EDIFIER EDF160 Wireless Over-Ear Headphones User Manual

EDF160 Wireless Over-Ear Headphones
User Manual

Power ON/OFF

Power ON: Press and hold the MFB button for 3s when power OFF.
Power OFF: Press and hold the MFB button for 3s when power ON.

Pairing

1. Press and hold the MFB button for 3s when power off. Red and Blue LED will blink alternately and rapidly.
2. Select “EDIFIER STAX SPIRIT S3” in your device setting to connect. Blue LED will blink twice per 5s after connected.

Note:

1. For subsequent use, the headset will auto-connect to the device used last time.
2. Press and hold the MFB button for 5s when power off to skip the latest connected device and pair the new Bluetooth device.

Reset

1. Power on and disconnected to any Bluetooth devices.
2. Simultaneously press and hold the “+” “-” buttons for 5s to reset and start Bluetooth pairing.
3. Blue LED will blink 6 times rapidly when successful.

Dual Connectivity

1. Pair devise A with the headphone. Upon success, press and hold the MFB button for 5s again.
2. Select “EDIFIER STAX SPIRIT S3” in device B to connect succesfully.
3. Select “EDIFIER STAX SPIRIT S3” in device A to connect manually. Blue LED will blink twice per 5s when successful.

Charge

1. Please connect the product to a power source with the included Type-C charging cable for charging.
2. Red LED is steady lit when charging and off when fully charged.

Input: 5V 1.5A

AUX Cable

1. Connect the AUX cable to the headphone when power on, and the headphone will switch to the AUX-in sound source state; connect the AUX cable to the headphone when power off, the headphone will not power on automatically, need to press and hold the MFB button for 3s to turn on.
2. Unplug the AUX cable from the headphone and the headphone will power off automatically.
3. Green LED is steady lit when in the AUX-in sound source state.

Controls

Note:

1. ___: Press and hold.
2. Please do not charge the headset when there is sweat or other liquids inside the charging port, which may damage the headset.
3. Images are for illustrative purposes only and may differ from the actual product.
4. Download Edifier Connect App for more customizable control settings.

Ear cushion replacement method

Snapdragon Sound is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Snapdragon and Snapdragon Sound are trademarks or registered trademarks of Qualcomm Incorporated.

FCC statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC statement:CAN ICES-3(B)/NMB-3(B).
FCC ID: Z9G-EDF160
IC: 10004A-EDF160
Declaration for EU
Frequency Band: 2400Mhz – 2483.5Mhz
RF Power Output: ≤15 dBm (EIRP)
There is no restriction of use.
210-170531
Input: 5V 1.5A
Hereby, Edifier International Limited declares that the radio equipment type EDF200071 is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address: https://www.edifier.com/int/eu-doc.html

FCC Regulatory Compliance

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
ISED Regulatory compliance
This device contains license-exempt transmitters that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

For more information, please visit our website:

www.edifier.com

Model: EDF200071
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong
www.edifier.com
2022 Edifier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade, information contained herein may be subject to change from time to time without prior notice.
Products of EDIFIER will be customized for different applications.
Pictures and illustrations shown in this manual may be slightly different from the actual product.
If any difference is found, the actual product prevails.
V1.0

References

• Headphones, Speakers | A Passion for Sound -【Edifier】

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>