GLP Impression Frio Bar Instruction Manual
- June 7, 2024
- GLP
Table of Contents
Impression Frio Bar
Quick Start and Safety Manual
Software version V. 20
GLP® FR10 Bar Quick Start and Safety Manual Revision A
This manual covers fixture software version V. 20
© 2019 German Light Products GmbH. All rights reserved.
The marks GLP’ andGerman Light Products’ are trademarks registered as the
property of German Light Products GmbH in Germany, in the United States of
America and in other countries.
The information contained in this document is subject to change without
notice. German Light Products GmbH and all affiliated companies disclaim
liability for any injury, damage, direct or indirect loss, consequential or
economic loss or any other loss occasioned by the use of, inability to use or
reliance on the information contained in this document.
Manufacturer head office: German Light Products GmbH (GLP), Industriestrasse
2, 76307 Karlsbad, Germany Tel (Germany): +49 7248 92719 – 0
Service & Support EMEA: GLP, Industriestrasse 2, 76307 Karlsbad, Germany Tel.
(Germany): +49 7248 9271955 Email: support@glp.de www.glp.de
Service & Support USA: GLP USA, 1145 Arroyo St., Ste. A, 91340 San Fernando,
California Tel (USA): +1 818 767 8899 Support (US):
info@germanlightproducts.com www.germanlightproducts.com
Table of Contents
1. Safety ……………………………………………………………………………………. 4 Key to symbols
…………………………………………………………………… 4 General safety information ………………………………………………… 4
Electrical safety …………………………………………………………………. 5 Fire safety and protection from
burns…………………………………. 6 Eye safety ………………………………………………………………………….. 7 Strobe
safety……………………………………………………………………… 7 Installation safety and protection from
personal injury ……….. 8
2. Avoiding damage to the fixture …………………………………………….. 9 General precautions
…………………………………………………………. 9 Avoiding damage from light sources and heat
………………….. 9 Avoiding damage from dust and airborne particles…………. 10
Transportation and storage ……………………………………………… 10
3. FR 10 Bar overview ……………………………………………………………….. 11
4. Features ………………………………………………………………………………. 12 User Manual
…………………………………………………………………….. 12 Tilt lock …………………………………………………………………………….. 12
5. Installation……………………………………………………………………………. 13 Mounting options
…………………………………………………………….. 13 Securing the fixture with a safety cable
……………………………. 13 End-to-end alignment ……………………………………………………… 14 Standing an FR
10 Bar on a horizontal surface ………………….. 14 Installing on a rigging truss or
similar structure …………………… 15
6. AC mains power ………………………………………………………………….. 16 Power cable
……………………………………………………………………. 16 Connecting to power ………………………………………………………. 16
Installing power connectors……………………………………………… 17 Connecting multiple fixtures
to power in a chain ……………… 17
7. Connecting to DMX data …………………………………………………….. 18
8. Starting and stopping operation…………………………………………… 19 Transportation and
storage ……………………………………………… 19
9. Service ………………………………………………………………………………… 20 Removing the front glass
………………………………………………….. 20 Cleaning …………………………………………………………………………. 20 GLP Service
and Support …………………………………………………. 21
10. Technical specifications …………………………………………………….. 22
11. Dimensions ………………………………………………………………………… 24
www.glp.de
1. Safety
Key to symbols
The following symbols are used in this Guide:
Warning! Safety hazard. Risk of severe injury or death.
Warning! See user manual for important safety information.
Warning! Risk of eye injury.
Warning! Hazardous voltage. Risk of lethal or severe electric shock.
Warning! Fire hazard.
General safety information
Read this manual carefully before installing, using or servicing the GLP
impression FR 10 Bar lighting fixture.
If you have any doubts or questions about how to use the fixture safely,
contact your GLP® supplier for assistance. Your GLP supplier will be happy to
help.
The user documentation for FR 10 Bar lighting fixtures consists of:
· The FR 10 Bar Quick Start and Safety Manual, supplied with FR 10 Bar
fixtures and available for download from www.glp.de. The Quick Start and
Safety Manual contains important safety information and installation
instructions that the installer and user must read.
· The FR 10 Bar User Manual, available for download from www.glp.de. The User
Manual explains features and control of FR 10 Bar fixtures.
