eta LATTEO Milk Frother and Milk Heater User Manual

Milk frother and milk heater
• USER MANUAL

Milk frother and milk heater eta 6189
INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Keep these instructions including the warranty, the receipt, and, if possible, the box with the internal packing.

SAFETY WARNING

GENERAL PROVISIONS:
– Before the first use, read the instructions for use carefully, look at the picture and store the instructions for use for the future. Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
– Check whether the data on the type label corresponds with the voltage in your socket. The power cord plug has to be connected to the properly connected and grounded socket according to the national standard.
– This product can be used by children at the age of 8 years and older if they are supervised or if they were instructed regarding the use of the appliance in a safe way and if they understand possible risks. User cleaning and maintenance must not be performed by children if they are younger than 8 years and unsupervised. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
– The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers.
– Children must not play with the appliance.
– The appliance is intended for heating a maximum of 0,3 l of milk. If the milk level exceeds the maximum recommended amount, hot milk maybe splashes out.
– WARNING: Do not open the lid if the milk is hot.
– CAUTION – Do not use the appliance with a program, time switch, or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
– When the appliance is in operation, prevent pets, plants, or insects to get in contact with it.
– Do not plug the fork of the supply cord into the power outlet and do not unplug the cord with wet hands or by pulling by the supply cord!
– Use the appliance with the stand designed for this type only and only for its intended purpose.
– Prevent injuries when handling (e.g. by hot milk, steam).
– The appliance (heating element) is equipped with heat protection against overheating. If it happens, unplug the appliance from the power supply and let it cool down.
– Use this appliance only for the purpose for which it was designed as specified in this user‘s manual. Never use the appliance for any other purpose.
– The producer is not responsible for damage caused by improper use of the appliance (e.g. burning, scalding, fire), and its guarantee for the appliance does not apply to situations when the safety warnings above are not complied with. USE OF THE APPLIANCE:
– Use the appliance with the stand designed for this type only.
– Never immerse the appliance and the stand-in water and other liquids (even partially)!
– Never leave the appliance unsupervised and check it during the whole time of milk heating!
– This appliance is not intended for outdoor use.
– Never touch rotating parts. Risk of injury!
– The appliance is intended for home use and similar (in shops, offices, and similar workplaces, in hotels, motels, and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
– Use the appliance in the working position only at places with no risk of turning over and insufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable objects (e.g. curtains, drapes, etc.), and wet surfaces (e.g. sinks, washbasins, etc.).
– Do not place the appliance near objects or under objects which could get damaged by steam, e.g. walls, kitchen cupboards, sideboards, paintings, or curtains. Leaking steam could damage them. – Do not use the appliance in an environment saturated with explosive or flammable steams.
– There must be milk in the appliance before putting it into operation. Do not fill the appliance with milk if it is on the stand.
– Do not touch outer surfaces during the operation of the appliance, they are hot and there is a risk of getting burned. Do not touch the lid during and after cooking!
– Before switching on the appliance ensure that the milk level is between MIN and MAX marks.
– If you are not going to use the appliance for a longer time, we recommend unplugging the stand from the power supply by taking the fork of the power cord out of the socket.
POWER CORD:
– If the power cord of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
– Never use the appliance if its power cord or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to the water. In this case, take the appliance to a special service to check its safety and proper function.
– Never put the power cord on hot surfaces or do not let it hang over the edge of a table or a worktop. Plugging or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!
– The power cord must not be damaged by sharp or hot objects, open fire, it must not be sunk into water or bent over sharp edges.

DESCRIPTION OF THE APPLIANCE (Fig. 1)

A – milk frother
A1 – button – switching the appliance on/off and selecting the function *
A2 – shaft
A3 – handle
A4 – lid
B – removable stand
B1 – central connector
B2 – power cord
C – mixing adapter (intended for heating of milk)
D – foaming adapter (intended for making a big amount of milk foam)

• The length of the program depends on the selected function as well as the amount of used milk. If the button is not pressed during approx. three seconds, the blinking LED will go to continuous lighting mode and the selected function will start.

INSTRUCTIONS FOR USE

The device is intended for foaming/heating of coffee milk. It can be used for making Latte, Cappuccino, Frappe, and other drinks with milk foam/hot milk. First, remove all packaging materials, take out the milk frother all accessories. Then remove all adhesive foils, stickers, and paper from the milk frother and accessories. Before the first use, wash all parts, which will be in contact with food, in warm water with a mild detergent, thoroughly rinse in clear water and wipe dry or let dry.

Warm milk, for mixing and heating milk
Warm and creamy foam, for warm creamy and fine-pored milk foam
Heating milk with a small amount of foam, for warm, creamy, and fine-pored milk foam with a bigger amount of liquid milk
Cold foam, for cold, creamy milk foam

APPLICATIONS Unwind the necessary length of the power cord B2 from the storage space of stand B. Place the stand on a suitable surface, at a height of about 85 cm, out of reach of children and incapacitated persons, and plug the fork of the power cord into the electric socket. Hold the milk frother A on the handle A3 and shift lid A4 to remove it. Take adequate adapter C/D (see the function in the table above) and press it onto shaft A2, up to the stop. Pour milk into the vessel below the mark (observe maximum amounts in the table above). The minimum and maximum amounts of milk are indicated on the inner wall of the vessel. Place lid A4 back onto the vessel and put the vessel onto removable base plate B. Set the required function ( ) by repeated pressing button A1. The selected function will be highlighted by the relevant LED. The device starts whipping or, as the case may be, heating the milk. As soon as the process is completed, the device will switch off automatically. The process can be stopped by short pressing button A1 at any time.

