BLAUPUNKT CMP312 Pressure Coffee Maker Owner’s Manual

BLAUPUNKT CMP312 Pressure Coffee Maker

OVERVIEW

Important notes

• To achieve the utmost in enjoyment and performance, and in order to become familiar with its features, please read this manual carefully before attempting to operate this product.

• Before using this device read the instruction manual and follow the instructions inside. The manufacturer is not liable for any damages caused by the misuse of this device due to inappropriate handling. Please keep this manual for future reference.

•  This device is for domestic use only. Do not use for any other purposes.

•  The device should only be connected to an earthed socket with values corresponding to the values on the rating label. It is necessary to check, if total current consumption of all devices plugged into the wall outlet does not exceed the fuse in the circuit.

•  If you are using an extension cord, make sure that the total power consumption of the equipment plugged into the extension cord does not exceed the extension cord power rating. Extension cords should be arranged in such a way as to avoid tripping hazards.

•  Make sure the cable is grounded, 3-cores with a socket and an earth cable.

•  Do not let cord hang over edge of counter, or touch any hot surface.

•  The device is not designed to be controlled via an external timer, separate remote control, or other equipment that can turn the device on automatically.

•  Before maintenance work always disconnect the unit from the power supply.

•  When unplugging the power cord from electrical outlet, hold it by the plug only and remove the plug carefully. Never pull the cable as it may cause damage to the plug or power cord.

•  Damage to the power cord or plug can lead to an electrocution hazard.

•  Never leave the product connected to the power source without supervision.

•  Never put the power cable, the plug or the whole device into the water or any other liquids. The device should be cleaned regularly complying with the recommendations described in the section on cleaning and maintenance.

•  Do not place the device near sources of heat, flame, an electric heating element or a hot oven. Do not place on any other device.

•  This equipment can be used by children aged 8 years and over under as long as supervision is provided. People with reduced physical or mental capabilities, as well as people with no previous experience of using this equipment must be supervised and made aware of the risks. The instruction manual should be used as a reference for the safe use of this equipment. Children should not play with the equipment.

•  Children without ensured supervision should not be allowed to perform the cleaning and maintenance of equipment.

•  Additional precautions should be taken when using this device in the presence of children or pets. Do not allow children to play with the device.

• Never use the product close to combustibles.

•  Never expose the product to atmospheric conditions such as direct sun light or rain, etc. .. Never use the product in humid conditions (like bathroom or camping house). The power cable should be periodically checked for damage.

•  If the power cable is damaged the product should be taken to a professional service location to be fixed or replaced to prevent any hazards from arising.

•  Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product by yourself as it can lead to electric shock. Always return the damaged device to a professional service in order to repair it.

•  All the repairs should only be performed by authorized service professionals. Any attempted unauthorised repairs performed can be a hazard to the user.

•  Only Original accessories should be used, as well as accessories recommended by the manufacturer. Using accessories which are not recommended by the manufacturer may result in damage of the device and may render the device unsafe for use.
  Make sure that device is unplugged before you fill the water tank.

•  Never use the device when the water tank is empty. Water tank must be filled only with pure and cool water. Do not fill the water tank beyond max capacity.

•  Water tank lid should not be opened while the device is working.

•  Do not place hands directly under the steam, hot water or coffee pour as this can lead to a scalding and injury.

•  Never remove the filter holder when brewing coffee or collecting boiling water because the appliance is under pressure. Removing the filter holder may result in injury.

•  Never touch the filter holder or the milk frothing nozzle while the appliance is in operation, as this may cause burns.

•  Never turn the steam control button rapidly, as the steam

•  Do not move steam wand out from the frothed milk until steam control knob is closed.

•  Before cleaning, always disconnect the espresso machine from the power supply and wait until all hot parts have cooled down.

Device is compliant with EU directives:

•  Low voltage directive (LVD)
•  Electromagnetic compatibility (EMC)

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Used appliance should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose this appliance In the common waste bin.
Your products is designed a manufactured with high quality materials and components, which can be recycled and reused. Environmental information unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box),polystyrene foam(buffer) and poly ethylene (bags, protective foam sheet). Your system consists of material which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Technical data

• Power supply: 220-240V-50Hz
• Power:850W
• Water tank capacity: 1,61

1.  On/Off switch
2.  Coffee switch
3.  Steam switch
4.  Cup cushion
5.  Drip tray
6.  Steam co
7. rol knob
8.  Water tank cover
9.  Detachable water tank
10.  Cup warmer
11.  Steam tube
12.  Steam tube jacket
13.  Filter holder’s mounting point
14. Filter holder handle
15.  Stainless steel filter
16.  Press bar with spoon
17.  Filter holder
18.  Barometer

Before first use

It is recommended to rinse the coffee maker before the first use. The coffee maker should also be rinsed after a longer period of time without use. Refer to the instruction in the”Cleaning and maintenance” chapter. NOTE : When water system is empty, the water pump may work louder and device may vibrate more. This is a common occurrence which will disappear after a given period of time.