· The FR 10 Bar DMX Channel Index, available for download from www.glp.de. The
Channel Index is a separate guide to the DMX control channel layout and DMX
commands available.
All documents are available for download from www.glp.de.
The impression FR 10 Bar is intended for use by experienced professionals with
the knowledge and skills to set up, operate, and maintain high-powered,
remotely controlled lighting equipment safely and efficiently. These
operations require expertise that may not be provided in this Manual or in the
User Manual.
· Respect all warnings and directions given in the fixture’s user
documentation and on the fixture. Read the user documentation and familiarize
yourself with the safety
4
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
precautions it contains before installing or using the fixture. GLP and
affiliated companies will take no responsibility for damage or injury
resulting from disregard for the information in the user documentation.
· Check the GLP website at www.glp.de and make sure that you have the latest
version of this manual. Check the fixture software version indicated on page 2
of this manual and then use the fixture’s control panel to check the version
installed in the fixture. If the versions are not the same, this manual may
still cover the fixture, because software updates do not always affect the way
you use the fixture. However, it is possible that this manual does not match
the fixture perfectly. Software release notes can help clarify this question.
You can consult software release notes and download the correct version of
this manual on the GLP website if necessary.
· Make all user documentation this Quick Start and Safety Manual as well as
the User Manual available to all installers and operators. Save both
documents for future reference.
· If you have any questions about the safe operation of the fixture, please
contact an authorized GLP distributor (see list of distributors at
www.glp.de).
· Use the fixture only as directed in this manual. Observe all markings in
this manual and on the fixture.
· Refer all repairs and any service operation not described in this manual to
a technician authorized by GLP.
· The light source in this fixture must not be changed by the end user.
· Read and follow the user documentation for all additional equipment.
Electrical safety
· The fixture is for use in dry locations only. Do not allow the fixture to
come into contact with water or moisture.
· Use only a source of AC mains power that complies with local building and
electrical codes and has both overload and ground fault (earth fault)
protection.
· Ensure that the fixture is electrically connected to ground (earth).
· Disconnect the fixture from AC mains power before carrying out any
installation or maintenance work and when the fixture is not in use.
· Disconnect the fixture from power immediately if any seal, cover, cable,
connector or other component is damaged, defective, deformed or showing signs
of overheating. Do not reapply power until the fixture has been repaired and
made safe by a technician authorized by GLP.
· Check that all power distribution equipment, cables and connectors are in
perfect condition, rated for the electrical requirements of all connected
devices, suitable for their application and suitable for the installation
environment.
Impression FR10 Bar Quick Start and Safety Manual Rev. A
5
www.glp.de
· Use only Neutrik PowerCON TRUE1 cable connectors for AC mains power input at
the fixture’s Mains IN connector and for relaying AC mains power from one
fixture’s Mains OUT (Thru) connector to another fixture’s Mains IN connector.
· Use minimum 14 AWG or 1.5 mm2 power input and relay cables that are minimum
16 A-rated and temperature-rated to suit the application. In the USA and
Canada the cables must be UL-listed, type SJT or equivalent. In the EU the
cables must be type H05VV-F or equivalent.
· Do not connect devices to power in a chain if the total maximum current draw
of all the devices in the chain when added together will exceed the current
rating of any cable or connector used at any point in the chain. The supplied
power input cable is rated as follows:
– US power cable: 16 A, 14 AWG, UL-listed, E304117, SJT, 4.9 ft.
– EU power cable: 16 A, 1.5 mm², H05VVF-F, 1.5 m.
Do not connect more than two (2) FR 10 Bar fixtures to power linked together
at 100120 V, 60 Hz.
Do not connect more than four (4) FR 10 Bar fixtures to power linked together
in a chain at 200-240 V, 50 Hz.
· The voltage and frequency at the Mains OUT socket are the same as the
voltage and frequency applied to the Mains IN socket. Only connect devices to
the Mains OUT socket that accept this voltage and frequency.
· Replace the fuse with a new fuse of the same type and rating only.
Fire safety and protection from burns
· Do not operate the fixture if the ambient temperature (Ta) exceeds 45° C
(113° F).
· The surface of the fixture can become hot during operation. Avoid contact by
persons and materials. Do not install the fixture in a location where there is
a risk of accidental contact. Allow the fixture to cool for at least 20
minutes before handling
· Keep the fixture well away from flammable materials.
