GLP impression X4 XL Long Distance Moving LED Stage Light Instruction Manual

GLP impression X4 XL Long Distance Moving LED Stage Light Instruction Manual

Description of Device

1. Moving head (actively and passively cooled)

2. Arm with various cooling vents

3. LCD-Display/Menu (data entry)

4. Base with various connectors and Camlock mounting system
   

5. DMX- Output (5 pin)

6. DMX- Output (3 pin)

7. Micro-fuse: 5 x 20mm, T12A

8. Power Switch
   

9. Neutrik Powercon (Mains power input)

10. Blank panel (primed for Ethernet)

11. DMX- Input (3 pin)

12. DMX- Input (5 pin)

13. 2x Safety wire points
    
    Note: Only connect one cable to the
    DMX Input / Output at the same time

Safety Instructions

The IMPRESSION X4 XL is a High-Tech Product. To guarantee a smooth operation, it is necessary to respect the following rules. The manufacturer of this device will not take responsibility for damages through any disregard of the information provided in this manual. Warranty claims also will be voided in the case that the fixture housing is opened.

Never look directly into the beam of light or into one of the LEDs. Attention: LED Class 2M can cause injuries of your eyes even without optical instruments in front of them or within a distance of less than 0.5m and short exposure time.
Hence: Avoid direct radiation into your eyes!
**WARNING :
Never let optical parts come in contact with alcohol, solvents or similar cleaners.**

1. Before powering on the fixture, make sure that the fixtures fans and air inlets are clean and not blocked.
2. Ensure that the fixture head can rotate unhindered throughout its complete range of pan and tilt movement. A safety distance of at least 0.5 m must be maintained between the fixture and any easily inflammable material.
3. Attention! Don’t touch the fixture during the operation. This can cause injuries and/or damages.
4. The fixture doesn’t contain any user serviceable parts. Opening the fixture will void all warranties.
5. It is necessary to wait at least 15 minutes after disconnecting the mains power before handling the fixture. Pay attention to possible hot parts.
6. To ensure safe operation, follow also the Installation guide described in the chapter below. Operating the IMPRESSION X4 XL without suitable safety aids like Safety cables or clamps/hooks can increase the risk of an accident and must be avoided.
7. Repair, maintenance, and installation work shall be done by qualified or GLP certified staff only. You need to pay attention to the common rules of technology that are not explicitly mentioned in this manual.
8. Use only original GLP spare parts. Any structural modification of the system will terminate all warranty claims.
9. Please keep this instruction manual for future reference.

Important Safety Information

The IMPRESSION X4XL fixture from GLP is fitted with a number of planoconvex lenses in a highly efficient collimator cluster. This type of lens can act as a strong magnifying glass.

If the rays from a strong light source (such as the sun or another lighting fixture) are directed towards the front of any of these fixtures, then internal damae may occur. In a worst case scenario with a high power light source this can happen very quickly, damaging the fixture internally, potentially melting components or causing an internal fire within seconds.

In order to avoid these possible problems please adhere to the following
requirements:

• Do not expose the front of a fixture to direct sunlight or any other strong light sources.
• For outdoor applications during daylight make sure that the front face of any fixture is either shielded or points away from the sun, even when fixtures are not in use.
• Do not modify the front glass or lenses of any fixture.

These requirements have to be followed regardless of whether a fixture is powered on or off as the magnifying effect is an optical effect and therefore independent from the (electrical) state of the fixture.

Especially when working with high powered beam-lights; extreme caution and observance of these safety instructions is mandatory.

Should you have any questions about the operation of your fixture then please contact your local GLP office, or their authorized distributor, a list of which can be found at www.glp.de.

Mounting

The IMPRESSION X4XL is fully operational whether it hangs or is mounted to the wall. It can also be operated while standing on the floor. Keep a safety distance of min. 0.5 m towards any easily inflammable materials (decoration etc.).

Pay attention to the regulations of: BGV C1 (former VBG 70) and DIN VDE 0711-217.
The installation shall be done by qualified staff only.

