globe 50466 Smart Recessed Lighting Kit Installation Guide
- June 6, 2024
- globe
Table of Contents
globe 50466 Smart Recessed Lighting Kit
Thank you for selecting Globe as your smart home solution. With proper care, this product will provide years of pleasure and enjoyment.
Check out the installation video on our website: globe- electric.com/smart
SAVE THESE INSTRUCTIONS
Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for working with electricity.
- Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work.
- Before touching any wire, use a voltage tester to make sure it’s not live. Whenever you check for voltage in a receptacle, check both outlets—€ach may be controlled by a separate wiring circuit.
- To protect children, place safety covers over any unused outlets.
- Always work with enough light to see what you are doing; it’s easy to make mistakes when you’re working in dim light.
Before assembling your lighting fixture, TURN OFF THE POWER and consult a qualified licensed electrician.
- IC-rated for direct contact with insulation
- Energy Star
- Wet-rated
- Airtight per ASTM-E283-04
- CAN ICES-005 (B)
LIMITED WARRANTY
This smart recessed light is warranted to last 3 years from the date of purchase based on use of3 hours per day. If it fails before that time, we will replace it. Send the recessed light, proof of purchase and register receipt along with your complete name and address to Globe Electric. See caution text for proper use. This warranty is void if this product is misused in any way. This replacement is the sole remedy available and liability for incidental or consequential damage is expressly excluded. This device is not intended for use with emergency exit fixtures or emergency exit lights, photocells and electronic timers.
This device complies with Part lS of the FCC rules. Operation is subject to
the following two conditions: n) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications made to this product are not expressly approved by
the party responsible and could void the user’s warranty of the equipment.
FCC Statment
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
fol lowing measures: Reorient or relocate the receiving antenna. Increase the
distance between the equipment and receiver. Connect the equipment to an
outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and operated with
minimum distance 20cm between the radiator & your body.
USER MANUAL NOTICE FOR LICENSE-EXEMPT RADIO APPARATUS
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. CAN
ICES-005 (B).
RADIATION EXPOSURE STATEMENT:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
WARNINO:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
FCC RESPONSIBLE PARTY
Globe Electric 15301 Shoemaker Ave, Norwalk, CA 9065 0 www.globe-
electric.com
FEATURES
- LED integrated • dimmable through the app
- RGB: Choose from a full spectrum of colors
- Tunable white (2000 K • 5000 K): Choose from a focused bright white to a relaxed sunset glow
- Set schedules and control your light from anywhere
SPECIFICATIONS
-
390 lumens (at 5000 K)
7watt -
Lasts 50,000 hours
CRl90 -
120V•60Hz
IC-rated -
Indoor/outdoor use
Minimum starting temperature: -18 • C (0 • F)
Since 1932, Globe has taken pride in offering products of the highest quality,
and a level of service unparalleled in the industry. Should you encounter any
difficulties, have any questions or simply wish to offer us your valuable
feedback, you may contact us in the following ways:
Toll Free Telephone: 1-888-543-1388
(North America Only) /Toll Free Fax:
1-800-668-4562
(North America Only)
E-Mail: info@lglobe-electric.com
Mail: Globe Electric Customer Service Department
150 Oneida, Montreal, Quebec, Canada H9R 1A8
Please visit our website to discover other quality Globe products: http://www
.globe-electric.com
PRE-INSTALLATION
Planning Installation
Compare all parts with the “Hardware Included” section. If any part appears
missing or damaged, do not install this product and contact the Customer
Service team at 1-888-543-1388 or
e-mail to info@globe-electric.com.
Tools Required
Hardware Included
NOTE: Hardware is not shown to actual size.
| Item | Quantity |
|---|---|
| light panel + receiver+ cable | 1 |
| junction box+ cable | 1 |
| foam gasket | 1 |
INSTALLATION
Improper wiring of any electrical device can cause fire, serious injury or death. Always consult a qualified licensed electrician who will ensure the switch is installed in accordance with local electrical codes and regulations. Before starting the installation, ensure the power is disconnected at the circuit breaker and test the existing switch with a voltage tester.
caution
- Make sure that the power at the circuit breaker is off before wiring.
- Neutral wire is required. Confirm the wall box contains a neutral wire (typically white).
- The wire colours indicated in this manual are common colors and may differ in some homes. Please contact an electrician if you have different wire colours.
- Ensure the wire conductors are securely fastened to each wire.
- DO NOT USE WITH STANDARD DIMMER.
|
Step l
Turn power OFF from the electrical panel prior to installation.
Step2
Determine the location for installation and cut a hole of the appropriate size
in the ceiling. Refer to the hole diameter table for appropriate sizes or use
the supplied template on the “Hole Size” page.
cutting hole diameter
3,25 inch slim| 31/4″ ± 1/8″ (76 ± 3mm)
Step3
- Open the junction box cover and remove the appropriate knockout(s) on the side panel.
- Insert the electrical supply cable through the knockout. If you do not have electrical wiring experience, Globe recommends consulting a qualified licensed electrician who will ensure the fixture is installed in accordance with local installation codes.
- Using quick-connect push-in terminals, connect the green ground wire to the green wire terminal; the black wire to the black wire terminal; the white wire to the white wire terminal.Use the cable clamp to secure wire in knockout hole.
Step4
Place all wiring and connections back into the box and close the cover. Plug
the connector cable from the junction box into the light panel, secure with
screw cover.
Steps 5
Insert the junction box through the mounting hole.
Step6
Push spring-loaded clips on the fixture upwards and insert the fixture base
into the mounting hole. Release the clips and the fixture will be pulled flush
with the ceiling.
NOTE: For airtight requirements, ensure the foam gasket remains between
fixture and ceiling.
Once the fixture has been installed, you’re now ready to pair it with the Amazon Alexa app (see connecting instructions).
HOLE SIZE
Make sure your mobile device is running iOS 9.0/watchOS 2.0/Android 4.4 or higher.
Let’s get started!
-
Download the Globe Suite™ app from the App Store or Google Play to your mobile device.
-
Launch the Globe Suite™ app.
-
To register, enter your email address. Create a password, then login to the app.
OR -
Login if you already have an account.
Verify your network
- Verify your network and ensure your mobile device is connected to a 2.4 GHz Wi-Fi channel.
- Consult your router documentation for detailed instructions on how to change wireless settings.
Scan mode
- Power on your device.
- Select the “+” symbol on the top right hand corner.
- Follow instructions within the app.
- If your device is flashing rapidly and fails, try using EZ Mode.
EZ mode
- Select the “+” symbol on the top right hand corner.
- Select “Manual”.
- Select your product type and follow the instructions within the app.
- If the connection fails, try using AP mode.
AP mode
- Select the “+” symbol on the top right hand corner.
- Select “Manual”.
- Select your product type.
- Open the menu on the top right hand corner and select “AP mode”.
- Follow the instructions within the app.
- You’re good to go!
Did you know?
Most modern routers are dual band meaning they support both 2.4 GHz and 5 GHz
channels. The most common wireless options are:
-
Mixed:
The router will broadcast both 2.4 GHz and S GHz simultaneously under the same 551D. The device will choose which to connect to based on multiple variables (congestion, distance to router etc.). -
2.4 OHz: Broadcast only on this channel.
-
5 OHz: Broadcast only on this channel.
-
Dual 2.4 and 5 OHz using Separate SSIDS: Router will broadcast both channels and user manually decides which to connect to.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>