Jakks Pacific 41822TXNT Super Mario Racer User Manual

Jakks Pacific 41822TXNT Super Mario Racer

Product Information

Specifications

• Controller (41822TXNT): Requires x2 1.5V AA (LR6) alkaline batteries (not included)
• Racer (41822RXNT): Requires x6 1.5V AA (LR6) alkaline batteries (not included)
• Maximum Transmission Power: 0.251 mW (-6 dBm)
• Frequency Band: 2405-2475MHz

Product Usage Instructions

Battery Installation

1. Using a Phillips Head screwdriver (not included), remove the BATTERY cover on the RACER and CONTROLLER.
2. Detach the wires on both the RACER and CONTROLLER.
3. Insert fresh x6 1.5V AA (LR6) alkaline batteries into the RACER.
4. Insert fresh x2 1.5V AA (LR6) alkaline batteries into the CONTROLLER.
5. Replace the battery covers on both the RACER and CONTROLLER.

• Make sure RACER is in OFF position. Locate BATTERY COVER underneath RACER as shown. Use a Phillips Head screwdriver (not included) to loosen screws and remove cover.

• Install 6 – 1.5V AA (LR6) ALKALINE BATTERIES in the orientation shown.

• Replace BATTERY COVER and tighten screws.

Power Switch
To turn off the RACER, push the power switch to the ‘OFF’ position.

• CONTROLLER (41822TXNT): x2 1.5V AA (LR6) ALKALINE BATTERIES REQUIRED NOT INCLUDED
• RACER (41822RXNT): x6 1.5V AA (LR6) ALKALINE BATTERIES REQUIRED NOT INCLUDED
• Maximum Transmission power: 0.251 mW(-6 dBm), 41822TXNT: 0.251 mW (-6 dBm), 41822RXNT: 0.265 mW(-5.77 dBm)
• Frequency Band: 2405-2475MHz
  Includes 6 AA (R6/LR6) Batteries. Batteries are for “Try Me” purpose only. Unplug the cable on the Racer and Controller. Remove the Racer’s AA (R6/LR6) batteries and replace with fresh batteries.

TRY ME BATTERIES REMOVAL

1. Open up box and remove the RACER and CONTROLLER from the box.
2. Remove inner packaging until RACER and CONTROLLER are as shown above.
3. Using a Phillips Head screwdriver (not included) remove the BATTERY cover on the RACER and CONTROLLER and detach the wires on both.
4. Push the power switch of the RACER to “OFF’ position. Remove the Racer AA batteries. Install fresh batteries in the RACER and CONTROLLER and replace the battery covers on both. (see BATTERY INSTALLATION.)

OPERATING THE RUMBLE RC RACER

1. Turn the CONTROLLER power switch to the “ON” position.
2. Turn the POWER switch on the bottom of the RACER to the “ON” position.
3. When the RACER and CONTROLLER are turned ON, the power light on the CONTROLLER will flash to sync with the RACER. When the power light stops flashing and remains ON , the sync is complete.

• Push the ON/OFF/TRY ME button to the ON position

• Front Wheel Knob – Turn the knob left or right to fine-tune the front wheel steering angle.

IMPORTANT SAFETY INFORMATION

Caution: Not recommended for children under 4 years of age. Read instructions before operating. Avoid hitting people, pets or home furnishings. Never operate in the street. Keep hair, hands and clothing away from vehicle when power switch is turned ON. DO NOT pick up moving vehicle. Remove batteries and controller batteries when vehicle is to be stored for an extended period. Do not store in direct sunlight. VEHICLE WORKS BEST ON SMOOTH, FLAT, CLEAN, DRY SURFACES, FREE OF DIRT AND DUST. NOT INTENDED FOR USE ON CARPET.

STANDARD DRIVING MODE / (FR) MODE DE CONDUITE STANDARD
Shift LEFT stick to go FORWARD/REVERSE. Shift RIGHT stick to go LEFT/RIGHT.

MARIO HEAD AND ARM ROTATION
Shift and hold the RIGHT stick in either direction.