For the various mounting positions of the IMPRESSION X4XL (standing on the floor, sideways or hanging) different accessories kits are available. Through this a safe and firm installation is assured. You’ll find dedicated connectors on the bottom side of the fixture which should be used. In addition the base is marked with a FRONT arrow allowing consistent orientation during installation.

1. Mounting on the Floor (upright)
   To operate the IMPRESSION X4XL in an upright position, please use the dedicated tri-legged floor stand supplied with your fixture. It is fixed to the base of the fixture with fasteners called Camlock quick-release connectors. Insert the two fasteners and turn each 90° to lock them. Do the opposite to release them again. On both sides you’ll find eyelets to pull though a fixing strap. This allows for additional bracing of the fixture.
   

2. Mounting in hanging position (Head down)
   To operate the IMPRESSION X4XL in a hanging position two (2) omega brackets can be mounted directly to the bottom of the base using the four (4) Camlock connectors.
   Alternatively two half-couplers (clamps) can be mounted directly to the bottom side of the fixture using M10x16 mm thread bolts.
   Attention: Never use a longer bolt as this may damage the interior of the fixture.
   

3. Securing the Fixture
   Regardless of the mounting method of the IMPRESSION X4XL you’ll have to use a stipulated safety wire. Attach the safety wire through one of the two holes provided on the base of the fixture and connect it to the primary support structure. Pay attention to a safe and proper fastening. The safety cable must comply with EN 60598-2-17 Section 17.6.6 and be capable of bearing a static suspended load that is ten times the weight of the fixture and all installed accessories.

4. Connections

5. Power Supply
   ~100-240 Volt AC, 50-60 Hz, earth contact type plug – Powercon Connected load 1200 VA (W) <=> T12A (micro-fuse 5x20mm)
   Please see printing on the case for the right electronic supply!
   Disconnect from the mains supply for changing the fuse and use only the above described micro-fuse type.

6. DMX
   USITT DMX-512 Standard input/output in 3/5 pin connectors.
   Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] / Pin 4&5 N.C.
   The DMX- Addressing starts at the DMX- Address [001].

The Menu Field

You’ll find the control board on the side part of the arm. It allows you to make all necessary adjustments of the IMPRESSION X4XL. With the Mode-key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys. Push the Enter-key to get in the next menu level or to confirm your settings. Make them and set functions ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key (the display shows OK). Push the Mode- key to cancel the entry and go back to the main menu.

To lock or unlock the keys of the menu field press Mode+Enter+Up simultaneously.
 MODE – ENTER
DOWN – UP

Manual control for red
| Color Wheel| Manual control for the color wheel
| Tilt| Manual control for Tilt (Y-movement)
| Adjust| |
| | Key code xxxx| Use the code for entering the calibration menu (for authorized persons only)
| Display Contrast| Adjustment for the Display contrast
| PWM –| Changes PMW frequency
Frequ. Adj.
| Pan Offset| Calibration for Pan-Offset
| Tilt Offset| Calibration for Tilt-Offset
| LED adjust| |
| | White adjust red| Adjust intensity for red channel
| White adjust blue| Adjust intensity for blue channel
| White adjust green| Adjust intensity for green channel
| | Clear EEPROM| | Erase EEPROM memory
| Diagnose| Diagnose fixture functions
| DMX Image| |
| | Set image if DMX off| Activates a stored scene if DMX is off
| Save image in memory| Stores the scene currently sent to the unit
| DMX input Monitor| | Indicates the presently received DMX signal per DMX channel
| | Pan| Instantaneous value for Pan
| Tilt| Instantaneous value for Tilt
| Pattern Byte 3| Instantaneous value for Pattern Byte 3
| Pattern Byte 2| Instantaneous value for Pattern Byte 2
| Pattern Byte 1| Instantaneous value for Pattern Byte 1
| | Pattern| | Instantaneous value for Pattern channel / bank
| | Zoom| | Instantaneous value for Zoom
| | Speed Movements| | Speed adjustment for Pan/Tilt movements à
| | Pan/Tilt Movements| | see item below
| | Special| | Instantaneous value for Pan/Tilt movements
| | White Temperature| | Instantaneous value for Special
| | Dimmer| | Adjustment of the color temperature for WHITE
| | Shutter| | Instantaneous value for Dimmer
| | White| | Instantaneous value for Shutter
| | Blue| | Instantaneous value for White
| | Green| | Instantaneous value for Blue
| | Red| | Instantaneous value for Green
| | Color Wheel| | Instantaneous value for Red
Set DMX Mode| | | | Instantaneous value for Color Mixing unit
| | | | Select the desired DMX Mode
| Compressed Mode| | | Fixture works in “Compressed” mode à see also section 5 below
| Normal Mode| | | Fixture works in “Normal” mode à see also section 5 below
| High-Res.Mode| | | Fixture works in “High Resolution” mode à see also section 5 below
Position feedback| | | | Switch automatic position feedback ON/OFF
Reverse Pan| | | | Invert Pan movements: ON/OFF
Reverse Tilt| | | | Invert Tilt movements: ON/OFF
Reset| | | | RESET and new calibration for all functions