Notice
– Lifting the container off the stand cancels all the set functions.
– Wait 2 – 3 minutes before the next use of the device.
– The adapter on the bottom of the vessel must be immersed in milk (min. 50 ml.).
– Overheating of the device can occur in case of an insufficient amount of milk. Overflowing can occur in case of an excessive amount of milk.

Note
– The amount and quality of the foam can strongly differ, depending on many factors, such as the use of fresh or treated milk, the content of milk fat, milk temperature, and more.
– Do not use the milk that has been stored in a vessel for a long time. Always use fresh milk.
– We recommend using whole cow milk, fat content > 3.0%. Other kinds of milk (e.g. low-fat or skimmed milk) will have a different behavior during foaming.
– The milk should be cold.
– The volume of milk will increase by foaming.
– If the milk foam seems to be very thin, wait for approximately 30 seconds. During this period of time, liquid milk can drop and the foam will have a better consistency.
– Do not try to foam the milk again, if you don´t like its taste.
– If the milk starts overflowing, switch off the device immediately, allow it to cool, and then clean it (see V. Maintenance).

TROUBLESHOOTING

cord, plug and el. socket
Overheating protection prevents switching on the device (All LEDs are on)| Disconnect the device from the socket and allow it to cool
The heating and foaming process will be stopped earlier| If your start the next foaming and/or heating process after the preceding one, it will take less time| Wait 2 — 3 minutes before the next use of the device
The milk
becomes warm, however, it
does not make adequate foam| Have you used a suitable adapter?| Use the right adapter
Are the adapter/the bottom of the vessel clean?| Remove the did and
PROBLEM| CAUSE| SOLUTION
---|---|---
Excessive noise| Has enough milk been added
into the vessel?| Check these conditions
Has the coil been correctly
installed on the adapter?| Check these conditions
Has the lid been correctly
installed on the container?| Check these conditions
The shaft does
not rotate| The shaft has been blocked by
solid dirt| Remove the dirt from the vessel and
loosen the shaft manually

MAINTENANCE

Unplug the appliance from the power supply by taking the fork of the power cord out of the socket! Clean the kettle only when it is cooled down! Do not use rough and aggressive detergents (e.g. sharp objects, scrapers, diluting agents, or other solvents)! Also do not use any pressure cleaning equipment (e.g. dishwasher). Clean the vessel and the adapter immediately after each use, thus avoiding the rest of the milk from becoming dry. Remove the sealing ring on the lid and the adapter on the bottom of the vessel. If the accessories are not easy to remove from the shaft, fill the container with warm water and leave them to soak (for about 10 min.). Remove the accessorize. Let all the parts dry properly after maintenance. The surface color will change over time which is normal. This change does not affect the surface properties. It is not a material defect of the container and the appliance is not subject to a complaint about this reason.

Storage
If not used, the adapter should be stored in the holder on the lid. Make sure that the appliance is cold and dry before storage. Store the appliance in a safe and dry place, out of
the reach of children and incapacitated persons.
Expert service must do the large maintenance or intervene into inside parts of the appliance! Non-observance of the instructions of the manufacturer cancels the right to guarantee repair!
If you are unable to fix the problem, or if you need any further information about the appliance or service centers, please contact your distributor.

ENVIRONMENT

Printed signs of materials used for manufacture, packing, components, and accessories, as well as their recycling, are on all the pieces if their dimensions enable it. The symbols on the product or in the accompanying documentation mean that the used electric or electronic products must not be disposed of together with municipal wastes. Please, hand them over to the collection points designed for their correct disposal, where they will be accepted free of charge. By correct disposal of this product, you can help to preserve valuable natural resources and help to prevent possible negative impacts to the environment and to human health, which could be the results of incorrect waste disposal. For further details ask the municipal authorities or the nearest collecting point. Penalties can be charged for incorrect disposal of such wastes, according to national regulations. If the appliance is to be put out of operation definitely, we recommend cutting off the feeder cable, to disable its use.

TECHNICAL DATA

Voltage (V)
Absorbed power (W)
Max. volume (l)
Weight (kg) approximately
Protection class of the appliance
Input in off mode is| shown on the type label of the appliance
shown on the type label of the appliance
0.3
1
I.
< 0.50 W
---|---

The manufacturer reserves the right to change the technical specifications and accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING, OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY; DO NOT IMMERSE IN WATER OR OTHER LIQUIDS; TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.
The symbol indicates a WARNING.
The symbol indicates do not use the dishwasher.

© DATE 18/1/2021
e.č. 03/2021

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>