SENA SP92 PI Bluetooth Communication Headset User Manual

SENA SP92 PI Bluetooth Communication Headset

PI MANUAL

Charging

• Red LED: Charging
• Blue LED: Fully charged

Power On/Off

• Power On : Press and hold the (+) Button and (-) Button for 1 second
• Power Off : Tap the (+) Button and (-) Button.

Volume Adjustment

• (+) Button – Increase the volume
• (-) Button – Decrease the volume

Battery Check

Phone, Music Pairing

Initially Pairing the pi
The headset will automatically enter the phone pairing mode when you initially turn on the Bluetooth system or in the following situation:

• Rebooting after executing Factory Reset
  1. Press and hold the (+) Button and (-) Button for 1 second.
  2. Search for Bluetooth devices on your mobile phone. Select the pi in the list of the devices detected on the mobile phone.
  3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.

Music Operation

Play or pause music: Press the (+) Button for 1 second.
Track back: Press the (-) Button for 2 seconds.
Track forward: Press the (+) Button for 2 seconds.

Mobile Phone Call Making and Answering

• Answering a call: Tap the (+) Button
• Ending a call: Press the (+) Button for 2 seconds.
• Rejecting a call: Press the (+) Button for 2 seconds.
• Voice dial: Press the (+) Button for 3 seconds.

Intercom

Intercom Pairing
1. Press and hold the (-) Button for 1 second of two headsets to enter the Intercom Menu.
2. Tap the (+) Button of two headsets until red LEDs of both units start to flash rapidly.
3. The two headsets(A and B) will automatically paired.

Intercom Start/End :
1. Press and hold the (-) Button for 1 second to enter the Intercom Menu
2. Tap the (-) Button

Setting

Configuration Menu: Press the (-) Button for 5 seconds.

Using the Sena Device Manager
Connect the headset to your computer via a USB cable. Launch the Sena Device Manager and click DEVICE SETTING to configure the headset settings.

Installing the Headset on your Helmet

1. Secure the headset to the chinstrap using the strap hooks on both sides.
2. Slide the headset as close to the helmet as possible

Note :
The [R] and [L] makings are located on the back of the headset. Make sure that the cable is facing toward the helmet.

3. Hide the cable under the inner pad in the front of the helmet.
4. Adjust the headset upward or downward so that the speakers are facing your ears.

Troubleshooting

Factory Reset
If you want to restore the headset to factory default settings, use the Factory Reset in the configuration menu. The headset automatically restores the default settings and turns off.

Certification and Safety Approvals FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antennae
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Statement

The highest SAR value reported under this standard during product certification for use next to the head with the minimum separation distance of 0mm is 0.967W/Kg. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. This product is compliance to FCC RF Exposure requirements and refers to FCC website
https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: S7A-SP92, IC:8154ASP92.

FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

Industry Canada(IC) Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>