DMX Channel Selection (DMX Protocol)

1. Normal-Mode (26 DMX channels)
   Channel| Function| Time and Value| DMX| HEX| %
   ---|---|---|---|---|---
   1) PAN High| Pan coarse| 0° – 643°| 0..255| 00..FF| 0..100
   2) PAN Low| Pan fine| | 0..255| 00..FF| 0..100
   3) Tilt High| Tilt coarse| 0° – 295°| 0..255| 00..FF| 0..100
   4) Tilt Low| Tilt fine| | 0..255| 00..FF| 0..100
   5) Color (fixed)| Colors adjustable via RGB| | 0..7| 00..07| 0..2..5
   Color 01 – Red 1)| | 8..15| 08..0F| 3..5.5
   Color 02 – Amber 1)| | 16..23| 10..17| 6..8.5
   Color 03 – Warm Yellow 1)| | 24..31| 18..1F| 9..12.5
   Color 04 – Yellow 1)| | 32..39| 20..27| 13..15.5
   Color 05 – Green 1)| | 40..47| 28..2F| 16..18.5
   Color 06 – Turquoise 1)| | 48..55| 30..37| 19..21.5
   Color 07 – Cyan 1)| | 56..63| 38..3F| 22..24.5
   Color 08 – Blue 1)| | 64..71| 40..47| 25..27.5
   Color 09 – Lavender 1)| | 72..79| 48..4F| 28..30.5
   Color 10 – Malve 1)| | 80..87| 50..57| 31..34.5
   Color 11 – Magenta 1)| | 88..95| 58..5F| 35..37.5
   Color 12 – Pink 1)| | 96..103| 60..67| 38..40.5
   White – CTO| 3200K| 104..111| 68..6F| 41..43.5
   White| 5600K| 112..119| 70..77| 44..46.5
   White – CTB| 7200K| 120..127| 78..7F| 47..49.5
   Rainbow Effect Stop 2)| | 128| 80| 50
   Rainbow Effect 3)| slow – fast| 129..223| 81..DF| 51..88
   Random colors| slow – fast| 224..255| E0..FF| 89..100
   6) Red| Color mixing system – Red| 0 – 100%| 0..255| 00..FF| 0..100
   7) Green| Color mixing system – Green| 0 – 100%| 0..255| 00..FF| 0..100
   8) Blue| Color mixing system – Blue| 0 – 100%| 0..255| 00..FF| 0..100
   9) White| Color mixing system – White| 0 – 100%| 0..255| 00..FF| 0..100
   10) Shutter| Shutter closed| | 0..15| 00..0F| 0..5.5
   Shutter pulse random| slow – fast| 16..47| 10..2F| 6..18.5
   Fade on, snap off (random patterns)| slow – fast| 48..79| 30..4F| 19..31
   Snap on, fade off (random patterns)| slow – fast| 80..111| 50..6F| 32..43
   Fade on, fade off (random patterns)| slow – fast| 112..143| 70..8F| 44..56
   Strobe random| 5s – 0.1s| 144..199| 90..C7| 57..77
   Strobe effect slow – fast| 1 Hz – 10 Hz| 200..239| C8..EF| 78..94
   Shutter open| | 240..255| F0..FF| 95..100
   11) Dimmer| Intensity| 0 – 100%| 0..255| 0..FF| 0..100
   12) CTO| No CTO| | 0..7| 0..07| 0..2.5
   Continuous color temperature