· Keep all combustible materials (e.g. fabric, wood, paper) at least 0.2 m (8
in.) away from the fixture.
· Ensure that there is free and unobstructed airflow around the fixture.
· Do not illuminate surfaces within 0.2 m / 8 in. of the fixture. The light
output from the fixture is powerful enough to cause burns or fire in
illuminated objects at very close range.
· Do not place any optical components other than impression FR 10 Bar
accessories from GLP onto the front of the fixture.
· Do not stick filters, masks or other materials onto the fixture. Do not
block the light output in any way. The front surface becomes hot during
operation and can melt or ignite objects that are in contact with the surface.
Ensure that the front surface Is
6
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
clean and unobstructed at all times in order to prevent a fire hazard and
damage to the fixture. · The fixture’s optical components can focus the sun’s
rays, creating a risk of fire and damage. Do not expose the front of the
fixture to sunlight or any other intense light source, even from an angle.
Eye safety
· The FR 10 Bar is classified as a Risk Group 2 lighting fixture according to
EN 62471. Possibly hazardous radiation emitted. Do not stare into the light
output from the fixture. May be harmful to the eyes.
· Do not look at the fixture’s light output with optical instruments or any
device that may concentrate the light output.
· Make sure that persons near to or working on the fixture are not looking
directly into the light output when the fixture lights up suddenly. This can
happen when power is applied, when the fixture receives a DMX signal, or when
certain control menu items are selected.
· Provide well-lit conditions to reduce the pupil diameter of anyone working
on or near the fixture.
Strobe safety
· Flashing light, particularly at 5 – 30 Hz, may cause seizures in persons
with photosensitive epilepsy. Do not use strobe effects for extended periods.
· Comply with local regulations on the use of strobe lighting and notify the
public in advance with highly visible warning signs when strobe effects are
used.
· If a seizure occurs, stop using strobe effects. Seek professional medical
help. Note the time that the seizure starts and finishes. Call emergency
medical help urgently if the seizure lasts more than five minutes, if it is
the person’s first seizure, or if the person is injured. While waiting for
help to arrive, protect the affected person from injuring themselves on hard
or sharp objects. If necessary, move the person to a safe place. Lay them on
their side with their head supported to prevent it from hitting the floor.
Loosen any tight clothing around their neck. Do not use force to hold the
person or restrict their movements. Do not put anything in their mouth,
including your fingers.
Impression FR10 Bar Quick Start and Safety Manual Rev. A
7
www.glp.de
Installation safety and protection from personal injury
· Installation must be performed by qualified personnel only and carried out
in accordance with applicable regulations such as DIN VDE 0711-217.
· The fixture is not portable when installed. · Ensure that the supporting
structure and installation hardware used can hold at least
ten times the weight of the load that they support. · Fasten the fixture to a
structure or surface only as directed in this manual and only
with hardware that is specifically designed and rated for its purpose. Do not
use a safety cable as the primary means of support. Check that installation
hardware is in perfect condition. Fasteners must be steel grade 8.8 strength
or better. Rigging clamps must be half-coupler type that completely encircle
the rigging truss chord. · If the fixture is installed in a location where it
may cause injury or damage if it falls, install as directed in this manual a
safety cable or similar secondary attachment that will hold the fixture if a
primary attachment fails. The secondary attachment must be approved by an
official body such as TÜV as a safety attachment for the weight that it
secures, it must comply with EN 60598-2-17 Section 17.6.6, and it must be able
to support a static suspended load that is ten times the weight that it
secures. · If the fixture is installed in a location where it may be exposed
to forces such as wind pressure, vibration or movement, make sure that the
installation can withstand these forces. Monitor weather forecasts constantly.
Take down the installation immediately if there is any risk of weather
conditions that could destabilize the installation. · Check that all covers
and items of rigging hardware are secure before using the fixture. Do not
operate the fixture with missing or damaged covers, shields or any optical
component. · Restrict access below the work area and work from a stable
platform whenever installing, servicing or moving the fixture. · If the
fixture becomes damaged, stop using it immediately and disconnect it from
power. Do not attempt to use a fixture that is obviously damaged. · Do not
modify the fixture in any way not described in its user documentation. ·
Install genuine GLP parts only.
