anslut 015743 Heater Fan Instruction Manual

: June 6, 2024
: anslut

Table of Contents

SAFETY INSTRUCTIONS
- SYMBOLS
TECHNICAL DATA
DESCRIPTION
USE
PROTECTIVE FEATURES
- Overheating protection
- Tip-over protection
MAINTENANCE
- STORAGE
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Item no. 015743
HEATER FAN

OPERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)
This product is only intended for well-insulated areas sporadic use.

Care for the environment!
Must not be discarded with household waste! This product contains electrical or electronic components that should be recycled. Leave the product for recycling at the designated station e.g. the local authority’s recycling station.
Jula reserves the right to make changes. In the event of problems, please contact our customer service.
www.jula.com

Manufacturer
Jula AB, Box 363, 532 24 SKARA

Distributor
Jula Poland Sp. z o.o., ul.
Malborska 49, 03-286 Warszawa, Polska
Jula Norge AS, Solheimsveien 30,
1473 LØRENSKOG

For the latest version of operating instructions, see www.jula.com
2021-05-06
© Jula AB

SAFETY INSTRUCTIONS

Keep children less than 3 years old under supervision when they are near the product. The product can be switched on/off by children from 3 to 8 years old only if it is mounted in the correct position to use, and if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Do not allow children from 3 to 8 years old to connect, use, clean or maintain the product.
This product can be used by children from 8 years and upwards and by persons with physical, sensorial, or mental disabilities, or persons who lack experience or knowledge if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Keep children under supervision to make sure they do not play with the product.
Do not allow children to clean or maintain the product without supervision. Keep children less than 3 years old under supervision when they are near the product.
The product is only intended for household use.
Pull out the plug if the product is not going to be used for some time.
Do not run the power cord in front of the product.
The product must only be connected to a correctly installed and earthed powerpoint. Check that the mains voltage corresponds to the rated voltage on the type plate.
Make sure to plug the plug firmly in the PowerPoint. Do not touch the power cord or the plug with wet hands.
Put the switch in the OFF position and pull out the plug when the product is not in use.
Do not route the power cord under carpets etc. Place the power cord so that there is no risk of treading on it, or tripping over it.
Do not expose children to the flow of air from the product for long periods.
Only use the product in a well-ventilated area. Do not place the product near walls or corners, where incoming or outgoing air can be blocked. Do not put the product near curtains, or other flammable materials – fire risk.
Do not expose the product to vibrations, knocks, or blows when in use.
Do not use the product in explosive environments, for example in the vicinity of flammable liquids, gas, or dust. Do not place the product near a naked flame or another source of heat.
Do not attempt to dismantle or repair the product. Repairs should be carried out by qualified personnel or an authorized service center.
A damaged cord or plug must be replaced by an authorized service center or qualified person to ensure safe use.
Do not use aerosol spray, e.g. insect spray or another flammable spray, near the product.
Switch off the product immediately and pull out the plug in the event of any abnormal noise, smell, smoke, or other sign of a problem.
Portable electric heating fans are intended for spot heating or as supplementary sources of heat. They are not intended to be used as the main heating system.

WARNING!

Some parts of the product get very hot – the risk of burn injuries. Keep the product under careful supervision when it is used by, or near children or persons with functional disorders.
Do not put any foreign objects on the product.
Never poke your fingers or any other objects into the inlet or outlet openings.
Do not use the product near a bath, shower, or swimming pool.
Do not cover the product, this can result in overheating.

SYMBOLS

| Read the instructions.
---|---
****| Safety class II.
| Do not cover.
| Approved in accordance with the relevant directives.
| Recycle discarded products in accordance with local regulations.

TECHNICAL DATA

Rated voltage	230 V — 50 Hz
Output	1200/2000 W
Safety class	II
Temperature interval	18 — 30°C
Size	19.6 x 45.2 x 19.6 cm

DESCRIPTION

Temperature control
Status light
Power switch
Protective grille
FIG. 1

USE

BEFORE USE

Unpack the fan heater and all the parts from the packaging and place them on a level surface as shown.
Check that the mains voltage corresponds to the rated voltage on the type plate.
Plugin the plug. The fan heater is now ready to use.

IMPORTANT:

Do not place the fan heater near walls or corners, where the incoming or outgoing flow of air can be blocked.
Do not place the fan heater directly below a PowerPoint.

STATUS LIGHT

The status light on the fan heater goes on when the plug is plugged into a live PowerPoint and the power switch is in the ON position. The status light stays on even when the set temperature is reached and the thermostat has switched off, to show that the fan heater is still working.

POWER SWITCH

The power switch (3) has 4 modes:
– off
– fan only
– LOW (1200 W)
– HIGH (2000 W).
Set the power switch to the required mode.

NOTE: Switch off the fan heater with the power switch (turn to 0/off mode) and pull out the plug when the fan heater is not in use.

SETTING THE TEMPERATURE

Turn the temperature dial (1) clockwise until it clicks – this shows that the thermostat has switched on. Continue turning the dial clockwise to set the required temperature.

NOTE: The first time the fan heater is used it may emit some fumes or smell. This is quite normal and is because the heating element has a protective coating from the manufacturing. The protective coating quickly vapourises and any fumes and smell go away.

SWITCHING OFF

Turn the power switch to the off position.
Turn the temperature dial anticlockwise all the way.
Pull out the plug and allow the fan heater to cool before putting it away.

PROTECTIVE FEATURES

Overheating protection

The overheating protection automatically switches off the fan heater if it overheats as a result of incorrect use or if used in very warm conditions. When the fan heater has cooled it can be used again. The fan heater also has a fuse plug that trips and disconnects the power in the event of severe overheating, short-circuiting, or other serious faults.

IMPORTANT: Take the fan heater to an authorized service center to be checked and repaired if problems with overheating persist.

Tip-over protection

The fan heater switches off automatically if it tips over or is turned upside down. When the fan heater has been stood upright it can be used again.

MAINTENANCE

NOTE: Switch off the fan heater, pull out the plug from the PowerPoint, and wait until it has completely cooled before cleaning and/or maintenance.

The most common reason for overheating is the accumulation of dust and other debris in the fan heater. Clean the ventilation openings and front grille with a vacuum cleaner at regular intervals.
Wipe dust off the fan heater with a soft cloth. Clean the fan heater when necessary with a cloth moistened with water and a mild detergent. Wipe dry with a soft, clean cloth.
The fan motor is permanently lubricated and does not need any further lubrication.
No further maintenance should be carried out by the user. Contact the retailer if additional maintenance or repairs are needed.

STORAGE

NOTE: Pull out the plug and allow the fan heater to cool before putting it away.

Pull out the plug and cover the fan heater to protect it from dust if it is not going to be used for some time.
Store the product in a cool, dry, and well-ventilated place.

TROUBLESHOOTING

Carry out the checks and measures in the table in the event of a malfunction. If normal functionality cannot be restored through the checks and measures in the table, or if the malfunction is not included in the table, contact the retailer.

Problem

| Possible cause|

Action