correction

| Applicable for ALL

colors

| 8..255| 08..FF| 3..100
13) Special| Pattern Block 1 à See channel 17| | 0..3| 00..03| 0..1
Pattern Block 2 à See channel 17| | 4..7| 04..07| 2..3
Pattern Block 3 à See channel 17| | 8..11| 08..0B| 3..4
Pattern Block 4 à See channel 17| | 12..15| 0C..0F| 5..6
Pattern Block 5 à See channel 17| | 16..19| 10..13| 6..7
Pattern Block 6 à See channel 17| | 20..23| 14..17| 8..9
Pattern Block 7 à See channel 17| | 24..27| 18..1B| 9..10
Pattern Block 8 à See channel 17| | 28..31| 1C..1F| 11..12
Pattern Block 9 à See channel 17| | 32..35| 20..23| 12..13
Pattern Block 10 à See channel 17| | 36..39| 24..27| 14..15
Channel| Function| Time and Value| DMX| HEX| %|
| Enable Animation| 80..83| 50..53| 31..32|
à use channel 17 to select

à use channel 18 so set step

à use channel 19 to start / for speed

|
Set Dimmer to soft mode| | 84..87| 54..57| 33..34|
Change PWM frequency| | 100..200| 64..C8| 40..78|
Set Maximum Zoom to 247| > 1 sec| 208..211| D0..D3| 82..83|
Set Maximum Zoom to 255| > 1 sec| 212..215| D4..D7| 84..85|
Set Zoom to normal| > 1 sec| 216..219| D8..DB| 85..86|
Set Zoom to inverted| > 1 sec| 220..223| DC..DF| 86..87|
RESET| > 1 sec| 250..255| FA..FF| 98..100|
14) Move-

ment macros

| No macros| | 0| 00| 0|
Movement| Size| Phase| Use “Speed” to adjust| | | |
PAN| 1| 0°| | 01..01| 01..01| 0.5|
| 1| 90°| | 02..03| 02..03| 1.0|
| 1| 180°| | 04..05| 04..05| 1.7|
| 1| 270°| | 06..07| 06..07| 2.5|
PAN| 2| 0°| | 08..09| 08..09| 3.3|
| 2| 90°| | 10..11| 0A..0B| 4.1|
| 2| 180°| | 12..13| 0C..0D| 4.9|
| 2| 270°| | 14..15| 0E..0F| 5.7|
PAN| 3| 0°| | 16..17| 11..11| 6.5|
| 3| 90°| | 18..19| 12..13| 7.3|
| 3| 180°| | 20..21| 14..15| 8.0|
| 3| 270°| | 22..23| 16..17| 8.8|
PAN| 4| 0°| | 24..25| 18..19| 9.6|
| 4| 90°| | 26..27| 1A..1B| 10.4|
| 4| 180°| | 28..29| 1C..1D| 11.2|
| 4| 270°| | 30..31| 1E..1F| 12|
TILT| size / phase see PAN| 32..63| 20..3F| 13..25|
PAN / TILT| size / phase see PAN| 64..95| 40..5F| 26..37|
PAN / TILT (inverse)| size / phase see PAN| 96..127| 60..7F| 38..50|
Circle| size / phase see PAN| 128..159| 80..9F| 51..62|
Circle (inverse)| size / phase see PAN| 160..191| A0..BF| 63..75|
Lying eight| size / phase see PAN| 193..223| C0..DF| 76..87|
Random movement| size / phase see PAN| 224..255| E0..FF| 88..100|
15) Pan / Tilt Speed| Pan/Tilt movement speed from controller| | 0..1| 00..01| 0..0..5|
Pan/Tilt, slow – fast

Use this channel for the speed of the macros on channel 14.