8
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
2. Avoiding damage to the fixture
Important! Follow the directions in this section carefully, or the fixture may
suffer damage that is not covered by the product warranty.
General precautions
Do not drop the fixture or expose it to mechanical stress. Protect the LCD
display and control panel from shocks, or they may suffer damage that is not
covered by the product warranty. Do not expose the fixture to heat (from other
lighting fixtures for example). Clean optical components only as directed.
Oils, solvents, and other chemicals commonly used for cleaning can damage the
lens coatings and surfaces. Use only original spare parts. Do not make any
structural modifications to the fixture or you will void the product warranty.
Create loose cable bends only. Do not subject connectors to bending forces or
allow connectors to bear the weight of long lengths of cable.
Avoiding damage from light sources and heat
Do not point the front of the fixture towards the sun or other strong light
sources. Strong light can cause internal damage to the fixture, melting
components or starting an internal fire within seconds.
Figure 1. Avoiding damage from light sources
Damage can occur whether the fixture is powered on or off. See Figure 1.
Damage can also occur if the light hits the front of the fixture at an angle:
the fixture does not need to be pointing directly at the sun or other light
source. To avoid problems from strong light sources: · Do not expose the front
of the fixture to sunlight or any other strong light source. · In outdoor
applications during daylight, make sure that the front face of the fixture is
shielded or points away from the sun, even when not in use. · Do not aim other
high-powered beam lights directly at the fixture.
Impression FR10 Bar Quick Start and Safety Manual Rev. A
9
www.glp.de
Do not operate the fixture in ambient temperatures above 45° C / 113° F or
below 5° C / 41° F. Allow free airflow around the fixture.
Avoiding damage from dust and airborne particles
· Carry out regular visual inspections of the fixture to make sure that there
is no accumulation of dirt, especially on the front of the fixture and around
air vents.
· If cleaning is necessary, follow the instructions in `Service’ on page 20.
Transportation and storage
· Transport the fixture in its original packaging to protect it from damage
caused by shocks during transportation.
· Release the fixture’s tilt lock before putting the fixture in its flightcase
or other protective container for transportation. Before closing the
flightcase, check that the protective liner in the flightcase will hold the
head and protect it from shocks.
· Store the fixture in a dry location when not in use.
10
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
3. FR 10 Bar overview
A B
D C
E
FG
H
J K I
Figure 2. FR 10 Bar overview
A Head B Pixel zoom lens C Alignment pins button D DMX IN (5-pin XLR) E AC mains power IN (Neutrik powerCON TRUE1) F etherCon Port IN/THRU, fail-safe (Art-Net / sACN) G Fuseholder H Control panel with backlit display I etherCon Port IN/THRU, fail-safe (Art-Net / sACN) J AC mains power THRU (Neutrik powerCON TRUE1) K DMX THRU (5-pin XLR)
Impression FR10 Bar Quick Start and Safety Manual Rev. A
11
www.glp.de
4. Features
The impression FR 10 Bar from GLP can be used in dry locations in permanent
and temporary installations. Fixtures can be placed on or fastened to a level
surface, or they can be suspended from a suitable structure as directed in
this manual.
Power and data can be daisy-chained for ease of installation, and multiple
fixtures can be lined up to give an unbroken line of pixels using the
retractable alignment pins that are built into the fixture.
The FR 10 Bar is not suitable for household use, for use in any location where
unattended children have access to it, or for use in locations that may be
exposed to water or humidity.
User Manual
This Quick Start and Installation Manual gives a very basic overview of
control options and functions. See the FR 10 Bar User Manual available for
download from www.glp.de for full details of control, pixel layout, etc.
Tilt lock
Important! Before transporting the FR10 Bar, release the tilt lock and make sure that the head is supported to prevent it from moving.
The FR10 Bar has a tilt lock that can be used to prevent the head from moving while the fixture is being carried. The tilt lock also lets you immobilize the head during cleaning or while installing optical accessories on the front of the fixture.
See Figure 3. The tilt lock button is located on the back of the head, at the left-hand end of the head when viewing the fixture from the control panel side. To engage the tilt lock:
Check that power to the fixture is shut down.
Move the head into the upright position, facing away from the fixture base.
Slide the tilt lock button towards the yoke and into the Lock position to
engage it.
Figure 3. Tilt lock button
Release the tilt lock by sliding it away from the yoke and into the Unlock position before reapplying power to the fixture.