EXHAUST PIPE RUMBLING
Shift LEFT stick to go FORWARD/REVERSE.

TROUBLESHOOTING

battery connector
Vehicle or controller switch not “ON”| Move switch to the “ON” position
Vehicle battery weak| Replace with fresh batteries
Weak transmitter (controller) battery| Replace with fresh batteries
Signal is out of range| Move the controller close to the Racer
Electrostatic discharge occurs| Reset the Racer and Controller by turning OFF and back to ON again
Erratic or only short range operation| Radio interference| Change location of operation
Weak transmitter battery| Replace with fresh batteries

BATTERY SAFETY INFORMATION

(EN) BATTERY SAFETY INFORMATION
WARNING! Battery acid leakage can cause personal injury and damage to product and surrounding property. If battery leakage occurs, thoroughly wash any aected skin, keeping battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. Leaking batteries may make “popping” sounds. Always remove replaceable batteries before disposing product. Dispose batteries or products with non-replaceable batteries according to battery and recycling laws. Batteries included are for “Try Me” purposes. If performance diminishes after purchase, replace with fresh batteries.

TO AVOID BATTERY PROBLEMS

• NEVER mix old and new batteries or different brands of batteries.
• NEVER mix alkaline, standard (carbon-zinc), rechargeable batteries with this product.
• NEVER dispose of batteries in fire, as they may leak and explode.
• ALWAYS remove batteries when exhausted or unused for a long time.
• ALWAYS have an adult install batteries consistent with installation instructions.
• ONLY use batteries specified by manufacturer.
• Insert batteries with correct polarity (+ and -).
• Do not short-circuit supply terminals.
• Do not recharge non-rechargeable batteries.
• Remove rechargeable batteries from toy before charging.
• Charge rechargeable batteries only under adult supervision.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions

1. this device may not cause interference, and
2. this device must accept any interference including interference that may cause undesired operation of the device.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

CONTROLLER BATTERY INSTALLATION

ADULT INSTALLATION REQUIRED
Requires 2 – 1.5V AA (LR6) ALKALINE BATTERIES. Batteries not included. When performance diminishes, replace with fresh batteries.

1. Locate and open BATTERY COVER as shown. Use a Phillips Head screwdriver (not included) to loosen screw. Screw remains attached to cover.
2. Install 2 -1.5V AA (LR6) ALKALINE BATTERIES in the orientation shown.
3. Replace BATTERY COVER and tighten screw.

Frequently Asked Questions

1. Q: What type of batteries does the controller need?
   A: The controller requires x2 1.5V AA (LR6) alkaline batteries.

2. Q: How many batteries does the racer need?
   A: The racer requires x6 1.5V AA (LR6) alkaline batteries.

3. Q: What is the maximum transmission power?
   A: The maximum transmission power is 0.251 mW (-6 dBm).

4. Q: What is the frequency band?
   A: The frequency band is 2405-2475MHz.

©2023 and manufactured for / fabriqué pour JAKKS PACIFIC, INC., 2951 28TH ST., SANTA MONICA, CA 90405 USA.

Other trademarks used under license

MADE IN CHINA
Imported into UK by / Importé au Royaume-Uni par JAKKS Pacific (UK) Ltd., 1 Arlington Square, Downshire Way, Bracknell, Berkshire RG12 1WA, GB, and EU by / et UE par JAKKS Europe B.V., Herikerbergweg 88, 1101 CM Amsterdam NL. www.jakks.com www.jakks.com/warrantyconsumers@jakks.com

North America:   1.877.875.2557 or 1.909.594.7771 UK & EU / Royaume-Uni et UE: 00.44(0)1344.638909 Mexico: 52.557.1556612

• Product may be patented. Details at jakks.com/patents.
• Colors & decoration may vary. Retain packaging/instructions for reference.
• Remove all packaging before giving toy to child.

WARNING: Small Parts. Choking Hazard.
© Nintendo and Universal City Studios LLC. All Rights Reserved

References

• Patents - JAKKS Pacific, Inc.
• Home - JAKKS Pacific, Inc.
• Warranty - JAKKS Pacific, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>