| | __

02..255

| __

02..FF

| __

1..100

|
16) Zoom| Wide (flood) – narrow (spot)| 50° – 7°| 0…255| 00…FF| 0…100|
17) Pattern / Animation| No pattern| | 0..2| 00..02| 0..1|
Pre-defined patterns / animations 4) 5)| See Special Channel 13| 03..253| 03..FD| 2..99|
Activates direct access to LED Lenses| See Channel 18 – 26| 254..255| FE..FF| 100|
18) Pattern Section 1 4)| Direct activation of lenses 1 thru 8 4)| Activation in binary style| 0…255| 00…FF| 0…100|
19) Pattern Section 2 5)| Direct activation of lenses 9 thru 16 5)| Activation in binary style| 0…255| 00…FF| 0…100|
20) Pattern Section 3| Direct activation of lenses 17 thru 19| Activation in binary style| 0…255| 00…FF| 0…100|
21) Pattern Section 4| Direct activation of lenses 20 thru 27| Activation in binary style| 0…255| 00…FF| 0…100|
Channel| Function| Time and Value| DMX| HEX| %|
22) Pattern Section 5| Direct activation of lenses 28 thru 35| Activation in binary style| 0…255| 00…FF| 0…100|
23) Pattern Section 6| Direct activation of lenses 36 thru 38| Activation in binary style| 0…255| 00…FF| 0…100|
24) Pattern Section 7| Direct activation of lenses 39 thru 46| Activation in binary style| 0…255| 00…FF| 0…100|
25) Pattern Section 8| Direct activation of lenses 47 thru 54| Activation in binary style| 0…255| 00…FF| 0…100|
26) Pattern Section 9| Direct activation of lens 55| Activation in binary style| 0…255| 00…FF| 0…100|
2. Compress-Mode (16 DMX channels)
Channel| Function| Time and Value| DMX| HEX| %
---|---|---|---|---|---
1) PAN High| Pan coarse| 0° – 643°| 0..255| 00..FF| 0..100
2) PAN Low| Pan fine| | 0..255| 00..FF| 0..100
3) Tilt High| Tilt coarse| 0° – 295°| 0..255| 00..FF| 0..100
4) Tilt Low| Tilt fine| | 0..255| 00..FF| 0..100
5) Color (fixed)| Colors adjustable via RGB| | 0..7| 00..07| 0..2.5
Color 01 – Red 1)| | 8..15| 08..0F| 3..5.5
Color 02 – Amber 1)| | 16..23| 10..17| 6..8.5
Color 03 – Warm Yellow 1)| | 24..31| 18..1F| 9..12.5
Color 04 – Yellow 1)| | 32..39| 20..27| 13..15.5
Color 05 – Green 1)| | 40..47| 28..2F| 16..18.5
Color 06 – Turquoise 1)| | 48..55| 30..37| 19..21.5
Color 07 – Cyan 1)| | 56..63| 38..3F| 22..24.5
Color 08 – Blue 1)| | 64..71| 40..47| 25..27.5
Color 09 – Lavender 1)| | 72..79| 48..4F| 28..30.5
Color 10 – Mauve 1)| | 80..87| 50..57| 31..34.5
Color 11 – Magenta 1)| | 88..95| 58..5F| 35..37.5
Color 12 – Pink 1)| | 96..103| 60..67| 38..40.5
White – CTO| Color temperature