12
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
5. Installation
Warning! Read `Safety’ starting on page 4 for important safety information
that you must understand before you install or operate the fixture. Install FR
10 Bar fixtures only as described in this chapter, or you may create an
installation that is unsafe. It is the installer’s responsibility to provide a
stable, secure supporting structure that is suitable for the environment and
application and that meets all applicable codes and legal requirements. Note
the requirement to secure lighting fixtures with safety cables in temporary
installations.
Mounting options
An FR 10 Bar fixture may be installed in one of the following ways:
Standing horizontally on a horizontal surface.
Fastened to a rigging truss or similar structure at any angle using the
supplied brackets and two or more rigging clamps (optional accessories).
Securing the fixture with a safety cable
If a fixture can cause injury or damage if it falls you must secure it with at
least one secondary attachment such as a safety cable that will hold it if the
primary means of attachment fails. The safety cable must be approved for the
weight that it secures. In multiple installations, each fixture must have its
own safety cable.
Figure 4. Safety cable attachment points
To secure an FR 10 Bar fixture with a safety cable: Obtain a safety cable that
is approved for the weight of the fixture and rigging hardware that it will
secure.
Impression FR10 Bar Quick Start and Safety Manual Rev. A
13
www.glp.de
Loop the cable around a secure anchoring point such as a truss chord or fixed
structure so that it will catch the fixture if a rigging clamp fails. Take up
as much slack as possible in the safety cable (by looping it more than once
around the truss chord, for example).
See Figure 4. Open one of the retractable safety cable attachment eyelets
(arrowed) in the sides of the fixture and fasten the safety cable to it.
If there is any danger that the fixture may swing dangerously from the safety
cable if a primary attachment fails, open the second retractable safety cable
eyelet at the other end of the fixture and add a second safety cable as
described above, fastening it to this second eyelet.
Check that the fixture is now secured.
End-to-end alignment
The FR10 features alignment pins that let you line up fixtures perfectly end-
to-end to create an unbroken line of pixels. To use the alignment pins:
See Figure 5. The alignment pin release button is located on the base of the
fixture at the lefthand end when viewing the fixture from the control panel
side.
Slide the release button to the left to move the alignment pins out of the
fixture.
Engage the pins in the corresponding holes in the right-hand end of the next
fixture to line the two fixtures. The pins are for alignment purposes only, do
not apply a load to them.
Figure 5. Alignment pin release button
Standing an FR 10 Bar on a horizontal surface
To place an FR 10 Bar fixture standing horizontally on a stable horizontal surface:
Stand the fixture on its feet as shown in Figure 6. Make sure that it is safe and secure, and that it will not present a danger of tripping or falling.
If there is any danger of injury or damage if the fixture falls from the surface, secure it with a safety cable as described in `Securing the fixture with a safety cable’ on page 13.
Figure 6. FR 10 Bar placed on a horizontal surface
14
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
Installing on a rigging truss or similar structure
You can suspend an FR 10 Bar fixture from a rigging truss or pipe using the
brackets that are supplied with the fixture and rigging clamps that are
available from GLP as optional accessories.
If you are going to install the fixture hanging vertically downwards from a
horizontal rigging truss or pipe, you can fasten it to the truss using
G-clamps. If you are going to install the fixture in any other orientation or
if the rigging truss is not horizontal, you must use half-coupler clamps that
completely surround the truss chord or pipe. Rigging clamps must be approved
for the weight that they will support.
To install the FR 10 Bar on a rigging truss or pipe:
Check that the truss or pipe is secure and can safely hold ten times the
weight that it will support.
Using high-tensile steel screws or bolts and self-locking nuts, bolt at least
one rigging clamp to each of the two installation brackets that are supplied
with the fixture.
See Figure 7. Fasten the two brackets A supplied with the fixture to the
bottom of the base using four quarter-turn fasteners B per bracket. Turn each
fastener a full 90° to lock it.
Hold the fixture up to the truss and use the rigging clamps to fasten the
fixture securely onto the truss chord.
If there is any risk that the fixture will cause injury or damage if it falls,
secure it with a safety cable that is approved for the weight of the fixture,
rigging hardware, cables etc. as described in `Securing the fixture with a
safety cable’ on page 13.