Preparation of espresso coffee

1.  Turn device on by pressing the On/Off switch [1 ]. Coffee maker will start to pre-heat, LED will blink.
2.  Choose the right filter [14 ] (for one cup, for two cups) and put it into the filter holder [16]
3.  When coffee maker is ready, the LED will stop blinking and shine continuously.
4.  Hold the filter holder [16] with filter inside [14] below the mounting point [12] and rinse it with water to pre-heat it. Press the button “coffee switch” [2] and wait for a few seconds, than press “coffee switch” again to close the flow of the water.
5.  Pour medium ground coffee powder into the filter [14] and pack the coffee gently. Clean the rim of the filter holder [16] to remove any excess ground coffee. ADVISE 1. Coffee ground too fine (like for brewed coffee), will block the flow of the water in the filter. Coffee ground too coarse, will not release the full flavor and aroma of the coffee. ADVISE 2. If coffee is packed too tightly, the flow of water can be obstructedand may scold the coffee and cause the drink to have a burned aroma. It may even block the flow of water totally. If the coffee is packed too loose it will not transfer enough taste and aroma into the drink.
6.  Place the filter holder [16] into the mounting point head [12]. Engravings on the filter holder must fit in the slots of the filter holder’s mounting point. Turn the filter holder all the way to the right (clockwise).
7.  Place cups under the outlets of the filter holder.
8.  Press “coffee switch” [2] and wait for the right amount of coffee to pour into the cups thenpress”coffee switch” [2] again.

Frothing milk

It is advised to froth the milk after the coffee had been prepared as milk frothing mode requires a higher temperature. After milk frothing it is necessary to wait a minimum of 5 minutes to allow the device to cool down slightly. If the temperature of brewing is too high, the coffee can be scolded which will cause the coffee to have a burned and bitter taste and aroma. Before frothing ensure the volume of milk is adequate in the cup. Milk can double in volume after frothing, so care should be taken when deciding the volume of milk. Use a heat-resistant cup for milk frothing. The cup can get very hot during frothing.

1.  Turn on the milk frothing mode by pressing “steam switch”[3]. The LED control light will start to blink. When the light starts to shine continuouslythe device is ready to generate steam.
2.  Rinse the steam tube [1 OJ by turning the steam knob [6] anti-clockwise. Steam and some water will come from the steam wand. Turn off the steam by turning the steam knob into 0 position [6] clockwise.
3.  Immerse the steam tube [11] into the cup with cold milk and turn the steam knob [6] anti­clockwise.
4.  To end the milk frothing process turn the steam knob [6] into O position (clockwise). Take out the steam tube [11] from the cup with milk. Never take the steam tube out of the cup if the steam knob is not turned off to position 0. Hot steam may cause injuries and scalds.
5.  After milk frothing it is advised to put the steam tube [11] into a cup with clean cold water and rinse the system. After the steam tube is immersed in the cup with water turn the steam knob [6] anti-clockwise. After few seconds, turn off the steam flow by turning steam [6] knob clockwise.
6.  Turn off the milk frothing mode by press the”steam switch”[3].

Cleaning and maintenance

Rinse the coffee maker’s water system

1.  Turn device on by pressing the On/Off switch [1 ]. Coffee maker will start to pre-heat, LED will blink.
2.  When coffee maker is ready, the LED will stop to blinking and flash constanley.
3.  Place the filter holder [16 ] in the mounting point [12 ].To rinse the water system of coffee maker. Press the button “coffee switch” [2] and wait for a few seconds, then press “coffee switch” again to close flow of the water.

Regular cleaning after each use Make sure that coffee maker has cooled down.

1.  Remove the filter holder [16] by turning it left (clockwise). Remove the used coffee from filter [14] andclean it with water.
2.  Take thecup cushion and the drip tray out [4 and 5]. Both elements should be cleaned with water and a little bit of dishwashing liquid.
3.  Never immerse the device in water. The housing should be cleaned with a damp cloth, then a dried with a dry cloth to remove moisture.

Regular descaling of coffee maker’s water system

Depending on the hardness of the water descaling process must be performed every 2-3 months. Regular descaling of the machine protects the device and positively affects the taste and aroma of the beverage. WARNING: Lack of descaling causes a significant drop in performance and can lead to damage of the device. Failure to descale the coffee maker will void the warranty. Before descaling process, make sure that the device is disconnected from the power source.

1.  Fill the water tank with about 500 ml of water, and then add 250 ml of descaling liquid for espresso machines (For a correct ratio refer to the manufacturers guide on the preparation of descaling).
2.  Place the filter holder into the filter holding mounting point. Place a cup with a little bit of cold water under the steam tube and place an empty cup under the filter holder outlets.
3.  Connect the device to a power source.
4.  150ml of water flows, turn off the water flow by pressing the coffee switch. Turn the steam knob anti-clockwise for few seconds, and close the hot water flow from the steam tube by turning the steam knob clockwise.
5.  Wait for about 8 minutes, and repeat the procedure until you empty the water in the water tank. After descaling the coffee maker, rinse the water tank thoroughly. Then rinse the coffee maker with clean water twice. Fill the tank full of clean water and repeat steps 2 through 4.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>