3200K

| 104..111| 68..6F| 41..43.5
White| Color temperature

5600K

| 112..119| 70..77| 44..46.5
White – CTB| Color temperature

7200K

| 120..127| 78..7F| 47..49.5
Rainbow Effect Stop 2)| | 128| 80| 50
Rainbow Effect 3)| slow – fast| 129..223| 81..DF| 51..88
Rainbow Effect, random colors| slow – fast| 224.255| E0..FF| 89..100
6) Red| Color mixing system – Red| 0 – 100%| 0..255| 00..FF| 0..100
7) Green| Color mixing system – Green| 0 – 100%| 0..255| 00..FF| 0..100
8) Blue| Color mixing system – Blue| 0 – 100%| 0..255| 00..FF| 0..100
9) White| Color mixing system – White| 0 – 100%| 0..255| 00..FF| 0..100
10) Shutter| Shutter closed| | 0..15| 00..0F| 0..5.5
Shutter pulse random| slow – fast| 16..47| 10..2F| 6..18.5
Fade on, snap off (random patterns)| slow – fast| 48..79| 30..4F| 19..31
Snap on, fade off (random patterns)| slow – fast| 80..111| 50..6F| 32..43
Fade on, fade off (random patterns)| slow – fast| 112..143| 70..8F| 44..56
Strobe random| 5s – 0.1s| 144..199| 90..C7| 57..77
Strobe effect slow – fast| 1 Hz – 10 Hz| 200..239| C8..EF| 78..94
Shutter open| | 240..255| F0..FF| 95..100
11) Dimmer| Intensity| 0 – 100%| 0..255| 0..FF| 0..100
12) Zoom| Wide (flood) – narrow (spot)| 50° – 7°| 0…255| 00…FF| 0…100
13) Special| Pattern Block 1 à See channel 14| | 0..3| 00..03| 0..1
Pattern Block 2 à See channel 14| | 4..7| 04..07| 2..3
Pattern Block 3 à See channel 14| | 8..11| 08..0B| 3..4
Pattern Block 4 à See channel 14| | 12..15| 0C..0F| 5..6
Pattern Block 5 à See channel 14| | 16..19| 10..13| 6..7
Pattern Block 6 à See channel 14| | 20..23| 14..17| 8..9
Pattern Block 7 à See channel 14| | 24..27| 18..1B| 9..10
Pattern Block 8 à See channel 14| | 28..31| 1C..1F| 11..12
Pattern Block 9 à See channel 14| | 32..35| 20..23| 12..13
Pattern Block 10 à See channel 14| | 36..39| 24..27| 14..15
Channel| Function| Time and Value| DMX| HEX| %
| Enable Animation| | 80..83| 50..53| 31..32
à use channel 14 to select

à use channel 15 so set step

à use channel 16 to start / for speed

Set Dimmer to soft mode| | 84..87| 54..57| 33..34
Change PWM frequency| | 100..200| 64..C8| 40..78
Set Maximum Zoom to 247| > 1 sec| 208..211| D0..D3| 82..83
Set Maximum Zoom to 255| > 1 sec| 212..215| D4..D7| 84..85
Set Zoom to normal| > 1 sec| 216..219| D8..DB| 85..86
Set Zoom to inverted| > 1 sec| 220..223| DC..DF| 86..87
RESET| > 1 sec| 250..255| FA..FF| 98..100
14) Pattern / Animation| No pattern| | 0..2| 00..02| 0..1
Pre-defined patterns / animations 4) 5)| See Special Channel 13| 03..253| 03..FD| 2..99
15) A-Step 4)| Animation step 4)| See Special Channel 13| 00..255| 00..FF| 0..100
16) A-Speed 5)| Animation start / speed 5)| See Special Channel 13| 00..255| 00..FF| 0..100
3. High Resolution/Extended-Mode (27 DMX Channels)
Channel| Function| Time and Value| DMX| HEX| %
---|---|---|---|---|---
1) PAN High| Pan coarse| 0° – 643°| 0..255| 00..FF| 0..100
2) PAN Low| Pan fine| | 0..255| 00..FF| 0..100
3) Tilt High| Tilt coarse| 0° – 295°| 0..255| 00..FF| 0..100
4) Tilt Low| Tilt fine| | 0..255| 00..FF| 0..100
5) Red High| Color mixing system – Red| 0 – 100%| 0..255| 00..FF| 0..100
6) Red Low| Color mixing system – Red-Low| | 0..255| 00..FF| 0..100
7) Green High| Color mixing system – Green| 0 – 100%| 0..255| 00..FF| 0..100
8) Green Low| Color mixing system – Green-Low| | 0..255| 00..FF| 0..100
9) Blue High| Color mixing system – Blue| 0 – 100%| 0..255| 00..FF| 0..100
10) Blue Low| Color mixing system – Blue-Low| | 0..255| 00..FF| 0..100
11) White High| Color mixing system – White| 0 – 100%| 0..255| 00..FF| 0..100
12) White Low| Color mixing system – White-Low| | 0..255| 00..FF| 0..100
13) Shutter| Shutter closed| | 0..15| 00..0F| 0..5.5
Shutter pulse random| slow – fast| 16..47| 10..2F| 6..18.5
Fade on, snap off (random patterns)| slow – fast| 48..79| 30..4F| 19..31
Snap on, fade off (random patterns)| slow – fast| 80..111| 50..6F| 32..43
Fade on, fade off (random patterns)| slow – fast| 112..143| 70..8F| 44..56
Strobe random| 5s – 0.1s| 144..199| 90..C7| 57..77
Strobe effect slow – fast| 1 Hz – 10 Hz| 200..239| C8..EF| 78..94
Shutter open| | 240..255| F0..FF| 95..100
14) Dimmer- High| Intensity coarse| 0 – 100%| 0..255| 0..FF| 0..100
15) Dimmer- Low| Intensity fine| | 0..255| 0..FF| 0..100
16) Zoom| Wide (flood) – narrow (spot)| 50° – 7°| 0…255| 00…FF| 0…100
17) Special| Pattern Block 1 à See channel 18| | 0..3| 00..03| 0..1
Pattern Block 2 à See channel 18| | 4..7| 04..07| 2..3
Pattern Block 3 à See channel 18| | 8..11| 08..0B| 3..4
Pattern Block 4 à See channel 18| | 12..15| 0C..0F| 5..6
Pattern Block 5 à See channel 18| | 16..19| 10..13| 6..7
Pattern Block 6 à See channel 18| | 20..23| 14..17| 8..9
Pattern Block 7 à See channel 18| | 24..27| 18..1B| 9..10
Pattern Block 8 à See channel 18| | 28..31| 1C..1F| 11..12
Pattern Block 9 à See channel 18| | 32..35| 20..23| 12..13
Pattern Block 10 à See channel 18| | 36..39| 24..27| 14..15
Enable Animation| | 80..83| 50..53| 31..32
à use channel 18 to select