B A
C
B
Figure 7. Brackets and rigging clamps
Impression FR10 Bar Quick Start and Safety Manual Rev. A
15
www.glp.de
6. AC mains power
Warning! Read Safety’ starting on page 4 for important safety information that you must understand before you install or operate the fixture. Check that all cables and connectors are suitable for the installation environment and application (see recommendations inAvoiding damage to the
fixture’ on page 9).
Use minimum 14 AWG or 1.5 mm2 power input and relay cables that are minimum 16
A-rated and temperature-rated to suit the application. In the USA and Canada
the cables must be UL-listed, type SJT or equivalent. In the EU the cables
must be type H05VV-F or equivalent.
Power cable
The FR 10 Bar is supplied with a power cord with a Neutrik powerCON TRUE1
connector for AC mains power input.
Connecting to power
The AC mains power supply must include a connection to ground / protective
earth. It must be protected against ground / earth leakage and overload. The
fixture’s internal auto-sensing power supply accepts AC power at 100-240 V,
50/60 Hz. Do not connect the fixture to power at any other voltage or to an
external dimmer.
The FR 10 Bar does not have a power ON/OFF switch. Power is applied to the
fixture as soon as the power cable becomes live.
The FR 10 Bar has a 3-conductor Neutrik powerCON TRUE1 Mains IN power input
socket that accepts AC power from a TRUE1 female cable connector. Although
TRUE1 connectors support hot-plugging, it is still good practice to shut down
power to power cables before connecting them to fixtures.
To connect the fixture to power:
If possible, shut down power to the power input cable.
Note the position of the keys and keyways on the TRUE1 power cable connector
and Mains IN socket and align them with each other carefully. Insert the cable
connector into the socket and twist clockwise to lock. Do not use force. If
the connector feels excessively stiff, remove it and check that it is lined up
correctly.
Before applying power to the power cable, check that nobody is looking
directly into the front of the fixture and check that there is no risk of
collision if the head tilts without warning.
To disconnect the fixture from power, pull the latch on the cable connector
outwards to release it, then twist the connector counterclockwise and pull to
remove it from the socket.
16
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
Installing power connectors
If you intend to draw power from convenience receptacles / consumer mains
power sockets, it is possible to install a suitable cord cap / power plug on
the supplied power cord / input cable. If you do this, check that the cord cap
/ plug is rated minimum 250 V, 16 A, that it has a connection to ground /
earth and that it has an integral cable grip. Follow the cord cap / plug
manufacturer’s assembly instructions.
If you need to install a Neutrik powerCON TRUE1 connector on a power cable,
follow the instructions given in the Support area of the Neutrik website at
www.neutrik.com.
Respect the color coding used in the supplied power cable and in your local
mains power wiring system. US and EU systems use the color coding shown below:
US system EU system
Live or L Black Brown
Neutral or N White Blue
Ground / Earth or Green
Yellow/green
Connecting multiple fixtures to power in a chain
You can connect fixtures to power in a daisy-chain to simplify your power
circuit layout.
Warning! Do not connect more than two (2) FR 10 Bar fixtures in total to power
in one chain at 100-120 V, 60 Hz. Do not connect more than four (4) FR 10 Bar
fixtures in total to power in one chain at 200-240 V, 50 Hz.
The power input cable supplied with the fixture is rated 16 A maximum. Add
together the maximum current draw ratings of all the devices that you intend
to connect to power in a daisy chain and do not create a chain with a total
maximum current draw of more than 16 A, or you will create a risk of fire and
electric shock.
To connect fixtures to power in a chain:
Obtain power relay cables that have male and female Neutrik powerCON TRUE1
connectors. Cables must be minimum 14 AWG or 1.5mm2, rated minimum 16 A and
suitable for the environment and application.
Connect the power input cable to the Mains IN socket of the first fixture.
If you are operating the FR10 Bar on 100-120 V, 60 Hz AC mains power, you can
connect maximum one FR10 Bar to the mains THRU socket (for a maximum of 2
fixtures total connected together in a chain) using a power relay cable. Do
not connect any devices to the Mains THRU socket of the second fixture.
If you are operating the FR10 Bar on 200-240 V, 50 Hz AC mains power, you can
connect maximum three FR10 Bars to the mains THRU socket (for a maximum of 4
fixtures total connected together in a chain) using power relay cables. Do not
connect any devices to the Mains THRU socket of the fourth fixture.
