SENA A20 Parani Bluetooth Intercom Headset User Manual

A20 Manual

Charging

Power On/Off

(+) Button + (-) Button for 2 sec

Volume Adjustment

(+) Button – Increase the volume
(-) Button – Decrease the volume

Phone, Music Pairing

Initially Pairing the A20 The Bluetooth system will automatically enter the phone pairing mode when you initially turn on the Bluetooth system or in the following situation:
• Rebooting after executing Factory Reset

1.  Press and hold the Multi-function button and (+) Button for 1 second.
2. Search for Bluetooth devices on your mobile phone. Select the Paranal A20 in the list of the devices detected on the mobile phone.
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.

Music Operation

Play or pause music: Press the Multi-function Button for 1 second.
Trackback: Press the (-) Button for 1 second.
Track forward: Press the (+) Button for 1 second.

Mobile Phone Call Making and Answering

Answering a call: Tap the Multi-function Button
Ending a call’ Press the Multi-function button for 2 seconds.
Voice dial: Press the Multi-function button for 3 seconds.
Speed dial: Press the (+) Button for 3 seconds.
Rejecting a call: Press the Multifunction Button for 2 seconds.

Intercom Pairing

1. Press and hold the Multi-function Button of two Bluetooth systems for 5 seconds until the red LEDs of both units start to flash rapidly.
2. Simply tap the Multi-function Button of any one of the two Bluetooth systems.

Intercom Start/End

1st Friend: Tap the Multi-function Button once.
2nd Friend: Tap the Multi-function Button twice.
3rd Friend: Tap the Multi-function Button triple times

Radio On Off

Turn on the FM radio: Press the (-) Button for 1 second.
Turn off the FM radio: Press the (-) Button for 1 second.

Radio Seek Stations

Seek up stations: Double-tap the (+) Button.
Seek down stations: Double-tap the (-) Button.

Setting

Configuration Menu: Press the Multi-function button for 15 seconds.

Troubleshooting

Factory Reset
If you want to restore the Bluetooth system to factory default settings, use the Factory Reset in the configuration menu. The Bluetooth system automatically restores the default settings and turns them off.

Certification and Safety Approvals FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antennae -Increase the separation between the equipment and the receiver -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. When equipped, the distance between the antenna and one’s head surface is 38mm.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada(IC) Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>