à use channel 19 so set step

à use channel 20 to start/for speed

Set Dimmer to soft mode| | 84..87| 54..57| 33..34
Change PWM frequency| | 100..200| 64..C8| 40..78
Set Maximum Zoom to 247| > 1 sec| 208..211| D0..D3| 82..83
Set Maximum Zoom to 255| > 1 sec| 212..215| D4..D7| 84..85
Set Zoom to normal| > 1 sec| 216..219| D8..DB| 85..86
Set Zoom to inverted| > 1 sec| 220..223| DC..DF| 86..87
RESET| > 1 sec| 250..255| FA..FF| 98..100
18) Pattern| No pattern| | 0..2| 00..02| 0..1
Pre-defined patterns / animations 4) 5)| See Special Channel 17| 03..253| 03..FD| 2..99
Activates direct access to LED

Lenses

| | 254..255| FE..FF| 100
19) Pattern Section 1 4)| Direct activation of lenses 1 thru 8 4)| Activation in binary style| 0…255| 00…FF| 0…100
Channel| Function| Time and Value| DMX| HEX| %
20) Pattern Section 2 5)| Direct activation of lenses 9 thru 16 5)| Activation in binary style| 0…255| 00…FF| 0…100
21) Pattern Section 3| Direct activation of lenses 17 thru 19| Activation in binary style| 0…255| 00…FF| 0…100
22) Pattern Section 4| Direct activation of lenses 20 thru 27| Activation in binary style| 0…255| 00…FF| 0…100
23) Pattern Section 5| Direct activation of lenses 28 thru 35| Activation in binary style| 0…255| 00…FF| 0…100
24) Pattern Section 6| Direct activation of lenses 36 thru 38| Activation in binary style| 0…255| 00…FF| 0…100
25) Pattern Section 7| Direct activation of lenses 39 thru 46| Activation in binary style| 0…255| 00…FF| 0…100
26) Pattern Section 8| Direct activation of lenses 47 thru 54| Activation in binary style| 0…255| 00…FF| 0…100
27) Pattern Section 9| Direct activation of lens 55| Activation in binary style| 0…255| 00…FF| 0…100