Impression FR10 Bar Quick Start and Safety Manual Rev. A
17
www.glp.de
7. Connecting to DMX data
Check that all cables and connectors are suitable for the installation
environment and application (see recommendations in `Avoiding damage to the
fixture’ on page 9).
The FR 10 Bar supports USITT DMX 512A, Art-Net and sACN DMX control data
signal protocols. It also supports RDM (Remote Device Management).
Two types of data connection are available:
· Two 5-pin XLR connectors for IN and THRU connections on a DMX data link
using standard DMX protocol. We recommend the use of digital 110 Ohm DMX cable
with original Neutrik 5-pin XLR HD connectors if connecting to the XLR
connectors.
· Two EtherCON sockets for IN and THRU connections on a DMX data link using
ArtNet or sACN protocol. You can use either socket for data IN or data THRU.
Use CAT6 or better Ethernet cables for the data link if connecting to the
Ethernet ports.
The EtherCON sockets use fail-safe technology that allows data through even if
the fixture is powered off.
If you would like advice with planning and installing a DMX link, your GLP
supplier will be happy to provide assistance.
18
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
8. Starting and stopping operation
Warning! Before you apply power to the fixture or operate it after a blackout,
make sure that nobody is looking directly into the front of the fixture and
that there is sufficient clearance for the head to tilt safely.
The FR 10 Bar’s TRUE1 mains power input connector supports hot-plugging, and
connecting and disconnecting a live power cable is an option, especially if
you need to shut down power urgently, but it is still good practice to shut
down power to the AC mains power circuit before connecting and disconnecting
power cables. To start operation, check that nobody is looking into the front
of the fixture and that there is no risk of collision of the head tilts
without warning, then apply power to the AC mains power circuit. To stop
operation, shut down power to the AC mains power circuit.
Transportation and storage
We strongly recommend that you transport the FR 10 Bar either in a flightcase
or in its original packaging to protect it from damage during transportation.
The product warranty does not cover damage caused by abnormal shocks during
transportation and handling. When the fixture is not installed, disconnect it
from power and store it in a dry location.
Impression FR10 Bar Quick Start and Safety Manual Rev. A
19
www.glp.de
9. Service
Warning! There are no user-serviceable parts inside the fixture. Any service
operation that requires removal of a cover must be performed by a professional
service technician with the tools, skills, and personal protective equipment
to maintain high-powered lighting equipment safely and efficiently.
Removing the front cover
The FR 10 Bar is supplied with a clear front cover installed. It is possible
to remove the front cover for cleaning or to replace it with one of the custom
front covers available from GLP.
To remove the front cover:
Place the fixture on a work surface with the head upright.
See Figure 8. Slide the two front cover quickrelease knobs (arrowed) down
towards the base.
Keeping the release knobs held down, slide the front cover out of the front of
the fixture.
When replacing the front cover or installing a diffuser, hold the release
knobs down and slide the front cover into the channels in the front of the
fixture. Release the knobs and check that the front cover is prevented from
sliding out of the channels.
Figure 8. Front cover quickrelease knobs
Cleaning
FR 10 Bar fixtures require occasional cleaning to prevent the buildup of dust,
dirt, and residue from atmospheric effects. Failure to keep the fixture clean
will significantly reduce light output and may cause heat buildup and damage
that is not covered by the product warranty. Regular cleaning will ensure
maximum performance and reliable operation.
The cleaning schedule depends on the operating environment. Check fixtures
regularly for signs of dirt buildup.
You can clean the fixture using a soft cloth slightly dampened with a
household or automotive glass cleaning product. Do not apply pressure to the
clear front or display on the back of the fixture, as you may scratch these
surfaces.
