VEHICLES.
- ALWAYS REMOVE FURNITURE AND OTHER OBJECTS FROM THE AREA BEFORE PLAYING.
- ALWAYS KEEP THE ON/OFF SWITCH IN THE “OFF” POSITION WHEN THE TOY IS NOT IN USE.
- ALWAYS OPERATE THE CONTROLLER WITHIN 82’ (25 M) OF THE VEHICLE.
MOVE THE ON/OFF SWITCH ON THE R/C VECHICLE TO THE ON POSITION.
MOVE THE ON/OFF SWITCH ON THE CONTROLLER TO THE ON POSITION.
PAIRING SUCCESSFUL
HOLD CONTROLLER NEXT TO R/C VEHICLE
- 12 INCHES
- 305MM OR CLOSER
- LED ON CONTROLLER WILL CHANGE FROM BLINKING TO SOLID WHEN PAIRED.
- IF THE UNITS FAIL TO PAIR,
- TURN THEM BOTH OFF, AND REPEAT STEPS 1 or 3 AGAIN.
OPERATION
- THE RC VEHICLE MOVES, TURNS AND FLIPS OVER.
- WHEN THE VEHICLE FLIPS, THE CONTROLS WILL OPERATE IN THE OPPOSITE FUNCTION, AS SHOWN BELOW.
- PUSH BOTH CONTROLS UP
- PUSH BOTH CONTROLS DOWN
- PUSH LEFT CONTROL DOWN. PUSH RIGHT CONTROL UP.
- PUSH LEFT CONTROL UP. PUSH RIGHT CONTROL DOWN.
CHANGE WHEELS AND CUSTOMIZE THE PERFORMANCE
LEFT WHEEL
- LIFT UP AND HOLD TAB LOCATED ON FRONT OF
- REMOVE WHEEL FROM VEHICLE.VEHICLE TO UNLOCK WHEEL.
- GENTLY TWIST COUNTER-CLOCKWISE.
RIGHT WHEEL
- LIFT UP AND HOLD TAB LOCATED ON FRONT OF VEHICLE TO UNLOCK WHEEL.
- GENTLY TWIST COUNTER-CLOCKWISE.
- REMOVE WHEEL FROM VEHICLE.
WHEEL INSTALLATION
LEFT WHEEL
-
ALIGN TABS ON RC VEHICLE TO GROOVES ON WHEEL’S INNER HUB. • SLIDE WHEEL ONTO THE VEHICLE.
NOTE: ONLY FLY WHEELS™ WHEELS WORK WITH THE VEHICLE. DIFFERENT WHEELS AND TIRES WILL AFFECT PERFORMANCE. -
GENTLY INSERT AND TWIST THE WHEEL CLOCKWISE UNTIL IT LOCKS INTO PLACE.
RIGHT WHEEL
-
ALIGN TABS ON RC VEHICLE TO GROOVES ON WHEEL’S INNER HUB
-
SLIDE WHEEL ONTO THE VEHICLE.
NOTE: ONLY FLY WHEELS™ WHEELS WORK WITH THE VEHICLE. DIFFERENT WHEELS AND TIRES WILLAFFECT PERFORMANCE. -
GENTLY INSERT AND TWIST THE WHEEL CLOCKWISE UNTIL IT LOCKS INTO PLACE.