1. The predefined colors can be used as start-colors for the Rainbow effect. Please select first a desired start-color before you activate the rainbow effect. All IMPRESSION X4XL will then start from that color and will execute the rainbow effect synchronously. Different IMPRESSION X4XL can have different start-colors but will still execute the rainbow effect synchronously. If you choose a color different from the ones marked with 1) in the tables above the rainbow start-color will be red.
2. Rainbow-effect Stop will pause this function. After resuming the rainbow-effect will be continued from the current color.
3. The Rainbow-effect will run synchronously only if started from one of the predefined colors (see also 1) before).
4. If the Animation mode is activated through Special Channel set to DMX = 80..83 then the Function of this Channel is:
   Animation step| | 00..255| 00..FF| 0..100
   ---|---|---|---|---

Use this Chanel to select the starting point of the animation.

5. If the Animation mode is activated through Special Channel set to DMX = 80..83 then the Function of this Channel is:  

Locking and unlocking the Control Panel
Please lock and unlock the control panel by pressing the menu keys MODE & ENTER & UP at the
same time.

Additional Display Indications
As a default you’ll find the following additional information in the first row of the LCD display:
Vxx/xx/xx/xx/x

N = Normal Mode / C = Compressed Mode / H = High Res. Mode
N = Tilt normal / I = Tilt inverted
N = Pan normal / I = Pan inverted
LED driver version
Main CPU version

Maintaining and Cleaning

The IMPRESSION X4XL is a fixture of very low maintenance. It is only necessary to clean the air inlets and outlets as well as the optical LED lenses from time to time. For safe operation it is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on, or within the fixture. Otherwise the fixture’s light-output will be significantly reduced or damages can occur. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to operate reliably throughout its life.
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended to clean the lenses.

Attention:
Under no circumstances should alcohol or solvents be used to clean the lenses!

1. Safety regulations
   • Pull out the mains power plug!
   • Wait min. 15 minutes after disconnecting power to allow the fixture to cool down.
2. Maintenance and Interval (rule-of-thumb)
   The contamination of the fixture depends on the environment details. Hence no general guidelines can be given. The intervals given below are only suggestions from our experience. Position| Interval| In this way
   ---|---|---
   LED reflector and optical system| weekly| soft brush /lint-free cloth
   Fan and air channel| monthly| vacuum cleaner, airbrush, etc.

Attention:

• Never let optical parts come into contact with oil, fat, alcohol or similar solvents.
• Before running the fixture wait until all parts are dry.
• Never touch lenses with bare fingers.

Technical Specifications

Power supply

Power consumption| 1200 VA (Watt)
Power Input| ~100-240 V AC, 50-60 Hz (wide range input)
Fuse protection| Micro-fuse 5×20 mm, T12A
Operational Parameters
Max. Ambient Temperature| 5° – 45°C (integrated overheating switch)
Mounting Position| Any (see relevant chapter)
Lighting System – Additive Color mixing
LED Type| 55 x Osram Ostar RGBW multi-chip
Lifetime| 50,000 h
Wavelength optimized for maximum presentable color space
Optical System
Full RGBW / High efficient Collimator cluster
Shutter / Dimmer (8/16 Bit)
Strobe- Effect with variable speed between 1 – 10 flashes per second, Random- Strobe, Pulse- Effects
Continuous Dimmer 0 – 100%
Zoom
7 to 50 degree continuous zoom
Optical Patterns
Several hundred pre-defined beam patterns with direct access and manipulation
DMX Control
Standard USITT DMX-512, 3/5 pin XLR: [+]=Pin 3 / [-]=Pin 2 / [Ground]=Pin 1 / Pin 4&5 N.C. The DMX- Addressing starts at the DMX channel [001].
Pan / Tilt (8/16 Bit)
Pan- movement| 643° in min. 3,2 seconds (Position Feedback)
Tilt- movement| 295° in min. 1,5 seconds (Position Feedback)
Weights and Measures
Width of the base| 521 mm
Length of the base| 361 mm
height (head vertical)| 519 mm (incl. standing foot/tripod)
Weight (net)| 31.0 kg

Dimensions

Tilt range: 295°

Pan range: 643°

References

• GLP German Light Products - Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>