20
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
GLP Service and Support
Contact information for the nearest GLP Service and Support is available
online at www.glp.de/en/service, by email at info@glp.de, or by telephone at
the following numbers: · GLP Germany: +49 (7248) 927 19-55 · GLP N. America:
+1 818 767-8899 · GLP UK: +44 1392 690140 · GLP Asia: +852 (3151) 7730 · GLP
Nordic: +46 737 57 11 40
Impression FR10 Bar Quick Start and Safety Manual Rev. A
21
www.glp.de
10. Technical specifications
Optics
Total luminous output: 5860 lumens (wide), 4374 lumens (narrow) Light source:
10 x 60 W OSRAM Ostar RGBW LEDs Lifetime: 50 000 hrs. approx. to > 70%
luminous output Zoom ratio: 1:7 Minimum zoom angle: 3.7° half-peak (50%), 7°
field angle (10%), 8° cutoff angle (3%) Maximum zoom angle: 25° half-peak
(50%), 32° field angle (10%), 34° cutoff angle (3%) CRI: >80 CQS: >80 TLCI:
80 TM-30 Rf: 77 TM-30 Rg: 106 LED refresh rate: 2200 / 3000 / 4800 / 9600 Hz / 25k Hz
Effects
Color mixing: RGBW, 10 x pixels with grouped or independently variable control Zoom: 10 x pixels with grouped or independently variable full-range 1:10 zoom Virtual color wheel: 15 color presets, rotation, random color, rainbow colors Color temperature control: Variable 10 000 2500 K, fine-tuning via RGBW Dimmer: 0 100% continuous 16-bit electronic dimming, choice of two dimming curves Shutter: Regular and random strobe and pulse effects, instant open and blackout,
random pixel strobe 3-layer FX engine with light and zoom FX patterns Tilt: 200°, 16-bit control
Control and programming
Control systems: DMX, RDM via standard DMX link, Art-Net or sACN DMX control modes: 4 DMX channel footprint: 25, 51, 57 or 79 depending on mode Standalone operation: One captured scene Setting and addressing: Onboard control panel, backlit display with battery power,
DMX, RDM DMX compliance: USITT DMX512 RDM compliance: ANSI/ESTA E1.20
Installation
Options: Standing on horizontal surface, mounted on rigging truss or pipe at any angle Operating position: Any Minimum distance to combustible materials: 0.2 m (8 in.) Minimum distance to illuminated surfaces: 0.2 m (8 in.) Installation environment: Temporary or permanent indoor installation Secondary attachment: 2 x retractable safety cable attachment eyelets
22
impression FR10 Bar Quick Start and Safety Manual Rev. A
German Light Products®
Electrical
AC mains power: 100-240 V nominal, 50/60 Hz Power supply unit: Auto-ranging
electronic switch mode Maximum power consumption, all LEDs at 100% output: 800
W Idle power consumption, all LEDs at 0% output: 80 W Primary fuse: T 12 A,
250 V, 6×32 mm
Maximum permitted number of fixtures daisy-chained to power 2 x FR 10 Bar
total @ 100-120 V, 60 Hz 4 x FR 10 Bar total @ 200-240 V, 50 Hz
Connections
AC mains power IN and THRU: Neutrik powerCON TRUE1 Standard DMX data link IN
and THRU: 5-pin XLR Art-Net and sACN data link IN and THRU: Neutrik etherCON,
failsafe link integrity
Construction
Ingress protection rating: IP20 Fixture housing: High-impact flame-resistant
thermoplastic, aluminum alloy, steel Color: Black Interchangeable front screen
Integrated carrying handles Tilt lock Integrated multiple fixture alignment
system
Thermal
Cooling: Forced air, convection Minimum ambient temperature: 5° C (41° F)
Maximum ambient temperature: 45° C (113° F) Max. total heat dissipation: 2730
BTU/hr.
Included items
Power cable with Neutrik powerCON TRUE1 mains input connector 2 x brackets for
rigging clamps or surface mounting
Dimensions and weight
Height, head straight up: 339 mm / 13.3 in. Height, head horizontal: 254 mm /
10.0 in. Width across yoke: 1000 mm / 39.4 in. Depth, head straight up: 196 mm
/ 7.7 in. Min. center-to-center distance: 170mm / 6.7 in., 1000 mm / 39.4 in.
Weight: 24 kg (53 lbs.)
Impression FR10 Bar Quick Start and Safety Manual Rev. A
23
www.glp.de
11. Dimensions
FR 10 Bar
All dimensions are in millimeters
1000 209
339
189Folding brackets
69
130
970
138 60 138
370
130 196
24
impression FR10 Bar Quick Start and Safety Manual Rev. A
References
- LED Stage Lighting - Stage Lighting Products – GLP
- GLP German Light Products - Homepage
- Service - GLP.DE
- Homepage - Neutrik
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>